• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.45-50
• /
• 2017

We investigated effect of Zn content on shear strengh of Sn-0.7Cu-xZn and OSP surface finished solder joints. Five pastes of Sn-0.7Cu-xZn (x=0, 0.5, 1.0, 1.5, 2.0 wt.%) solders were fabricated by mixing of solder powder and flux using planatary mixer. $180{\mu}m$ diameter solder balls were formed on OSP surface finished Cu electrodes by screen print method, and the reflow process was performed. The shear strength was evaluated with two high shear speeds; 0.01 and 0.1 m/s. The thickness of the intermetallic compound(IMC) layer was decreased with increasing Zn content in Sn-0.7Cu-xZn solder. The highest shear strength was 3.47 N at the Zn content of 0.5 wt.%. As a whole, the shear strength at condition of 0.1 m/s was higher than that of 0.01 m/s because of impact stress. Fracture energies were calculated by F-x (Force-displacement) curve during high speed shear test and the tendency of fracture energy and that of shear strength were good agreement each other. Fracture took place within solder matrix at lower Zn content, and fracture occured near the interface of OSP surface finished Cu electrode and solder at higher Zn content.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.22-27
• /
• 2010

To improve surface wettability, each sample was treated by atmospheric pressure plasma (APP) using dielectric barrier discharge (DBD) system. Argon and oxygen gases were used for treatment gas to modify the $TiO_2$ surface by APP with RF power range from 50 to 200 W. Water contact angle was decreased from $20^{\circ}$ to $10^{\circ}$ with argon only. However, water contact angle was decreased from $20^{\circ}$ to < $1^{\circ}$ with mixture of argon and oxygen. Water contact angle with $O_2$ plasma was lower than water contact angle with Ar plasma at the same RF power. It seems to be increasing the polar force of $TiO_2$ surface. Also, analysis result of X-ray photoelectron spectra (XPS) shows the increase of intensity of O1s shoulder peak, resulting in increasing of surface wettability by APP. Moreover, each water contact angle increased according to increase past time. However, contact angle increase with plasma treatment was lower than without plasma treatment. Additionally, the efficiency of $TiO_2$ photocatalyst was improved by plasma surface-treatment through the degradation experiment of phenol.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.323-329
• /
• 2000

In this study we have calculated an ideal complex refractive index of a TiN trim used in a layer of anl1reilecnon (I\R) coatmg, [air$ISiO_2ITiNIglass$] in the visible. Also we simulated the rellectance of lwo-layer AR coating by varying the thicknesses of TiN and $SiO_2$ layers, respecl1vely. The simolation results show that we can controllhe lowest reflectance and AR band of tile AR coating. The TIN fihns were fabricated by a RF magnetron sputtering apparalus. The chemical, structural and electrical properties of TiN fih11S were inveshgated by the Rutherford backscattering spech'oscopy (RBS), atomic force microscope (AFM) and 4-point probe. The optical properlies were inve,tigated by the spectrophotometer and vanable angle spectroscopic ellipsometer (VASE). The smface roughness of TiN flhns \vas $9~10\AA$. TIle resistivity of TiN films was TEX>$360~730\mu$\Omega $ cm. The ,toichlOllletry of TiN film was 1'1: O:N = I: 0.65 :0.95 and ilic oxygen wa~ found on ilie smface. With these experimental and simu]al1on resulLs, we deposited duo: two-layer AR coating, [air$ISiO_2ITiNIglass$] and the refleClance was under 0.5% ill the regIOn of 440-650 run. 0 run.

