• 한국유체기계학회 논문집
• /
• 제6권2호
• /
• pp.7-14
• /
• 2003

This paper describes reliability characteristics of an air foil journal bearing for high-speed turbomachinery at a room temperature. To verify the reliability of air foil journal bearing, lift-off characteristics, load carrying capacity, and 10,000 cycle start-stop test were performed with a motor-driven test rig. A lift-off test shows the relationship between the rotating speed of the shaft and the frictional torque with bearing surface. About a load-carrying capacity, the tested air foil journal bearing produced a load capacity of 500N at an operating speed of 15,000rpm, which is compared with results of numerical analysis and empirical coefficients. Finally, the trends in change of start torque, stop torque, and bearing temperature were shown during a 10,000-cycle start-stop test of an air foil journal bearing. We found that an air foil bearing performs well, as a supported bearing for the high-speed turbocompressor.

• KSTLE International Journal
• /
• 제2권2호
• /
• pp.146-149
• /
• 2001

Recently, laser printers have been developed to have high-speed laser scanner with hydrodynamic bearings. Among the bearings, herringbone grooved bearing (HGB) produces hydrodynamic pressure by high-speed rotating and so make the surfaces between the shaft and sleeve separated. Accordingly, the bearings with non-contact rotation are suitable to high-speed rotating and have long bearing life and reliability. HGB is a kind of journal bearing and uses oil for a lubricant. HGB has excellent stiffness and load carrying capacity. Also, HGB is leakage-free due to groove pumping action. Consequently, HGB is valuable to be applied to high-performance devices such as hard disk drive, copier, and so on.

• KSTLE International Journal
• /
• 제2권2호
• /
• pp.127-132
• /
• 2001

The steady state performance of the counterrotating floating ring journal bearings is analyzed with isothermal finite bearing theory. The effect of counterrotating speed of the sleeve on the performance of the bearing is investigated. It is shown that counterrotating floating ring journal bearings can have considerable load capacity at the same counterrotating speeds, while conventional circular journal bearings with one fluid film cannot. Investigating the relationship between the frictional torques exerted on the ring due to the inner and outer films and the rotational speed of the ring, the stability of the equilibrium state is identified and the operating characteristics of the counterrotating floating ring journal bearing according to the method of acceleration or deceleration of the rotational speeds of the journal and sleeve are clarified. It is theoretically confirmed that floating ring journal bearings can be used in counterrotating journal-bearing system and become good substitutes for rolling bearings in counterrotating systems.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.28-34
• /
• 1996

The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.73-79
• /
• 1999

Finite element equations by using fast Fourier transformation were formulated for studying temperatures resulting from frictional heating in sliding systems. The equations include the effect of velocity of moving components. The program developed by using FFT-FEM that combines Fourier transform techniques and the finite element method, was applied to the sliding bearing system. Numerical prediction obtained by FFT-FEM was in an excellent agreement of experimental temperature measurements.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.65-73
• /
• 1998

A dynamic analysis and friction loss of non-variable swash plate compressor are studied theoretically. Rotating swash plate and reciprocating pistons are modelled kinematically, and forces and torques acting on rotor-bearing system are analyzed. Then, friction losses on 4 roller bearings, 10 sliding parts between swash plate and shoes, and 10 lubricating surfaces between cylinders and pistons are calculated. On each frictional element of sliding surfaces and roller bearings, the same friction loss is obtained, respectively.

• Tribology and Lubricants
• /
• 제17권2호
• /
• pp.97-108
• /
• 2001

This paper describes the development of performance analysis technique for a leaf-type gas lubricated fail bearing. Stiffness coefficient and frictional damping due to the slip between all contacts of leaves are evaluated for various leaf structures. The fluid film thickness and pressure distribution are computed but it is not considered the elastic deformation by film pressure. The analysis results include the effects that the curvature radius and the length of leaf and the friction coefficient have on the static and dynamic characteristics of the foil bearings.

• Tribology and Lubricants
• /
• 제16권3호
• /
• pp.218-222
• /
• 2000

Finite element equations by using fast Fourier transformation were formulated for studying temperatures resulting from frictional heating in sliding systems. The equations include the effect of velocity of moving components. The program developed by using FFT-FEM that combines Fourier transform techniques and the finite element method, was applied to the sliding bearing system. Numerical prediction obtained by FFT-FEM was in an excellent agreement of experimental temperature measurements.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.86-93
• /
• 1996

The lubrication characteristics of high-speed ball bearings has been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flowrates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 303 kgf axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.225-232
• /
• 1999

Construction case of PRD (Percussion Rotary Drill) pipe pile and matters to be attended in construction of PRD pile were reviewed. The compressive and uplifting static pile load tests for PRD piles were performed and, also, analysis by Pile Driving Analyzer was done. Based on these results, bearing components in each resisting part (that is: steel toe, external skin, and internal skin) were measured separately. The measured resisting force was compared to the value calculated by the estimated formula. The pile capacity was mobilized in steel toe area and the external skin friction and the internal friction were not produced. Thus, it could be considered that toe of PRD pile should be supported in hard bearing stratum (for example, the fresh soft rock).