• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.26-31
• /
• 2008

This experimental study investigates the local heat transfer enhancement characteristics and the associated frictional head loss in the rectangular channel with a single inclined baffle. Four different types of the baffle are used. The inclined baffles have the width of 19.8 cm, the square diamond of $2.55cm{\times}2.55cm$, and the inclination angle of 5o, and number of holes of up to 9. Reynolds number is varied between 23,000 and 57,000. Results show that the heat transfer and friction factor depend significantly on the number of baffle holes and Reynolds number. The friction factor decreases with increasing Reynolds number and the number of holes on the baffle. It is found that the heat transfer performance of baffle type II(3 hole baffle) has the best values.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.304-310
• /
• 2001

Flow pulsation often causes vibration and noise in piping systems and therefore has been a troublesome concern for fluid system engineers. According to frequency increase in this paper under the influence wave form of velocity in springly flow and viscosity are drop coefficient of viscosity become increase so that impedance and resistance. The transient variations of flow rate are measured by a modified impedance tube method which is realized by virtue of the present analytical technique. At pipe line in order to eliminate vibration, confirm happened intermittently impedance characteristics. We make a test and frequency analysis and have to minimize obstructive component at hydraulic circuit.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.196-202
• /
• 2006

This paper presents a case study on the tribological failure analysis of a clutch system for a manual transmission car. The clutch systems are composed of clutch disk, clutch pressure plate, flywheel rubbing surface, coil and diaphragm springs, release bearing and lever, clutch spline and shaft. The purpose of a clutch system is to transmit and disconnect the driving power of engines by frictional farce from a rubbing surface of a flywheel to a clutch disk and clutch pressure plate with a minimum power loss. In this study, many tribological failure cases based on the wear phenomena and thermal distortions have been presented, which are collected from the car repair shop and maintenance center. The triboiogicai failures are mostly come from the driving conditions, overloading of a car, and especially driving style and personal habit of a car driver.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.253-259
• /
• 1997

A software for design of turbine bearings has been developed based on both the theoretical analysis and experimental investigation. Static and dynamic performance, i.e. load capacity, frictional loss, temperature distribution, stiffness and damping coefficients, stability etc., can be obtained by using this software taking into account the effects of three dimensional variation of lubricant viscosity, turbulence and inlet pressure. A performance test rig was developed by self-design and technology, which was used to verify static and dynamic characteristics and to investigate the proper boundary conditions for theoretical analysis. Consequently HANJUNG has developed the self-design technology for design of turbine bearings for power plants.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.95-99
• /
• 1994

Robot engineering is developed mainly in the field of intelligibility such as a manipulation. Considering the popularization of robots in the future, however, a robot should be studied from a viewpoint of saving energy because a robot is a kind of machine with a energy conversion. This paper deals with minimizing an energy consumption of a manipulator which is driven in a point-to-point control method. When a manipulator carries a heavy payload toward gravitation or the links are de-accelerated for positioning, the motors at joints generate electric energy. Since this energy can be regenerated to the source by using a chopper, the energy consumption of a manipulator is only heat loss by an electric and a frictional resistance of the motors. The minimization of the sum of these losses is reduced Lo a two-points boundary-value problem of an non-linear differential equation. The solutions are obtained by the generalized Newton-Raphson method in this paper. The energy consumption due to the optimum angular velocity patterns of two joints of a two-links manipulator is compared with conventional velocity patterns such as quadratic and trapezoid.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.129-134
• /
• 2001

The paper presents the optimal design of a oil-free two-stage compressor, which is driven by 75 kW motor at an operating speed of 39,000 rpm, and the pressure ratio of which is up to 4. First, an attempt is made to obtain the optimal design of a bump bearing which supports a compressor rotor. Second, bump bearings and shaft are considered simultaneously, and the weighted sum of rotor weight and frictional torque is minimized. Finally, the optimal geometry of compressor wheel is considered. The mean efficiency and the - minimum efficiency are maximized respectively. The results presented in this paper provide important design information necessary to reduce the energy loss.

• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.314-321
• /
• 2004

Thermal distortion of non-contacting mechanical seals with inclined rubbing surfaces is affected by friction heat between seal ring and seal seat. The circulation fluid along the inclined rubbing surfaces maintains cooling friction heat and lubrication between the sealing surfaces of mechanical seal with an inclined surface. Mechanical seals with inclined sealing surfaces may be useful for reducing the frictional heating and power loss because of the introduction of cooling fluids to the sealing gap between seal ring and seal seat. From the FEM computed result shows that the thermal behavior and von Mises stress of sealing faces with an inclined angle 60 are much reduced in comparison of the conventional mechanical face seal with rectangular sealing surfaces.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.426-434
• /
• 2001

The hermetic reciprocating compressor driven by the BLDC motor rotating with variable speeds, is modelled and analyzed for dynamic characteristics. The governing equations of piston, connecting rod and crank-shaft of the reciprocating compression mechanism and characteristics of driving torque of the motor are obtained. Dynamic behavior of the crankshaft supported on 2 journal bearings is analyzed considering compression load and eccentric unbalance for the 4 rotating speeds of crankshaft. And. reaction forces generated from oil film in the journal bearings are analyzed under transient condition using Reynolds' equation. To take into account the dynamic characteristics depending on the variable rotating speeds, comparison on the dynamic behavior of crank-shaft is made for the 4 operating modes of the compressor. Results show that the magnitude of crankshaft locioperating on the lower rotating speeds is more larger than the higher ones due to reduction of inertia force of the reciprocating piston.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.87-92
• /
• 1995

Lip seals, important components in many hydraulic devices, dissipate energy through friction, resulting in power loss. This study contributes to an understanding of lip seal friction by further exploring the connections between friction behavior, viscoelastic properties of robber and viscous properties of the lubricant. Experiments haven been conducted for short stroke oscillations, where these connections are quite strong. Sliding friction experiments at a variety of pressures, temperatures and oscillation rates (for different seal materials, surface roughnesses and lubricant viscosities) are examined. Speculative explanations are suggested for conditions under which friction maxima and frictional vibrations occur.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.466-470
• /
• 2000

Externally pressurized air journal bearing has been widely used in high-speed spindle system and precision machinery because of its characteristics such as substantially low frictional loss, low heat generation and averaging effect leading better running accuracy. But air journal bearing have a disadvantage of the low load capacity due to the low viscosity. In this paper, The air journal bearing design to overcome the defects of air bearing such as low stiffness and dimping coefficients was investigated theoretically.