• Fire Science and Engineering
• /
• v.33 no.1
• /
• pp.50-59
• /
• 2019

Experimental and numerical studies on the fire characteristics according to the distance between the fire source and sidewall under the over-ventilated fire conditions. A 1/3 reduced ISO 9705 room was constructed and spruce wood cribs were used as fuel. Fire Dynamics Simulator (FDS) was used for fire simulations to understand the phenomenon inside the compartment. As a result, the mass loss rate and heat release rate were increased due to the thermal feedback effect of the wall in the compartment fire compared to the open fire. As the distance between the fire source and sidewall was reduced, the major fire characteristics, such as maximum mass loss rate, heat release rate, fire growth rate, temperature, and heat flux, were increased despite the limitations of air entrainment into the flame. In particular, a significant change in these physical quantities was observed for the case of a fire source against the sidewall. In addition, the vertical distribution of temperature was changed considerably due to a change in the flow structure inside the compartment according to the distance between the fire source and sidewall.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.4
• /
• pp.46-51
• /
• 2004

The objective of this study was to evaluate the applicability of high temperature drying to pitch pine (Pinus rigida) lumber, especially intended for use as lamina of structural glued laminated timber (glulam), to enhance the efficient utilization and provide added-value to that species. The high temperature schedule and drying procedures utilized were shown to be reasonable for drying glulam lamina due to the occurrence of small moisture gradients, minimal residual drying stress, and low warpage. Through preliminary tests, it was confirmed that residual resin at lamina surfaces did not adversely affect the gluing process. However, quantitative analysis of resin is required for developing a method to constrain the occurrence of pitch trouble with respect to decreasing long-term adhesive and finish durability of glulam in use after manufacturing. The final moisture content of high temperature dried lamina was much lower than target moisture content and discoloration was more severe than anticipated. In a further study, it will be necessary to determine the optimal drying conditions, such as temperature, humidity, drying time, and top load restraint level, which could best control discoloration, warpage, and moisture content of the lamina, while minimizing fuel expense.

• New & Renewable Energy
• /
• v.18 no.3
• /
• pp.10-22
• /
• 2022

Forest biomass energy is based on scientific evidence in response to carbon neutrality and the climate crisis, international consensus, and environmental-geographic characteristics of each nation. In this study, the authors aimed to analyze macroscopic forest biomass energy policies for ten major countries. They categorized them into six detailed categories (Sustainable utilization, Cascading Uutilization, Replacement of fossil fuel/Carbon intensive products, Utilization of forest by-products/residues as the source of energy, Contribution to carbon-neutral/climate change, and Biomass combined with CCS/CCUS ). In addition, the surveyed nations have developed a policy consensus on the active use of forest biomass with sustainable forest management except for the cascading utilization category. Furthermore, the authors evaluated the mid to long-term plans of the Korean government for improvements in the policy and legal aspects. As a result, the authors derived four major directions that South Korea should approach strategically in the future (1) secure financial resources for sustainable forest management and stimulating investment in the timber industry, (2) promote unified policies to establish a bio-economy, (3) enhancement of the forest biomass energy system, and (4) reorganization and promotion of strategy centered on the opinions of field experts in internal and external instability.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.739-744
• /
• 2013

In this study, torrefaction was performed to improve fuel properties of Larch. The optimal condition for torrefaction was investigated by response surface methodology. The torrefaction temperature and time ranged $220{\sim}280^{\circ}C$ and 20~80 min, respectively. As the torrefaction temperature and time increased, the carbon content of torrefied biomass increased from 49.36 to 56.65%, while its hydrogen and oxygen contents decreased from 5.56 to 5.48% and from 37.62 to 31.67%, respectively. The weight loss and calorific value increased with SF, while energy yield decreased. At the severe torrefaction condition (SF 7), the weight loss and calorific value were 26.58% and 22.30 MJ/kg, respectively. The energy contained in torrefied biomass increased to 20.41%, when compared with the untreated biomass. As the torrefaction severity increased, the energy yield decreased due to the relatively high weight loss of biomass. Therefore, the highest energy yield was obtained at high calorific value and low weight loss of biomass (SF 5.72).

