• 문화기술의 융합
• /
• 제9권4호
• /
• pp.549-555
• /
• 2023

공용중인 고속철도의 PSC Box 교량의 긴장력 관리는 교량 성능에 있어 매우 중요한 기능으로 교량 유지관리시 세밀한 관리가 필요하다. 이에 본 연구에서는 열차(활하중) 재하시험 없이 측정한 상시처짐 결과를 이용하여 PSC Box girder 내부의 긴장력 감소 수준과 긴장력 손실에 다른 재긴장 예측 시기를 연구하고자 한다. PSC Box 거더의 긴장력 감소에 따른 재긴장 시기 예측결과, 준공 이후 약 17년 이전에서는 긴장력 감소(Jacking force loss) 곡선이 완만한 것으로 나나낫다. 그러나 17년 이후에서는 긴장력 감소 곡선이 급격하게 변화되는 것으로 나타났다. 따라서 공용연수 증가에 따라 긴장력이 감소하는 것으로 확인되었고, 구조물의 노후화가 진행될수록 긴장재의 손신을 더 급격하게 증가되는 것으로 분석되었다. 향후 공용중인 PSC Box 교량중에서 준공 이후 18년 이상 경과된 구조물의 경우 긴장재 및 주변 손상에 대한 정밀조사가 필요할 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.273-280
• /
• 2003

Tunneling in difficult geological conditions is often inevitable especially in urban areas. Ground improvement and reinforcement techniques are often required to guarantee safe tunnel excavations and/or to prevent damage to adjacent structures. The steel pipe-reinforced multi-step grouting method has been recently applied to tunnel sites in Korea as an auxiliary technique. In this study, the face stability with steel pipe-reinforced multi-step grouting was evaluated by simultaneously considering two factors: one is the effective stress acting on the tunnel face calculated by limit theorem and limit equilibrium method; the other is the seepage force obtained by means of numerical analysis. The study revealed that the influence of the steel pipe-reinforced multi-step grouting on the support pressure in dry condition is not significant while there is relatively a large amount of reduction in seepage forces by adopting the technique in saturated condition. The effect of the anisotropy of permeability on the seepage force acting on the tunnel face was also estimated by conducting the coupled analysis. It was found that a higher horizontal permeability compared with the vertical one causes reduction in the seepage force acting on the tunnel face.

• 한국정밀공학회지
• /
• 제20권9호
• /
• pp.126-134
• /
• 2003

This paper investigates the multi-pass wet wire drawing process considering the slip between the wire and the capstan. The production of fine wire through multi-pass wet wire drawing process would be impossible without backtension. The backtension is affected by many process parameters, such as slip, dies reduction, coiling number of wire at the capstan, machine reduction, characteristic of lubricant etc. Up to date, die design and dies pass schedule of multi-pass wet wire drawing process have been performed by trial and error of expert in the industrial field. In this study, an analysis program which can perform the analysis and considering the effect of slip at each capstan was developed. The effects of many important parameters (drawing force, backtension force, needed power, slip rate, slip velocity rate etc.) on multi-pass wet wire drawing process can be predicted by this developed program. It is possible to obtain the important basic data which can be used in the pass schedule of multi-pass wet wire drawing process by using this developed program.

• 수산해양기술연구
• /
• 제50권2호
• /
• pp.176-184
• /
• 2014

Nowadays, consumption of fisheries products is increasing. There are several factors, one of which is a quantitative development through aquaculture. Another factor is an increase qualitative consumption of fish which require that fish be supplied alive. This requires a lot of technical effort to transport the live fish that have low survival rate (c.f. tuna and mackerel) in coastal waters and in the open sea. To develop a towing cage for transporting the live fish, model test in a circulate water channel and simulation by computer tool were carried out. In order to spread vertically, floats were attached at the upper part of the cage, and iron chains attached at the lower part of the cage. For horizontal spreading, kites were attached on the cage. The tension and spreading performance of the cage were measured. The result shows that the tension and reduction ratio of inside volume of the cage were tended to increase with increased towing speeds. The suitable operation condition in towing cage was 1.0 m/s towing speeds with vertical spreading force 8.7 kN, horizontal spreading force 5.6 kN; in this case the reduction ratio of inside volume of the cage was estimated as 25%.

