• Journal of computational fluids engineering
• /
• v.11 no.1 s.32
• /
• pp.43-51
• /
• 2006

A fluid transient analysis on the Koreasat 1 & 2 pipeline system is conducted through numerical parametric studies in which unsteady friction results are compared with quasi-steady friction results and show relatively accurate prediction of the response curve with the unsteady friction. The code developed and used in this analysis has finished verification through comparing with the original Zielke model, the full and recursive convolution model and quasi-steady model as a reference. The unsteady friction is calculated by the recursive convolution Zielke model in which a complete evolution history of velocity field is no longer required so that it makes the fluid transient analysis on the complicated system possible. The results show that the application of quasi-steady friction to model cannot predict the entire response curve properly except the first peak amplitude but the application of unsteady friction to model can predict reasonably the response curve, therefore it is to know the characteristics of the propulsion system.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.772-779
• /
• 2000

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with a different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused a abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.241-250
• /
• 2010

A recurrent adaptive model-free intelligent control with a friction estimation law is proposed to enhance the positioning performance of the mover in PMLSM system. For the PMLSM with nonlinear friction and uncertainty, an adaptive recurrent fuzzy neural network(ARFNN) and compensated control law in $H_{\infty}$ performance criterion are designed to mimic a perfect control law and compensate the approximated error between ideal controller and ARFNN. Combined with friction observer to estimate nonlinear friction parameters of the LuGre model, on-line adaptive laws of the controller and observer are derived based on the Lyapunov stability criterion. To analyze the effectiveness our control scheme, some simulations for the PMLSM with nonlinear friction and uncertainty were executed.

• 한국전산유체공학회:학술대회논문집
• /
• 2006.05a
• /
• pp.320-323
• /
• 2006

A fluid transient analysis on the Koreasat 1 & 2 pipeline system is conducted through numerical parametric studies in which unsteady friction results are compared with quasi-steady friction results and show relatively accurate prediction of the response curve with the unsteady friction. The code developed and used in this analysis has finished verification through comparing with the original Zielke model, the full and recursive convolution model and quasi-steady model as a reference. The unsteady friction is calculated by the recursive convolution Zielke model in which a complete evolution history of velocity field is no longer required so that it makes the fluid transient analysis on the complicated system possible. The results show that the application of quasi-steady friction to model cannot predict the entire response curve properly except the first peak amplitude but application of unsteady friction to model can predict reasonably he response curve, therefore it is to know the characteristics of the propulsion system.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.261-261
• /
• 2000

This paper analyzes the characteristics of pre-sliding friction of an X-Y table of CNC machining center at velocity reversal, and presents a simple and effective method of friction compensation based on this characteristics. At velocity reversal, a large position tracking error occurs because of the discontinuous change of friction. The relationship between the occurrence time of maximum position tracking error and the acceleration at zero velocity is analyzed by using the spring-like friction model. Furthermore, the experimental observation verifies this relation. From this, the state transition tine from pre-sliding regime into sliding regime can be predicted. Using the predicted transition time, the friction can be effectively compensated and table experimental results show its effectiveness.

• Tribology and Lubricants
• /
• v.8 no.2
• /
• pp.7-13
• /
• 1992

Wear experiments were conducted using the SRV machine on the lubricated conditions of the several temperature and load. Oil samples were prepared by adding several friction modifiers into both paraffinic base oil and engine oil. Friction and wear characteristics of the oils were determined and are discussed in connection with the friction modifiers contained, the testing temperature and the load applied. From the study, it was found the MoDTC and the MoDTP, added into the engine oil, caused drastic increase in wear and had a tendendy to lose the friction-reducing property on some specific conditions of temperature and/or load, though they had the good property on other conditions. Ashless friction modifiers and dispersed $MoS_2$ investigated showed the good friction-reducing property, but the loads, where they became active, were different.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.417-426
• /
• 2001

The effect of silver particle introduction on the rolling friction of AISI 52100 steel pairs has been investigated. Experiments ware performed in dry conditions using a thrust bearing-type rolling test rig at a load range of 12-960 N and a sliding velocity range of 8-785 mm/sec with pure (99.99%) silver particles. Results showed that introduced silver particles formed transfer layers, which protected the virgin bearing surfaces and resulted in the low lolling friction. By changing the quantity of silver particles, transitions in the rolling friction were found. Results also showed that the variations in normal load and rolling speed also affected the rolling friction behavior. Analyses of SEM and EPMA showed that the formation the transfer layer was mainly governed by the silver particle quantity, normal load and rolling speed, and this resulted in the different behavior of rolling friction. In this study, it was found that the low and stable rolling friction was resulted from the, shakedown phenomena occurred at the silver transfer layer.

• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.265-269
• /
• 2009

The wear of the contact in the tappet accounts for the greatest portion of entire friction loss of an engine, leading to the occurrence of abnormal wear. The coated specimens for earn-tappet wear test were producted by using PVD-Sputtering coating method. It examined the friction characteristics occurring between the earn and the tappet by using the dedicated wear tester and found that the friction torque value was reduced through comparison testing with the existing part when the low friction coating was applied. So application of the low friction coating to actual vehicles will reduce the fuel economy and occurrence of noise-vibration.

• Fashion & Textile Research Journal
• /
• v.2 no.5
• /
• pp.443-449
• /
• 2000

An investigation of the relative velocity of friction surface for the newly developed cone drum twister texturing mechanism is reported. The cone drum twister is one of the outer surface contacting friction-twisting devices in false-twist texturing. In this cone drum twister, a filament yam passes over the surface of the cone drum that rotates by passing the yarn without a special driving device. This research is theoretically composed of the analysis of the false twisting mechanism. The equations were derived by using the conical angle of the cone drum, projected wrapping angle, and yarn helix angle. Theoretical values of the relative velocity of friction surface were calculated and discussed. It is shown that, as the projected wrapping angle increased, the relative velocity of friction surface decreased. But as the conical angle increased the relative velocity of friction surface also increased.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.6
• /
• pp.657-664
• /
• 2008

This research compared several unsteady friction models for transient analysis of pipeline system. Unsteady friction is an important factor for accurate simulation of hydraulic transient. Steady friction, quasi-steady friction, Zielke's model and two versions of Brunone model were compared with measurement data of identical pipeline conditions. This study showed that the existing simple steady friction model can be useful for the safer design of pipeline system due to its overestimation of waterhammer, but introduction of more elaborate models are required for advanced analysis such as inverse transient analysis of friction or leakage and the preliminary analysis of water quality prediction of water distribution system.