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.89-95
• /
• 2009

The current enforce decree of "The Act on the Promotion of Construction Waste Recycling" divides seventeen kinds of construction wastes by property and configuration. Mixed construction waste, one of them classified by the enforce decree, is composed two more than justified construction wastes except refuse soil and rock. In construction wastes justified by enforce decree of this law, most refuse concrete and asphalt concrete of construction wastes are recycled. As well as refuse metal is separated, sorted from bulk them, and merchandised for value. Finally this is used the secondary manufactured products. Even though combustible construction wastes like refuse wood, plastics, fiber can be recycled RDF(Refuse derived fuel) or RPF(Refuse plastic fuel) because of high caloric value and low heavy metal but most of them are discharged as mixed construction waste and then treated by treated by incineration and landfill. Therefore, to control construction waste flow efficiently, construction wastes are classifies first combustible, incombustible, mixed combustible, incombustible and etc. in this study. The combustible waste is consisted refuse wood, plastics, fiber and etc. and incombustible waste contains refuse concrete, asphalt, and etc. Mixed construction is construction waste that can not separate from mixed waste bulk with different kinds.

• Journal of Environmental Science International
• /
• v.27 no.2
• /
• pp.91-97
• /
• 2018

This study carried out first a component survey on the domestic waste shipped into a waste disposal facility in B city, and then heavy metal analysis of each component according to the SRF standards. Based on this, this study explored the problems with domestic waste and measures to improve them. The results are as follows. The result of the survey of physical components show that paper accounted for the largest proportion with 20.5 %~59.9 %, metals (including batteries) among incombustibles accounted for 0.0~8.3 %, other inorganic substances, glass and ceramics accounted for 0.0~43.7 % and 0.0 %~19.6 % respectively. However, the proportion of coated viny and plastics, which have high lead and cadmium content, was rather high with 2.9 %~30.9 %. This suggests the possibility that actual concentration of lead and cadmium within SRF is likely to be higher. Among the 15 components contained in the waste brought into the waste disposal facility, 10 components (food waste, textiles, vinyl, plastics, wood, rubber and leather, paper, metals, electronic substrates, and nail polish) were analyzed according to assay samples (approximately 0.1 g and 0.3 g). The result of analysis shows that the amount of Cd and Pb detected in coated vinyl for 0.109 g of assay sample was 98.6 mg/kg and 20.6 mg/kg respectively; 117.0 mg/kg and 29.0 mg/kg respectively for 0.313 g of assay sample. This is high contents exceeding the Cd standard. As for wooden component, the amount of Pb was 480.0 mg/kg for 0.3 g of assay sample. This suggests that there always exists the possibility of exceeding the exposure level of heavy metals (Cd and Pb) in SRF as long as coated wood and vinyl plastics with high contents of Pb and Cd are shipped into the waste disposal facility; and the local government and the residents need to work hard to improve the situation including development of the machine to sort electronic substrates and batteries for separate collection of the waste of coated vinyl and plastics within domestic waste.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.3
• /
• pp.271-282
• /
• 2020

Sewage treatment plants are social infrastructure of cities. The sewage distribution rate in Korea is reaching 94% based on the sewage statistics based in the year of 2017. In Korean sewage treatment plants, use of PAC (Poly Aluminum Chloride) accounts for 58%. It contains a large amount of impurities (heavy metal) according to the quality standards, however, there have been insufficient efforts to reinforce the standards or technically improve the quality, which resulted in secondary pollution problems from injecting excessive coagulant. Also, the increase in the use of chemicals is leading to the increases in the annual amount of sewage sludge generated in 2017 and the need to reuse sludge. As such, this study aims to verify the possibility of reusing sludge by evaluating the stability of heavy metals based on the injection of coagulant mixture during water treatment which uses the torrefield wood powder and natural materials, and evaluating the sedimentation and heating value of sewage sludge. As a result of analyzing heavy metals (Cr, Fe, Zn, Cu, Cd, As, Pb, and Ni) from the coagulant mixture and PAC (10%), Cr, Cd, Pb, Ni, and Hg were not detected. As for Zn, while its concentration notified in the quality standards for drinking water is 3 mg/L, only a small amount of 0.007 mg/L was detected in the coagulant mixture. Maximum amounts of over double amounts of Fe, Cu, and As were found with PAC (10%) compared to the coagulant mixture. Also, an analysis of sludge sedimentation found that the coagulant mixture showed a better performance of up to double the speed of the conventional coagulant, PAC (10%). The dry-basis lower heating value of sewage sludge produced by injecting the coagulant mixture was 3,378 kcal/kg, while that of sewage sludge generated due to PAC (10%) was 3,171 kcal/kg; although both coagulants met the requirements to be used as auxiliary fuel at thermal power plants, the coagulant mixture developed in this study could secure heating values 200 kal/kg higher than the counterpart. Therefore, utilization of the coagulant mixture for water treatment rather than PAC (10%) is expected to be more environmentally stable and effective, as it helps generating sludge with better stability against heavy metals, having a faster sludge sedimentation, and higher heating value.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.975-984
• /
• 2018

