• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.2
• /
• pp.58-64
• /
• 2008

In this paper, we proposed the methodology of interference analysis based on monte-carlo method for effective use of Industrial, Scientific, Medical (ISM) band. The interference scenario is divided according to the distance and density. The simulation of interference analysis evaluates the interference probability according to distribution density of Interfering Transmitters (It) in the Secure Interference Area (SIA). The SIA is gained from the Interference Efficiency Range that satisfied to Interference Permissible Range of Victim Receiver (Vr). Simulation result that apply the proposed interference scenario to the WLAN and bluetooth, Interference Permissible Range was 60~400m. And the WLAN was acceptable within interference permissible range to six bluetooth that exist in the SIA. In the same condition, when applied Listen Before Talk (LBT) based on Cognitive Radio (CR) to the bluetooth using Frequency Hopping (FH), interference probability was decreased sharply. The Spectrum Engineering Advanced Monte Carlo Analysis Tool (SEAMCAT) that has been developed based on the monte-carlo method by European Radio-communications Office (ERO) were used to the interference simulation.

• Journal of the Korean Society of Tobacco Science
• /
• v.25 no.1
• /
• pp.53-58
• /
• 2003

This study deals with the leaf tobacco assignment problem of a leaf tobacco warehouse with multiple input points and single output point. Also, the number of storage frequences is not necessary the same as that of retrieval for each leaf tobacco. A mathematical model is developed with the objective of minimizing the total travel distance associated with storage and retrieval operations. We also develop several heuristics based on the retrieval order frequency, retrieval/storage frequency ratio of leaf tobacco, and ABC curve. It is observed that the ABC curve based heuristic gives the best solution which is near optimal. Based on the test results from real world data, the ABC curve based heuristic is found to give a best performance. Comparing to current assignment method, the ABC curve based heuristic reduced total travel distance about 17.2%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.863-869
• /
• 2007

An improved method based on a normal frequency response function (FRF) is proposed to identify structural parameters such as mass, stiffness and damping matrices directly from the FRFs of a linear mechanical system. The method for estimating structural parameters directly from the measured FRFs of a structure is presented. This paper demonstrates that the characteristic matrices are extracted more accurately by using a weighted equation and eliminating the matrix inverse operation. The method is verified for a four degree-of-freedom lumped parameter system and an eight degree-of-freedom finite element beam. Experimental verification is also performed for a free-free steel beam whose size and physical properties are the same as those of the finite element beam. The results show that the structural parameters, especially the damping matrix, can be estimated more accurately by the proposed method.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.5 s.72
• /
• pp.36-41
• /
• 2006

The main object of this study is to develop an accurate and convenient method for the response analysis of offshore structures in real sea states. A numerical procedure is described for predicting the motion responses and tension variations of the ISSC TLP in multi-directional irregular waves. The developed numerical approach in the frequency domain is based on acombination of the three dimensional source distribution method, the dynamic response analysis method, and the spectral analysis method. Frequency domain analysis in the multi-directional irregular waves is expanded to a time domain analysis by using a convolution integral after obtaining the impulse response by Fourier transformation. The results of the comparison between responses in the frequency and time domain confirmed the validity of the proposed approach.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.15 no.5
• /
• pp.1610-1629
• /
• 2021

Failures frequently occurred in manufacturing machines due to complex and changeable manufacturing environments, increasing the downtime and maintenance costs. This manuscript develops a novel deep learning-based method named Multi-Domain Convolutional Neural Network (MDCNN) to deal with this challenging task with vibration signals. The proposed MDCNN consists of time-domain, frequency-domain, and statistical-domain feature channels. The Time-domain channel is to model the hidden patterns of signals in the time domain. The frequency-domain channel uses Discrete Wavelet Transformation (DWT) to obtain the rich feature representations of signals in the frequency domain. The statistic-domain channel contains six statistical variables, which is to reflect the signals' macro statistical-domain features, respectively. Firstly, in the proposed MDCNN, time-domain and frequency-domain channels are processed by CNN individually with various filters. Secondly, the CNN extracted features from time, and frequency domains are merged as time-frequency features. Lastly, time-frequency domain features are fused with six statistical variables as the comprehensive features for identifying the fault. Thereby, the proposed method could make full use of those three domain-features for fault diagnosis while keeping high distinguishability due to CNN's utilization. The authors designed massive experiments with 10-folder cross-validation technology to validate the proposed method's effectiveness on the CWRU bearing data set. The experimental results are calculated by ten-time averaged accuracy. They have confirmed that the proposed MDCNN could intelligently, accurately, and timely detect the fault under the complex manufacturing environments, whose accuracy is nearly 100%.

