• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.181-182
• /
• 2010

• Tribology and Lubricants
• /
• 제24권1호
• /
• pp.44-48
• /
• 2008

The wear characteristics of the gold alloy dental prosthesis have been investigated. The wear tests were performed by using a pin-on-disk wear tester at room temperature. Vickers hardness and fracture toughness measurement of dental materials were preformed. Microscopic observations on worn surfaces of specimens were conducted by microscope. The friction coefficient of the gold alloy dental prosthesis was investigated according to weight and slinging velocity. The hardness of the gold alloy dental prosthesis were similar and a half of the enamel of natural teeth.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.382-391
• /
• 2001

This paper presents tribological results of the screw materials, which include the conventional screw and newly developed one. The tribotreated screw is manufactured by applying the polymer power to the heat treated surface of the screw. The injection pressure which is developed between the screw and the cylinder has been applied to the rubbing surface of the specimen in a pin-on-disk wear tester. The measured results show that the friction coefficient and wear rate of a tribotreated screw are low compared to the conventional one.

• 한국산업융합학회 논문집
• /
• 제19권4호
• /
• pp.185-192
• /
• 2016

Low operational cost and high efficiency is absolute requirements in the mass production of the ship engine. Increasing the performance of the fuel injection system in the diesel engine is one kind of solution to improve the efficiency. Modern diesel engines are using electronic control module as the main controller in the fuel injection control system, however the mechanical system still involved in the modern control system. In modern ship engine, a control valve was used in injection fuel to regulate the flow of the fuel. High pressure and friction are intensively occur within this part, therefore high wear resist and low friction coefficient material including fine lubricating are needed. This study is to figure out the wear resist material and proper lubricant in the control valve fuel injection. The experiment has been tested using pin on disk in several treatments those are used various lubricants and non-lubricant condition. Two kinds of lubricant were used in this experiment such as INDERIN AW-32 and paraffin oil. INDERIN AW-32 has a better result compared to non-lubricant condition, which are 20% performance increases than non-lubricant condition. SCM 440 was providing small friction coefficient in the lower velocity. The friction coefficient was constantly maintains at 0.1 m/s of velocity or above respectively with the increment of the loads. Using INDERIN AW-32 and paraffin oil the lowest friction coefficient occurred at the lower load, and increases side by side with the increment of loads.

• 대한기계학회논문집B
• /
• 제39권6호
• /
• pp.535-540
• /
• 2015

등판이 기울어지는 사무용 의자에서 등판 회전축 위치를 인체의 엉덩관절에 일치시키면 인체와 등판이 일체화되어 기울어짐으로써 사용성을 향상시킬 수 있다. 그러나 등판 힌지가 외부로 돌출되지 않도록 하기 위해 적용되는 핀인슬롯 조인트에서 기구적인 마찰이 발생해 등을 기울이고 세우는 동안 사용자에 영향을 줄 것으로 예상된다. 본 연구에서는 마찰 정도가 다른 조인트 부품으로서 슬라이더, 롤러 그리고 베어링 세 가지 유형을 적용하고, 등판 기울임 시 대비 복귀 시의 반발력 비율을 측정하였다. 실험 결과 베어링, 롤러, 슬라이더를 적용한 경우 등판 반발력 비율은$[{\pm}SD]$은 각각 $59.7[{\pm}10.3]%$, $47.2[{\pm}13.6]%$, $30.3[{\pm}18.1]%$로 나타나 베어링을 적용할 경우 마찰이 가장 작았다. 그러나 각 부품들은 생산단가 측면에서 차이를 보이기 때문에 부품 선정 시 마찰감소 성능뿐만 아니라 사용자의 주관적인 만족도를 함께 고려할 수 있음을 제시하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.319-320
• /
• 2002

Numerical simulation of chip formation during high speed machining requires knowing the friction at tool/chip interface. This parameter is hardly identified and generally the loadings (temperature, force) during the identification are not similar to those encountered during machining. Thus, Coulomb friction identified with pin-on-disc device is often used to conduct numerical simulation. The used of this technique cannot leads to good numerical results of chip formation compared to the experimental tests especially in the case of low uncut chip thickness. In this contribution, we propose a new method to evaluate the friction at tool/chip interface. In fact several Coulomb friction parameters are identified corresponding to several parts of the cutting tool. Experimental tests have been conducted allowed us to determinate both the level and the distribution of the Coulomb friction. Experimental results are also compared to the results of orthogonal cutting simulation. We show that this technique allows predicting accuracy results of chip formation.

• 한국정밀공학회지
• /
• 제24권1호
• /
• pp.79-84
• /
• 2007

Some surface pattern of tribological application is an attractive technology of engineered surface. Therefore, friction reduction is considered to be necessary for improved efficiency of machine. This study investigated the effect of friction property for angles of micro-crosshatch groove surface pattern on bearing steel using pin-on-disk test. We obtain sample which can be fabricated by photolithography process. We discuss the friction property depend on an angle of crosshatch groove surface pattern. We can verify the lubrication mechanism as Stribeck curve, which has a relationship between the friction coefficient and a dimensionless parameter under the lubrication condition. It was found that the friction coefficient was related to angle of crosshatch groove pattern on contact surface.

• 한국기계가공학회지
• /
• 제10권3호
• /
• pp.94-99
• /
• 2011

Micro-scale surface pattern has an benefit of tribological application under lubricated sliding contact. Therefore, a special pattern, that has to reduce the coulomb friction under contact, is considered to be necessary for improved efficiency of machines. The current study investigated the friction property of angle effect for micro-scale grooved crosshatch pattern on bearing steel surface using pin-on-disk type. The samples fabricated by photolithography process and then these are carry out the electrochemical etching process. We discuss the friction property due to the influence of hatched-angle on contact surface. We could be explained the lubrication mechanism for a Stribeck curve. It was found that the friction coefficient depend on an angle of the crosshatch on contact surface. It was thus verified that micro-scale crosshatch grooved pattern could affect the friction reduction.

• 한국소음진동공학회논문집
• /
• 제24권4호
• /
• pp.332-338
• /
• 2014

Experimental study is conducted for investigating the characteristics of friction-induced noise with respect to the variation of system geometry. In this study, a vertically fixed rod is in contact with the reciprocating plate which is controlled by the step motor. Friction noise is generated during the reciprocating motion due to the frictional contact between the plastic pin and the aluminum plate. The frequencies of the friction noise are changed when the height of the rod varies. However, it is found that the vibration modes involved in the friction noise are not changed. It implies that the unstable modes remain unstable regardless of the change of the system geometry, and thus, there are the certain mode shapes which are likely to produce friction noise.

• Tribology and Lubricants
• /
• 제8권1호
• /
• pp.48-55
• /
• 1992

The friction characteristic of plastics (PTFE, Nylon, Acetal and phenolic) was studied on the lubricated condition with a pin on disk machine. Mineral oil without additive (base oil) and water were used as liquid lubricants at the controlled temperature. From the experimental work, it was found out that the coefficient of friction of plastics was controlled by the mechanical properities of plastic more than that of liquid for various load and temperature. Viscosity of liquid has affected on the friction only at low temperature under lighb load. Among the tested plastics, the coefficient of friction of PTFE was the lowest under light load and at low temperature while Nylon at medium load and temperature, and Acetal at heavy load and high temperature. The coefficient of friction of soft plastics like PTFE and Nylon were increased as the load and temperature were increased, while that of hard plastic (Acetal) was decreased and that of thermo setting plastic (phenolic) was mixed. Also for soft plastics, the coefficient of friction under heavy load was always higher than that under light load, while hard plastic was vice versa.