Fast pyrolysis bio-oil has unfavorable properties that restrict its use in many applications. Among the main issues are high acidity, instability, and water and oxygen content, which give rise to corrosiveness, polymerization during storage, and a low heating value. Esterification and azeotropic water removal can improve all of these properties. A 500 g of Quercus mongollica which grounded 0.8~1.4 mm was processed into bio-oil via fast pyrolysis for 2 seconds at $550^{\circ}C$. The esterification consists of treating pyrolysis oil with a high boiling alcohol like n-butanol at $70^{\circ}C$ under reduced pressure (100 hPa). All products are analyzed for water mass fraction, viscosity, higher heating value, pH, FT-IR and GC/MS. The water mass fraction can be reduced by 91.4 % (from 31.5 % to below 2.7 %), the viscosity by 65.8 % (from 36.5 to 12.5 cP) and the higher heating value can be increased by 96.8 % (from 3,918 to 7,712 kcal/kg), the pH by 1.3 (from 2.7 to 4.0). FT-IR and GC/MS analysis indicated that labile acids, aldehydes, ketones and lower alcohols were transformed to stable target products. Using this approach, the water content of the pyrolysis oil is reduced significantly. These improvements should allow the utilization of upgraded pyrolysis liquids in standard boilers and as fuel in CHP (Combined heat and power) plants.

• Journal of environmental and Sanitary engineering
• /
• v.5 no.1
• /
• pp.34-45
• /
• 1990

The purpose of this reserch is to investigate the flora of Dumi Island. This island locates at $128^{\circ}$ 13' E. longitude and $34^{\circ}$ 41' N. latitude. As a result of our investigation, the distribution of plants on Dumi Island could be summarized as follows. The vascular plants through this investigation were 66 families, 121 genera, 127 species, 16 varieties, 2 forma, and 145 kinds. From 1945 to 1960, most Pinus densiflora and Quercus mongolica were cut and sent as fuel to the cities of Masan, Chungmu and Samchunpo. After these deforestation years, there was a change of policy in the area and then wood was substituted by coal blacks as fuel and along with this occurs reforestation. Because of the reforestation by the present administration and natural means of suctrees, Castamopsis cuspidata var. thunbergii, Camellia japonica and Machilus japonica; they were found to exist near Sheonangdang in the northern region at Hakli and at Kuchun in the south. In the central part of the island at Mt. Chunhwang there are slopes of 20-30 degrees which are cultivated by the islanders this mountain which can be cultivated and 65% or 830 islanders are farming this land. Although this 125.4 hectors is not a large portion, this mountain with its variety of growth at different elevations, seems to be very fertile causing thick growth at any level.

• Journal of the Korean Institute of Rural Architecture
• /
• v.20 no.2
• /
• pp.49-56
• /
• 2018

The vernacular houses with 田-shaped floor plan at Gangreung have been played important roles in tracing the vernacular living cultures including housing life. But due to the adoption of convenient facilities in vernacular housing lives caused by modernization and urbanization, many changes and transformations have happened at residential space of vernacular houses. This thesis targets to extract basic data to prepare and prevent various problems in process of renovation, extension and function change as installing housing life facilities, and to identify the changes and transformations of them to prepare the proper balances between their original form preservation and residents' convenience living. The results are as follows. The inner wall removal of rooms, the fuel change of cooking and heating, the leveling change of kitchen floor made possible the sedentary lifestyles. And its residential rooms were transformed from two row to one row by inner wall removal, the fuel heating change, the heating method change and the heat insulating materials. The residential extension materials were changed from the traditional materials such as soil, wood, etc to the modern materials such as cement block or brick, sandwich panel, etc. And the modern materials were used and attached to widen residential spaces to the vernacular house because of the easiness of execution. So, it is necessary for 田-shaped floor plan vernacular house owners to distribute printed execution guide book to prevent and minimize the various problems to be shown by extension, renovation and function change.