• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.379-384
• /
• 1996

Thermal-hydraulic performance has been analyzed for an advanced reactor core loaded with hexagonal fuel assemblies. Currently available CHF prediction models and data base for triangular lattice bundles have been thoroughly reviewed, and as a result the KfK-3 CHF correlation with limit CHFR of 1.235 has been determined to be most appropriate. The pressure drop model in COBRA-IV-I code has been modified for the analysis of triangular lattice rod bundles. In view of maximizing the thermal margin, the geometry of a hexagonal fuel assembly, such as rod diameter and rod pitch, has been optimized with a fixed fuel assembly cross sectional area The optimum value of the moderator-to-fuel volume ratio is estimated to lie between 0.65 to 1 with 9.5 mm rod diameter. The thermal margin of these hexagonal fuel assemblies in the AP600 core has been evaluated and compared with that of square lattice fuel assemblies such as VANTAGE-5H and KOFA. The analysis result shows that the performances of hexagonal fuel assemblies are more favorable than the square fuel assemblies in the aspect of steady-state overpower margin.

• 시스템엔지니어링학술지
• /
• 제13권1호
• /
• pp.33-39
• /
• 2017

This paper describes the system engineering approach for the heat transfer analysis of plus7 fuel rod for APR1400 using, a commercial software, ANSYS. The fuel rod is composed of fuel pellets, fill gas, end caps, plenum spring and cladding. The heat is transferred from the pellet outward by conduction through the pellet, fill gas and cladding and further by convection from the cladding surface to the coolant in the flow channel. The goal of this paper is to demonstrate the temperature and heat flux change from the fuel centerline to the cladding surface when having maximum fuel centerline temperature at 100% power. This phenomenon is modelled using the ANSYS FEM code and analyzed for steady state temperature distribution across the fuel pellet and clad and the results were compared to the standard values given in APR1400 SSAR. Specifically the applicability of commercial software in the evaluation of nuclear fuel temperature distribution has been accounted. It is note that special codes have been used for fuel rod mechanical analysis which calculates interrelated effects of temperature, pressure, cladding elastic and plastic behavior, fission gas release, and fuel densification and swelling under the time-varying irradiation conditions. To satisfactorily meet this objective we apply system engineering methodologies to formulate the process and allow for verification and validation of the results acquired. The close proximity of the results obtained validated the accuracy of the FEM analysis of the 2D axisymmetric model and 3D model. This result demonstrated the validity of commercial software instead of proprietary in-house code that is more costly to develop and maintain.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(3)
• /
• pp.21-26
• /
• 1996

Recently several PWR Nuclear Plant experienced fuel rod fretting wear failures due to Flow Induced Vibration. When such multi-span supported fuel assembly has vibration excitation, it is important to know how fretting wears are progress and when the fuel rods are start to failure. In this study, we estimate the amount of wear depth using Archard theory when the fuel rod starts to relative motion against spacer grid dimples.

• Nuclear Engineering and Technology
• /
• 제25권3호
• /
• pp.424-429
• /
• 1993

핵연료 소결체가 장전되는 핵연료봉의 끝부분에는 각각의 핵연료봉을 구분해주는 고유의 문자가 인쇄되어 있다. 핵연료 집합체 제조 과정에서 각각의 핵연료봉은 고유 문자에 의해 구분되어 체계적으로 관리되고 있으며 아울러 핵연료 연소 이상상태 감시 및 사용후 핵연료 검사 분야에서 핵연료봉 제조과정 추적에 이용되고 있다. 핵연료봉 문자 자동인식은 핵연료 집합체 제조과정의 자동화를 위한 핵심 기술이다. 본 연구에서는 핵연료봉 문자인식 시스템을 개발하여, 핵 연료봉단에 기록된 각 문자로 부터 추출한 메쉬 특징값을 데이타베이스에 저장된 특정 문자의 특징값과 비교하여 자동으로 문자인식을 수행하도록 하였다. 실험 결과, 95.83 퍼센트의 양호한 인식률을 기록하였다.

• Nuclear Engineering and Technology
• /
• 제56권2호
• /
• pp.359-374
• /
• 2024

A high-fidelity numerical analysis methodology was proposed for evaluating the fuel rod cladding integrity of a Prototype Gen IV Sodium Fast Reactor (PGSFR) during normal operation and Design basis events (DBEs). The MARS-LMR code, system transient safety analysis code, was applied to analyze the DBEs. The results of the MARS-LMR code were used as boundary condition for a 3D computational fluid dynamics (CFD) analysis. The peak temperatures considering HCFs satisfied the cladding temperature limit. The temperature and pressure distributions were calculated by ANSYS CFX code, and applied to structural analysis. Structural analysis was performed using ANSYS Mechanical code. The seismic reactivity insertion SSE accident among DBEs had the highest peak cladding temperature and the maximum stress, as the value of 87 MPa. The fuel cladding had over 40 % safety margin, and the strain was below the strain limit. Deformation behavior was elucidated for providing relative coordinate data on each active fuel rod center. Bending deformation resulted in a flower shape, and bowing bundle did not interact with the duct of fuel assemblies. Fuel rod maximum expansion was generated with highest stress. Therefore, it was concluded that the fuel rod cladding of the PGSFR has sufficient structural safety margin during DBEs.