• Korean Journal of Materials Research
• /
• v.6 no.8
• /
• pp.817-824
• /
• 1996

Removal of Cu impurities on Si substrates using remote H-plasma was investigated. Si substrates were intentionally contaminated by 1ppm ${CuCI}_{2}$, standard chemical solution. To determine the optimal process condition, remote H-plasma cleaning was conducted varying the parameters of rf power, cleaning time and remoteness(the distance between the center of plasma and the surface of Si substrate). After remote H-plasma cleaning was conducted, Si surfaces were analysed by TXRF(total x-ray reflection fluorescence) and AFM(atomic force microscope). The concentration of Cu impurity was reduced by more than a factor of 10 and its RMS roughness was improved by more than 30% after remote H-plasma cleaning. TXRF analysis results show that remote H-plasma cleaning is effective in eliminating Cu impurity on Si surface when it is performed under the optimal process condition. AFM analysis results also verifies that remote H-plasma cleaning makes no damage to the Si surface. The deposition mechanism of Cu impurity may be explained by the redox potential(oxidation-reduction reaction potential) theory. Based on the XPS analysis results we could draw a conclusion that Cu impurities on the Si substrate are removed together with the oxide by a "lift-off" mechanism when the chemical oxide( which forms when Cu ions are adsorbed on the Si surface) is etched off by reactive hydrogen atoms.gen atoms.

• Korean Journal of Materials Research
• /
• v.15 no.4
• /
• pp.275-280
• /
• 2005

The growth of hafnium oxide thin films by atomic layer deposition was investigated in the temperature range of $175-350^{\circ}C$ using $Hf[N(CH_3)_2]_4\;and\;O_2$ as precursors. A self-limiting growth of $0.6\AA/cycle$ was achieved at the substrate temperature of $240-280^{\circ}C$. The films were amorphous and very smooth (0.76-0.80 nm) as examined by X-ray diffractometer and atomic force microscopy, respectively. X-ray photoelectron spectroscopy analysis showed that the films grown at $300^{\circ}C$ was almost stoichiometric. Electrical measurements performed on $MoW/HfO_2$(20 nm)/Si MOS structures exhibited high dielectric constant$(\~17)$ and a remarkably low leakage current density of at an applied field of $1.5-6.2\times10^{-7}A/cm^2$ MV/cm, probably due to the stoichiometry of the films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.391-392
• /
• 2012

Graphene is a perfectly two-dimensional (2D) atomic crystal which consists of sp2 bonded carbon atoms like a honeycomb lattice. With its unique structure, graphene provides outstanding electrical, mechanical, and optical properties, thus enabling wide variety of applications including a strong potential to extend the technology beyond the conventional Si based electronic materials. Currently, the widespread application for electrostatically switchable devices is limited by its characteristic of zero-energy gap and complex process in its synthesis. Several groups have investigated nanoribbon, strained, or nanomeshed graphenes to induce a band gap. Among various techniques to synthesize graphene, chemical vapor deposition (CVD) is suited to make relatively large scale growth of graphene layers. Direct growth of graphene on hexagonal boron nitride (h-BN) using CVD has gained much attention as the atomically smooth surface, relatively small lattice mismatch (~1.7％) of h-BN provides good quality graphene with high mobility. In addition, induced band gap of graphene on h-BN has been demonstrated to a meaningful value about ~0.5 eV.[1] In this paper, we report the synthesis of grpahene / h-BN bilayer in a chemical vapor deposition (CVD) process by controlling the gas flux ratio and deposition rate with temperature. The h-BN (99.99％) substrate, pure Ar as carrier gas, and $CH_4$ are used to grow graphene. The number of graphene layer grown on the h-BN tends to be proportional to growth time and $CH_4$ gas flow rate. Epitaxially grown graphene on h-BN are characterized by scanning electron microscopy, atomic force microscopy, and Raman spectroscopy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.404-404
• /
• 2012