• Computers and Concrete
• /
• 제22권6호
• /
• pp.515-525
• /
• 2018

This paper presents a numerical study on the performance of reinforced concrete (RC) bridge structures subjected to heavy goods vehicle (HGV) collision. The objectives of this study are to investigate the dynamic response and failure modes of different types of bridges under impact loading as well as to give an insight into the simplified methods for modeling bridge structures. For this purpose, detailed finite-element models of HGV and bridges are established and verified against the full-scale collision experiment and a recent traffic accident. An intensive parametric study with the consideration of vehicle weight, vehicle velocity, structural type, simplified methods for modeling bridges is conducted; then the failure mode, impact force, deformation and internal force distribution of the validated bridge models are discussed. It is observed that the structural type has a significant effect on the force-transferring mechanism, failure mode and dynamic response of bridge structures, thus it should be considered in the anti-impact design of bridge structures. The impact force of HGV is mainly determined by the impact weight, impact velocity and contact interface, rather than the simplification of the superstructure. Furthermore, to reduce the modeling and computing cost, it is suggested to utilize the simplified bridge model considering the inertial effect of the superstructure to evaluate the structural impact behavior within a reasonable precision range.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.47-54
• /
• 2023

The research direction of the automobile industry worldwide is speeding up research to improve fuel efficiency through weight reduction as the weight of automobiles increases due to environmental problems, convenience demands, and safety problems. As a way to solve weight reduction, there is a method of improving mechanical properties by improving the development and manufacturing method of lightweight materials with replaceable mechanical properties. Therefore, research on the molding and processing technology of aluminum, which is a lightweight material, is being actively conducted. In this study, aluminum material was applied. By using Autoform S/W, a press forming analysis program, the blank holding force, mold die R, and bead restraint force were selected in three levels, respectively, and the results and optimization of formability and shape freezing were carried out. In this study, aluminum material was applied. By using Autoform S/W, a press molding analysis program, the blank holding force, mold die R, and bead restraint force were selected in three levels, respectively, and the results and optimization of formability and shape freezing were carried out. The optimized results were confirmed by comparative analysis of formability and Spring Back. As a result of the experiment, it was possible to confirm the result value of the Spring Back of the final product according to the tensile change of the material.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.249-254
• /
• 2002

Adhesive contact characteristics of torus-shaped bumps were analyzed using the finite element technique considering the adhesive force. Analyses focused on the effect of rim and bump radii on the adhesive contact behavior such as the jump-to-contact behavior, adhesion hysteresis, pull-off forces, contact region and pressure, and surface and subsurface stresses. Analysis results in the absence of adhesive force were also included to examine the effect of adhesive force. The applicability of torus-shaped bumps to the MEMS structure for reduction of friction is discussed.

• 대한수학회논문집
• /
• 제15권1호
• /
• pp.133-142
• /
• 2000

We consider some numerical solution methods for equilibrium equations Af + E$^{T}$ λ = r, Ef = s. Algebraic problems of this form evolve from many applications such as structural optimization, fluid flow, and circuits. An important approach, called the force method, to the solution to such problems involves dimension reduction nullspace computation for E. The purpose of this paper is to investigate the substructuring method for the solution step of the force method in the context of the incompressible fluid flow. We also suggests some iterative methods based upon substructuring scheme..

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.643-645
• /
• 2008

To obtain weight reduction and high performance, level set based topology optimization in magnetic fields is promising for the design of magnetic devices where the precise boundary shape and topological chanages are required. Level set function is introduced to represent ferromagnetic material boundaries and material properties of the magnetic reluctivity are determined. The optimization problem is formulated for maximizing the actuating force in a prescribed direction under limited usage of ferromagnetic material.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.454-458
• /
• 2001

In this paper, contact between the coupler-roller and guide in elevator door mechanism is modeled and analyzed with DADS 3D program. The contact force of coupler-roller is an important factor for impact and noise reduction when doors of elevator are opened or closed. To minimize the maximum contact force, an optimal cam profile for the door guide is suggested. To find an optimal shape of the guide, several types of motion curve are tested with DADS contact module.