• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.8 s.113
• /
• pp.848-856
• /
• 2006

This paper describes the aeroelastic stability test of the small-scaled 'Next-generation Blade(NRSB)' with NRSH (next-generation hub system) and HCTH hingeless hub system in hover and forward flight conditions. Excitation tests of rotor system installed in GSRTS (general small-scale rotor test system) at KARI (Korea Aerospace Research Institute) were carried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(moving block analysis) technique was used for the estimation of lead-lag damping ratio. First, NRSB-1F blades with HCTH hub system, then NRSB- 1F with NRSH hub system were tested. Second, NRSB-2F blades with NRSH hub system were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Non-rotating natural frequencies, non-rotating damping ratios and rotating natural frequencies were showed similar level for each cases. Estimated damping ratios of NRSB-1F, NRSB-2F with HCTH and NRSH were above 0.5%, and damping ratio increased by collective pitch angle increasement. Furthermore damping ratios of NRSB-2F were higher than damping ratios of NRSB-1F in high Pitch angle. It was confirmed that the blade design for noise reduction would give observable improvement in aeroelastic stability compared to paddle blade and NRSB-1F design.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.81-89
• /
• 2019

In this study, wind tunnel test on Quad-Tilt Propeller which has tandem wings is carried out to analyze the aerodynamic interference effect of front wing and propeller on rear wing during forward flight. Using 6-axis balance system, forces and moments of whole aircraft were measured and using strain gauge at wing root, bending moments were measured to observe change of aerodynamic force of each wings. A 12-hole probe was used to measure the flow field in the wing and propeller wake. Flow characteristics were observed qualitatively through flow visualization experiment using tuft and smoke. To measure the aerodynamic interference by elements, the influence of front wing and propeller on rear wing was analyzed by changing the wings and propellers mount combination.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.249-251
• /
• 2022

In this paper, we present machine learning to control drone flight using EEG signals. We defined takeoff, forward, backward, left movement and right movement as control targets and measured EEG signals from the frontal lobe for controlling using Fp1. Fp2 Fp2 two-channel dry electrode (NeuroNicle FX2) measuring at 250Hz sampling rate. And the collected data were filtered at 6~20Hz cutoff frequency. We measured the motion image of the action associated with each control target open for 5.19 seconds. Using Matlab's classification learner for the measured EEG signal, the triple layer neural network, logistic regression kernel, nonlinear polynomial Support Vector Machine(SVM) learning was performed, logistic regression kernel was confirmed as the highest accuracy for takeoff and forward, backward, left movement and right movement of the drone in learning by class True Positive Rate(TPR).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.159-164
• /
• 2016

This paper reports the load factor logic design for a fly-by-wire helicopter flight envelope protection. As a helicopter is very complex system with a rotor, fuselage, engine, etc., there are many constraints on the flight region. Because of these constraints, pilots should consider them carefully and have a heavy workload, which causes controllability degradation. In this respect, automatic logic is needed to free the pilot from these considerations. As one of these logics, the flight envelope protection logic for the load factor of a FBW helicopter was designed. The flight to exceed the load factor is caused by an abrupt pitch cyclic stick change. In this scheme, the load factor limit logic was added between the pilot stick command block and pitch attitude command block. From the current load value, the available attitude range was calculated dynamically and simulated on the helicopter simulator model to verify the performance. A comparison of the simulation results at the hovering and forward speed region with and without applying the load limiting logic showed that the load factor limit was exceeded more than 20% when the logic was not applied, whereas with the load factor limit logic the load factor was within the limit. In conclusion, a dynamically allocated limitation logic to helicopter FBW controller was verified by simulation.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.24-34
• /
• 2007

Closed-loop active twist control of integral helicopter rotor blades is investigated in this paper for reducing hub vibration induced in forward flight. A four-bladed fully articulated integral twist-actuated rotor system has been designed and tested successfully in wind tunnel in open-loop actuation. The integral twist deformation of the blades is generated using active fiber composite actuators embedded in the composite blade construction. An analytical framework is developed to examine integrally twisted helicopter blades and their aeroelastic behavior during different flight conditions. This aeroelastic model stems from a three-dimensional electroelastic beam formulation with geometrical-exactness, and is coupled with finite-state dynamic inflow aerodynamics. A system identification methodology that assumes a linear periodic system is adopted to estimate the harmonic transfer function of the rotor system. A vibration minimizing controller is designed based on this result, which implements a classical disturbance rejection algorithm with some modifications. Using the established analytical framework, the closed-loop controller is numerically simulated and the hub vibratory load reduction capability is demonstrated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.9 s.114
• /
• pp.926-936
• /
• 2006