저차원계 탄소 동소체는 특유의 구조에서 기인하는 우수한 물리적 성질로 인해 각광받고 있는 물질이다. 탄소원자가 육각형 격자 모양을 지닌 2차원계 물질인 그래핀(graphene)은 뛰어난 전기적, 물리적, 광학적 성질로 인해 전계효과 트랜지스터(field effect transistors), 투명전극(transparent electrodes), 에너지 저장체, 복합체, 화학/바이오 센서 등 다양한 분야에서 활용을 위한 연구가 진행되고 있다. 또한 그래핀이 튜브형태로 말려있는 1차원계 물질인 탄소나노튜브(carbon nanotube)의 전기적, 열적, 기계적 성질은 이를 전계방출 디스플레이(field emission display), 전도성 플라스틱, 가스 저장체, 슈퍼 커패시터 등에 적용가능하게 한다. 최근 2차원계 물질인 그래핀과 1차원계 물질인 탄소나노튜브의 장점을 극대화하기 위한 복합 나노 구조에 대한 다양한 연구가 진행되고 있는 추세이다[1-5]. 본 연구에서 그래핀-탄소나노튜브 혼성 구조의 제작은 다음과 같이 진행되었다. 우선 열 화학기상증착법(thermal chemical vapor deposition)을 이용하여 그래핀을 합성하였다. 합성된 그래핀은 메타크릴산메탈 수지(polymetylmethacrylate; PMMA)를 이용한 전사(transfer)방법을 이용하여 원하는 기판에 위치시키고, 직류 마그네트론 스퍼터링(DC magnetron sputtering)을 이용하여 탄소나노튜브의 합성을 위한 촉매층을 증착하였다. 이후 열 화학기상증착법을 이용하여 그래핀 위에 탄소나노튜브를 합성함으로써 그래핀-탄소나노튜브 혼성 구조를 제작하였다. 합성된 그래핀-탄소나노튜브의 구조적 특징은 주사 전자 현미경(scanning electron microscopy)을 통해 확인하였고, 촉매의 표면 형상 및 화학적 상태는 원자힘 현미경(atomic force microscopy)과 X선 광전자 분광법(X-ray photoelectron spectroscopy)을 통해 확인하였다. 또한 제작된 그래핀-탄소나노튜브의 전기적 특성 측정을 통해 나노전자소자로의 응용가능성을 조사하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.278-279
• /
• 2012

최근 들어 세계적인 고유가 행진과 화석연료 고갈에 대응하기 위하여 대체 에너지원 발굴에 대한 필요성이 높아지고 있다. 그 중 CIGS 박막 태양전지는 미래 신재생 에너지 자원의 가장 유망한 후보군 중 하나이다. 기존의 Si 기반의 태양전지의 경우 시간경과에 따른 효율 저하, 높은 재료비, 복잡한 공정으로 인하여 대량생산이 힘든 단점을 가지고 있다. 반면 박막 태양전지의 경우 생산 원가를 낮출 수 있는 태양전지 제조기술로서는 2세대 태양전지로 불리우며, 에너지 변환 효율과 생산 원가에서 우월성을 가진다. 그리고 이러한 CIGS 박막 태양전지를 단일 CIGS 타겟을 이용하여 스퍼터링 공정으로 제작하면 기존에 사용되었던 동시 증발법에 비해서 간단하고 대면적 코팅 및 대량 생산이 가능하다. 본 연구에서 사용된 기판으로는 $25{\times}25mm$ 크기의 Soda Lime Glass (SLG) 위에 DC 마그네트론 스퍼터링 공정으로 Mo가 $1{\mu}m$ 증착된 시편을 이용하여, 2 inch 단일 CIGS 타겟 (MATERION, CIGS Target 25-17.5-7.5-50 at%)을 기판 가열하여 증착하였다. RF 파워는 80 W, 기판 온도는 RT, 100, 200, 300, $400^{\circ}C$로 가열 후 증착하였고, CIGS 박막의 두께는 약 $1{\mu}m$로 일정하게 하였다. CIGS/Mo 박막의 파워별 미세구조 분석을 위해 X-ray Diffraction (XRD, BRUKER GADDS)로 측정하였으며, 박막의 결정립 크기를 확인하기 위해 Field Emission Scanning Electron Microscopy (FE-SEM, HITACHI)을 사용하여 측정하였다. 조건별 박막의 조성 분석 및 표면조도는 Energy Dispersive X-ray Spectroscopy (EDS, HORIBA 7395-H)와 Atomic Force Microscopy (AFM)을 이용하여 각각 평가하였다. 마지막으로 광학적 특성을 평가하고 박막의 밴드갭 에너지를 계산하기 위해서 190 nm에서 1,100 nm의 영역 대에서 자외선 광학 측정기(UV-Vis, HP-8453, AGLIENT)로 투과도를 측정하여 밴드갭 에너지를 계산하였다. 증착된 CIGS 박막은 기판 온도가 증가함에 따라 결정립 크기가 커지는 경향을 보였다. 이는 기판 상에 도달한 스퍼터 원자의 확산 에너지 증가로 인한 것으로 생각되어진다. 또한, 기판온도에 따른 결정립 성장 변화는 4성분계의 박막의 조성 및 핵생성 밀도와 관련되어 설명되어질 것이다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.112-112
• /
• 2009

