• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.88-95
• /
• 2002

Fretting of fuel rod cladding material, Zircaloy-4 Tube, in PWR nuclear power plants must be reduced and avoided. Nowadays the introduction of surface treatments or coatings is expected to bean ideal solution to fretting damage since fretting is closely related to wear, corrosion and fatigue. Therefore, in this study the fretting wear experiment was peformed using TiAIN coated Zircaloy-4 tube as the fuel rod cladding and uncoated Zircaioy-4 tube as one of grids, especially concentrating on the sliding component. Fretting wear resistance of TiAIN coated Zircaloy-4 tubes was improved compared with that of TiN coated tubes and uncoated tubes and the fretting wear mechanisms were delamination and plastic flow following by brittle fracture at lower slip amplitude but severe oxidation and spallation of oxidative layer at higher slip amplitude.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.400-405
• /
• 2001

Nozzle of the double-plated grid plays the role of the spring to support a fuel rod as well as to provide the coolant path in grid. The nozzle was known to be necessary to reduce the spring stiffness for supporting performance. In this study the contact analysis between the fuel rod and the nozzle type spacer grid was performed by using ABAQUS standard to propose the preferable shape in tenn of spring performance. Two small cuts at the upper and lower part of the nozzle appeared to have a minor effect in decreasing the nozzle stiffness. A long slot at the center of the nozzle was turned out not only to decrease the spring constant as desired but also to increase the elastic displacement.

• Journal of Mechanical Science and Technology
• /
• 제15권3호
• /
• pp.403-409
• /
• 2001

The main objective of the present study is to perform an experimental evaluation of five existing correlations for the subchannel pressure drop analysis of a wire-wrapped fuel assembly. For this purpose, a series of water experiments have been performed using a helical wire-wrapped 19-pin fuel assembly for various test parameters. Four different test sections with different pitch to rod diameter ratios (P/D) and wire lead length to rod diameter ratios (H/D) have been fabricated. A series of pressure drop measurements were made to obtain friction factors for these four test sections. The new data along with existing data are used to evaluate existing correlations. Both the original and the simplified Cheng and Todreas correlations give the best agreement with experimental data for all flow regions.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.453-458
• /
• 2001

The fretting wear of a nuclear fuel rod it a dangerous phenomenon. In this study, TiN coating was used to reduce the fretting wear of Zircaloy-4 tube, a nuclear fuel rod cladding material. TiN coating is probably one of the molt frequently and successfully used PVD coatings for the mitigation of fretting wear. The fretting tester was designed and manufactured for this experiment. The number of cycles, slip amplitude and normal load were selected as main factors of fretting wear. The results of this research showed that wear volume was improved 1.3∼3.2 times with TiN coating. The worn surfaces were observed by SEM. Wear mechanism at lower slip amplitude was the brittle cracks and rupture of TiN coating. However, adhesive and abrasive wear were mainly observed on most surfaces at higher slip amplitude.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2003년도 춘계학술발표대회 요약집
• /
• pp.260-260
• /
• 2003

• Nuclear Engineering and Technology
• /
• 제35권5호
• /
• pp.378-386
• /
• 2003

Recently failures of nuclear fuel rods in Korean nuclear power plants were reported and their failure causes have been investigated by using PIE techniques. Destructive and physico-chemical examinations reveal that the clad hydriding phenomena had caused the rod failures primarily and secondarily in each case. In this study, the basic mechanisms of the primary and the secondary hydriding failures are reviewed, PIE data such as cladding inner and outer surface oxide thickness and the restructuring of the fuel pellets are analyzed, and they are compared with the predicted behaviors by a fuel performance code. In addition, post-defected fuel behaviors are reviewed and qualitatively analyzed. The results strongly support that the hydriding processes, primary and secondary, played critical roles in the respective fuel rods failures and the secondary hydriding failure can take place even in the fuel rod with low linear heat generation rate.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2236-2241
• /
• 2008

The surface heat flux of nuclear fuel rod is the most important factor which can affect safety of reactor and fuel. If fuel rod surface heat flux exceeds the CHF(${\underline{C}}ritical$ ${\underline{H}}eat$ ${\underline{F}}lux$), fuel can be damaged. In case of double cooled annular fuel, which is under developing, contains two coolant channels. Therefore, a generated heat in the fuel pellet can move to inner or outer channel and heat flow direction is decided by both sides heat resistance which varied by dimension and material property change which caused by temperature and irradiation. The new program(called DUO) was developed. For the calculation of surface heat flux, a both sides convection by inner/outer coolant, s gap temperature jump and conduction in the fuel are modeled. Especially, temperature and time dependent fuel dimension and material property change are considered during the iteration. A sample calculation result shows that the DUO program has sufficient performance for annular fuel thermal hydraulics design.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.7-14
• /
• 1986

본 연구에서는 가압경수형 원자로심을 모의하는 3*3배열로 된 모의연료 봉다발의 실험장치를 이용하여 재완수과정의 유동특성과 열전달특성을 파악하였으며, 재완수과정중 연료봉의 온도거동을 예측하는 REFLUX코드를 최근 개발된 연구자료를 토대로 수정하여 본실험결과와 비교하였다.

• 한국CDE학회논문집
• /
• 제5권4호
• /
• pp.327-335
• /
• 2000

The spent fuel rod extracting machine is automatically operated in high radioactive environment, so high reliability of operation is required. In this paper, to enhance the reliability of this machine by providing a close monitoring capability. a real time graphic simulation method is suggested. This method utilizes conventional IGRIP (Interactive Graphics Robot Instruction Program) 3D graphic simulation tool to visualize and simulate the 3D graphic model of this machine. Also, the dedicated protocol is defined for transmission of the operational data of the machine. The real time graphic simulation is realized by developing the socket module between a graphic workstation and a machine control computer through the TCP/IP network and by dividing the 3D graphic simulation GSL(Graphic Simulation Language) program as a small sized sub routine. The suggested method is implemented while automatically operating the rod extracting machine. The result of implementation shows that the real time 3D graphic simulation is well synchronized with the actual machine according to the operational data.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1715-1718
• /
• 2005

During demonstrations of a process conditioning spent nuclear fuels, it may be necessary to transport and handle Spent fuel road cuts from Post Irradiation Examination facility to Slitting device in The hot cell. It may be not easy to transport spent fuel rod cuts because rod cuts are high radioactive materials. For this purpose, we have developed a capsule for transporting and handling high radioactive materials. We have analyzed conditions of a hot cell and requirements of the device, designed and manufactured The prototype of the device, and done some performance tests. From the tests, it has been shown that transportation and handling without scattering nuclear material was smooth but the weight of capsule was heavy. These result will be reflected to a design of the improved transportation and handling device which will be used during demonstrations.