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2880-2886
• /
• 2020

A small leak occurring on the surface of a fuel rod due to damage exposes UO₂ to a steam atmosphere. During this time, fission gas trapped inside the fuel rod leaks out, and the gas leakage can be increased due to UO₂ oxidation. Numerous studies have focused on the steam oxidation and its thermodynamic calculation in UO₂. However, the thermodynamic calculation of the UO₂ oxidation in a pressurized water reactor (PWR) environment has not been studied extensively. Moreover, the kinetics of the oxidation of UO₂ pellet also has not been investigated. Therefore, in this study, the thermodynamics of UO₂ oxidation under steam injection due to a damaged fuel rod in a PWR environment is studied. In addition, the diminishing radius of the UO₂ pellet with time in the PWR environment was calculated through an experiment simulating the initial time of steam injection at the puncture.

• 대한기계학회논문집A
• /
• 제27권3호
• /
• pp.424-431
• /
• 2003

The spacer grid is one of the main structural components in the fuel assembly, which supports the fuel rods and maintains coolable geometry from an external load. A vibration test and a finite element analysis using ABAQUS on a dummy fuel rod continuously supported by Optimized H type(OHT) and New Doublet (ND) spacer grids arc performed to obtain the vibration characteristics such as natural frequencies and mode shapes an(1 to verify a finite element model. The results from the test and the finite element analysis are compared by modal assurance criteria (MAC) values. It is resulted that MACs for the first, the third and the fifth mode shapes are relatively good as compared with those of the second an(1 fourth ones. The natural frequency differences between two methods as well as the mode comparison results for the rod with OHT spacer grid are better than those with ND spacer grid. It is judged that the FE model for the ND spacer grid spring should be modified to consider the long contact length which actually happen when the spring supports the rod.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.1055-1058
• /
• 2005

In the ACPF(Advanced spent nuclear fuel Conditioning Process Facility), the spent fuel pellets which are highly radioactive materials are separated with its clad and are fed into the next conditioning process. For this, at the other facility called PIEF(Post Irradiation Examination Facility) a spent fuel rod, 3.5 m long, is cut by 25 cm long which is suitable length fur the decladding process. These rod-cuts are packed into the capsule and are moved to the ACPF. Once the capsule is unloaded in the ACPF, the rod-cut is taken out one-by-one from the capsule and installed on the decladding device. In these processes, the crushed spent fuel pellet can be scattered inside the facilities and thus it contaminate the hot cell. In this paper, we developed the specially designed capsule which prevents the pellets scattering and remarkably reduces the leading and unloading time of the rod-cuts.

• 대한기계학회논문집A
• /
• 제36권12호
• /
• pp.1653-1661
• /
• 2012

본 논문에서는 냉각유동에 의한 SMART 핵연료집합체의 압력강하변화 및 구조특성을 연구하였다. 난류 모델인 BSL 레이놀즈 응력 모델로서 냉각수의 유동을 모델링하여 유체고체연계 해석을 수행하였다. 우선, 지지격자체에 지지된 핵연료봉의 진동해석을 수행하여 실험 결과와 비교하였는데 실험에서의 고유진동수는 48 Hz 로서 시뮬레이션 값과 2% 의 오차를 발생하였다. 핵연료집합체의 압력강하는 한국원자력연구원에서 수행한 실험적 값과 비교하여 8%의 오차가 발생하였고 해석의 타당성을 증명하였다. 유체해석에서는 집합체를 통과하는 각 구간의 유체 속도와 이차유동에 의한 와류생성과정을 관찰하였다. 마지막으로 진동해석과 유체해석의 연계를 통하여 유체유발진동에 의한 연료봉의 변위 값을 관찰하고 최대 변위가 발생하는 곳의 변위 PSD 를 계산하였다.

• Nuclear Engineering and Technology
• /
• 제28권1호
• /
• pp.17-26
• /
• 1996

프레팅마모 기인 연료봉 손상을 방지할 수 있는 노내 연료봉 지지조건은 잔여 지지격자스프링 변위량 또는 연료봉 /지지격자 갭에 의해 평가될 수 있다. 핵연료 설계 인자들이 프레팅마모 손상에 미치는 영향을 평가하기 위해 연소도의 함수로서 노내 연료봉 지지조건을 모사할 수 있는 방법론을 사용하여 GRID-FORCE프로그램을 개발하였다. 이 프로그램에서는 노내 연료봉 지지조건에 영향을 주는 주요 인자로서 피복관 크립, 초기 스프링 변위, 초기 스프링힘 그리고 스프링힘 조사이완이 고려된다. 이 주요 인자들에 대한 민감도 분석 결과, 초기 스프링 변위, 스프링힘 조사이완, 피복관 크립 순으로 노내 연료봉 지지조건에 영향을 주는 것으로 나타났다. 이 프로그램을 실제 노내에서 발생한 프레팅마모 기인 연료봉 손상에 적용한 결과를 토대로 판단해 볼 때 이 프로그램을 새로 개발된 피복관 재질 및 /또는 새로 개발된 지지격자 설계가 프레팅마모 기인 연료봉 손상을 방지할 수 있는 설계여유도를 효과적으로 평가할 수 있음을 알 수 있다.