• Journal of Power Electronics
• /
• v.8 no.1
• /
• pp.91-100
• /
• 2008

The d-q harmonic detecting algorithms are dominant methods to generate current references for active power filters (APF). They are often implemented in the synchronous frame and time domain. This paper researches the frequency characteristics of d-q synchronous transformations, which are closely related to the analysis and design issues of control system. Intuitively, the synchronous transformation is explained with amplitude modulation (AM) in this paper. Then, the synchronous filter is proven to be a time-invariant and linear system, and its transfer function matrix is derived in the stationary frames. These frequency-domain models imply that the synchronous transformation has an equivalent effect of frequency transformation. It is because of this feature, the d-q method achieves band-pass characteristics with the low pass filters in the synchronous frame at run time. To simplify these analytical models, an instantaneous positive-negative sequence frame is proposed as expansion of traditional symmetrical components theory. Furthermore, the synchronous filter is compared with the traditional bind-pass filters based on these frequency-domain analytical models. The d-q harmonic detection methods are also improved to eliminate the inherent coupling effect of synchronous transformation. Typical examples are given to verify previous analysis and comparison. Simulation and experimental results are also provided for verification.

• KIISE Transactions on Computing Practices
• /
• v.22 no.10
• /
• pp.513-520
• /
• 2016

As IoT devices become more common in the public sphere, the energy efficiency of embedded systems becomes a problem of major interest in addition to the system performance. Energy efficiency is important for portable embedded systems because they obtain power from their battery, and a low energy efficiency will result in a low usage time while a high energy efficiency will allow for longer usage time. In this paper, we propose a memory usage based frequency selection method to improve the energy efficiency of embedded Linux systems by using devfreq to select the device's system frequency. In our experiments, we found that the proposed method reduces energy consumption in an embedded device by up to 18%.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1939-1949
• /
• 2016

This paper presents an alternative frequency adaptive grid synchronization technique named HDN-FLL, which can accurately extract the fundamental positive- and negative-sequence components and interested harmonics in adverse three-phase grid voltage. The HDN-FLL is based on the harmonic decoupling network (HDN) consisting of multiple first order complex vector filters (FOCVF) with a frequency-locked loop (FLL), which makes the system frequency adaptive. The stability of the proposed FLL is strictly verified to be global asymptotically stable. In addition, the linearization and parameters tuning of the FLL is also discussed. The structure of the HDN has been widely used as a prefilter in grid synchronization techniques. However, the stability of the general HDN is seldom discussed. In this paper, the transfer function expression of the general HDN is deduced and its stability is verified by the root locus method. To show the advantages of the HDN-FLL, a simulation comparison with other gird synchronization methods is carried out. Experimental results verify the excellent performance of the proposed synchronization method.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.8
• /
• pp.426-432
• /
• 2004

This paper presents a systematic approach of measurement, modeling and analysis of grounding system impedance in the field of lightning protection system and intelligent power equipments. The measurement and analysis system of ground impedance is based on a computer aided technique. The magnitude and phase of ground impedance were determined by the novel measurement and analysis using the revised fall-of-potential method. The ground impedances of the ground rod of 50 m long are considerably dependent on the frequency. The ground impedance is mainly resistive in the frequency range of 3-20 kHz. At higher frequencies, the reactive components of the ground impedances are no longer negligible and the inductance of the ground rod was found to be the core factor deciding the ground impedance. Although the steady-state ground resistance of the ground rod of 50 m was less than that of the ground rod of 10 m, the ground impedances of the ground rod of 50 m over the frequency range of more than 60 kHz were much greater than those of the ground rod of 10 m. Furthermore, the equivalent circuit model based on the measured data was proposed. and the calculated results were in approximately agreement with the measured data.

• Structural Engineering and Mechanics
• /
• v.89 no.6
• /
• pp.589-599
• /
• 2024

This study presents the usability of the high-rate single-frequency Precise Point Positioning (SF-PPP) technique based on 20 Hz Global Positioning Systems (GPS)-only observations in detecting dynamic motions. SF-PPP solutions were obtained from post-mission and real-time GNSS corrections. These include the International GNSS Service (IGS)-Final, IGS real-time (RT), real-time MADOCA (Multi-GNSS Advanced Demonstration tool for Orbit and Clock Analysis), and real-time products from the Australian/New Zealand satellite-based augmentation systems (SBAS, known as SouthPAN). SF-PPP results were compared with LVDT (Linear Variable Differential Transformer) sensor and single-frequency relative positioning (SF-RP) solutions. The findings show that the SF-PPP technique successfully detects the harmonic motions, and the real-time products-based PPP solutions were as accurate as the final post-mission products. In the frequency domain, all GNSS-based methods evaluated in this contribution correctly detect the dominant frequency of short-term harmonic oscillations, while the differences in the amplitude values corresponding to the peak frequency do not exceed 1.1 mm. However, evaluations in the time domain show that SF-PPP needs high-pass filtering to detect accurate displacement since SF-PPP solutions include trends and low-frequency fluctuations, mainly due to atmospheric effects. Findings obtained in the time domain indicate that final, real-time, and MADOCA-based PPP results capture short-term dynamic behaviors with an accuracy ranging from 3.4 mm to 8.5 mm, and SBAS-based PPP solutions have several times higher RMSE values compared to other methods. However, after high-pass filtering, the accuracies obtained from PPP methods decreased to a few mm. The outcomes demonstrate the potential of the high-rate SF-PPP method to reliably monitor structural and earthquake-induced ground motions and vibration frequencies of structures.