In this study, the effect of a long post-deposition thermal annealing(600 and 1000 $^{\circ}C$) on the surface acoustic wave (SAW) properties of polycrystalline (poly) aluminum-nitride (AlN) thin films grown on a 3C-SiC buffer layer was investigates. The poly-AlN thin films with a (0002) preferred orientation were deposited on the substrates by using a pulsed reactive magnetron sputtering system. Experimental results show that the texture degree of AlN thin film was reduced along the increase in annealing temperature, which caused the decrease in the electromechanical coupling coefficient ($k^2$). The SAW velocity also was decreased slightly by the increase in root mean square (RMS) roughness over annealing temperature. However, the residual stress in films almost was not affect by thermal annealing process due to small lattice mismatch different and similar coefficient temperature expansion (CTE) between AlN and 3C-SiC. After the AlN film annealed at 1000 $^{\circ}C$, the insertion loss of an $IDT/AlN/3C-SiC/SiO_2/Si$ structure (-16.44 dB) was reduced by 8.79 dB in comparison with that of the as-deposited film (-25.23 dB). The improvement in the insertion loss of the film was fined according to the decrease in the grain size. The characteristics of AlN thin films were also evaluated using Fourier transform-infrared spectroscopy (FT-IR) spectra and X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) images.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.209-209
• /
• 2009

ITO 박막은 박막 태양전지, 유기 태양전지뿐만 아니라 유연한 디스플레이, 발광다이오드와 같은 광학적 장치에 투명한 전극으로써 널리 사용된다. 글라스나 플라스틱 기판위에 형성된 투명 전극은 식각을 통하여 전기회로를 구성한다. 또한 식각 특성을 개선할 필요가 있다. 이 연구에서 우리는 유리 기판위에 코팅된 ITO 박막을 유도결합 $BCl_3/Ar$ 플라즈마를 이용하여 식각하였다. ITO 박막은 RF 마그네트론 스퍼터링을 사용해 200 $^{\circ}C$에서 비알칼리 글라스 위에 증착하였고 ITO 박막의 총 두께는 약 250 nm 이었다. 또한 전기 전도성은 $4.483{\times}10^{-4}{\Omega}cm$, 캐리어 농도는 $3.923{\times}10^{20}cm^{-3}$이고, 홀 이동도는 $3.545{\times}10cm^{-2}/Vs$이었다. Ar 플라즈마에 $BCl_3$ 가스를 첨가시키면서 가스 비율에 따른 ITO의 식각 속도와 ITO와 PR과의 선택비를 측정하였다. 최대 식각 속도는 $BCl_3$(25%)/Ar(75%), 500 W의 RF power, -200 V의 DC-bias voltage, 그리고 2 pa의 공정압력일 때 588 nm/min이었고 선택비는 0.43으로 다소 낮게 측정되었다. 식각된 표면의 화학적 반응은 엑스선 광전자 분광법 (X-ray Photoelectron Spectroscopy)을 사용해 조사되었다. 그리고 식각된 표면의 거칠기는 원자현미경 (Atomic Force Microscopy)을 사용해 측정하였다.