In this study, structural vibration analyses of a smart unmanned aerial vehicle (UAV) have been conducted considering dynamic loads generated by rotating rotor and wakes. The present UAV (TR-S5-03) finite element model is constructed as a full three-dimensional configuration with different fuel conditions and tilting angles for helicopter, transition and airplane flight modes. Practical computational procedure for modal transient response analysis (MTRA) is established using general purpose finite element method (FEM) and computational fluid dynamics (CFD) technique. The dynamic loads generated by rotating blades in the transient and forward flight conditions are calculated by unsteady CFD technique with sliding mesh concept. As the results of present study, transient structural displacements and accelerations are presented in detail. In addition, vibration characteristics of structural parts and installed equipments are investigated for different fuel conditions and tilting angles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.11
• /
• pp.1052-1057
• /
• 2007

A highly reliable Video Transmission System (VTS) was developed in order to obtain both video and digital data simultaneously in the real time flight test situation of a flying vehicle. The VTS integrates GPS data, digital telemetry data and video signals into a compact digital data package which is compressed and processed by an MPEG-2 Encoder and a DVB-S modulator respectively. The DVB-S modulator is composed of a specially devised Forward Error Correction processor and base band QPSK modulator. The designed VTS was verified and proved for its required functioning and performance through separate flight tests using an airplane and missiles.

• Journal of Korean Society for Quality Management
• /
• v.41 no.3
• /
• pp.405-412
• /
• 2013

Purpose: In this paper, the improvement of the image quality is investigated. The image quality is degraded by the drift phenomenon of EO/IR (Electro-Optical/Infrared) device on UAV. The drift phenomenon means that the image of EO/IR equipment on UAV(Unmanned Aerial Vehicle) moves to the unintended direction. This phenomenon should be improved for successful flight mission. Methods: To improve the drift phenomenon, the drift compensation method, the combination algorithm of FMC(Forward Motion Compensation) and AMC(Angular Motion Compensation) method, are introduced to calculate pitch and azimuth angle. Result values of pitch and azimuth angle are used for the improvement of image quality in EO/IR control logic. Results: The image quality is quantitatively improved more than 15 times through field test data of flight. Conclusion: Using the drift compensation technique, the image quality for EO/IR equipment is improved over 15 times than existing methods. This means the user of UAV with EO/IR device can perform a successful mission by keeping the line of sight for the target accurately.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.367-375
• /
• 2006

In this study, structural vibration analyses of a smart unmanned aerial vehicle (UAV) have been conducted considering dynamic loads generated by rotating rotor and wakes. The present UAV (TR-S5-03) finite element model is constructed as a full three-dimensional configuration with different fuel conditions and tilting angles for helicopter, transition and airplane flight modes. Practical computational procedure for modal transient response analysis (MTRA) is established. using general purpose finite element method (FEM) and computational fluid dynamics (CFD) technique. The dynamic loads generated by rotating blades in the transient and forward flight conditions are calculated by unsteady CFD technique with sliding mesh concept. As the results of present study, transient structural displacements and accelerations are presented in detail. In addition, vibration characteristics of structural parts and installed equipments are investigated for different fuel conditions and tilting angles.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.60-65
• /
• 2009

A highly reliable Video Transmission System (VTS) was developed in order to obtain both video and digital data simultaneously in the real time flight test situation of a flying vehicle. The VTS integrates GPS date digital telemetry data and video signals into a compact digital data package which is compressed and processed by an MPEG-2 Encoder and a modulator respectively. The modulator is composed of a specially devised Forward Error Correction processor and base band QPSK modulator. The designed VTS was verified and proved for its required functioning and performance through separate flight tests using an airplane and Rockets.