• Journal of Bio-Environment Control
• /
• v.22 no.2
• /
• pp.138-145
• /
• 2013

In order to develop the efficient control algorithm of the two-fluid fogging system, cooling experiments for the many different types of fogging cycles were conducted in tomato greenhouses. It showed that the cooling effect was 1.2 to $4.0^{\circ}C$ and the cooling efficiency was 8.2 to 32.9% on average. The cooling efficiency with fogging interval was highest in the case of the fogging cycle of 90 seconds. The cooling efficiency showed a tendency to increase as the fogging time increased and the stopping time decreased. As the spray rate of fog in the two-fluid fogging system increased, there was a tendency for the cooling efficiency to improve. However, as the inside air approaches its saturation level, even though the spray rate of fog increases, it does not lead to further evaporation. Thus, it can be inferred that increasing the spray rate of fog before the inside air reaches the saturation level could make higher the cooling efficiency. As cooling efficiency increases, the saturation deficit of inside air decreased and the difference between absolute humidity of inside and outside air increased. The more fog evaporated, the difference between absolute humidity of inside and outside air tended to increase and as the result, the discharge of vapor due to ventilation occurs more easily, which again lead to an increase in the evaporation rate and ultimately increase in the cooling efficiency. Regression analysis result on the saturation deficit of inside air showed that the fogging time needed to change of saturation deficit of $10g{\cdot}kg^{-1}$ was 120 seconds and stopping time was 60 seconds. But in order to decrease the amplitude of temperature and to increase the cooling efficiency, the fluctuation range of saturation deficit was set to $5g{\cdot}kg^{-1}$ and we decided that the fogging-stopping time of 60-30 seconds was more appropriate. Control types of two-fluid fogging systems were classified as computer control or simple control, and their control algorithms were derived. We recommend that if the two-fluid fogging system is controlled by manipulating only the set point of temperature, humidity, and on-off time, it would be best to set up the on-off time at 60-30 seconds in time control, the lower limit of air temperature at 30 to $32^{\circ}C$ and the upper limit of relative humidity at 85 to 90%.

• Journal of the Korean Society of Industry Convergence
• /
• v.13 no.1
• /
• pp.31-39
• /
• 2010

An exergy analysis is carried out for the regenerative gas turbine cycle which has a potential of enhanced thermal efficiency and specific power owing to the more possible water injection than that of inlet fogging under the ambient conditions. Using the analysis model in the view of the second law of thermodynamics, the effects of pressure ratio, water injection ratio and ambient temperature are investigated on the performance of the system such as exergetic efficiency, heat recovery ratio of recuperator, exergy destruction or loss ratios, and on the optimal conditions for maximum exergy efficiency. The results of computation for the typical cases show that the regenerative gas turbine system with afterfogging can make a notable enhancement of exergy efficiency.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.8
• /
• pp.448-455
• /
• 2009

A performance analysis of the regenerative gas turbine system with afterfogging is carried out. Because of the high temperature at the outlet of air compressor, afterfogging has a potential of improved recuperation of exhaust heat than inlet fogging. Thermodynamic analysis model of the gas turbine system is developed by using an ideal gas assumption. Using the model, the effects of pressure ratio, water injection ratio, and ambient temperature are investigated parametrically on thermal efficiency and specific power of the cycle. The dependency of pressure ratio giving peak thermal efficiency is also investigated. The results of numerical computation for the typical cases show that the regenerative gas turbine system with afterfogging can make a notable enhancement of thermal efficiency and specific power. In addition, the peak thermal efficiency is shown to decrease almost linearly with ambient temperature.

• Journal of Ginseng Research
• /
• v.34 no.1
• /
• pp.23-29
• /
• 2010

This study examined the biological characteristics of the insect and examined potential cultural controls using peduncle topping methods. Ginseng stem fungus gnat eggs hatched after 5 days; ecdysis lasted 3-4 weeks, and after 5 days pupation, adults emerged. Adults deposited eggs 1-2 days after emerging, and the entire life cycle lasted 32-40 days. The fungus gnats laid eggs $327\times220{\mu}m$ in size on cut planes of stems, but not on intact stem parts that had not been topped or wounded. Analyses of major weather data for the experimental areas and weather data for the past 30 years acquired from the Korea Meteorological Administration revealed that fungus gnat dispersion was prevalent under highly humid conditions and in areas with thick and frequent fogging. Among the topping times examined, fungus gnat damage to ginseng was lowest when topping occurred in late May. Among the five different topping methods evaluated on experimental ginseng farms, the cumulative fungus gnat damage to ginseng was low (0.8%) under partial peduncle topping (removal of peduncle with lateral fruit remaining) and removal of only flower buds (0.6%), with fungus gnat control effects of 82% and 86%, respectively, compared to conventional topping (removal of peduncle about 5 cm above its base). No fungus gnat damage to ginseng was observed under the no-topping treatment. These results suggest that partial topping of peduncles, while letting lateral fruits remain, is a potentially environmentally friendly method of controlling the ginseng stem fungus gnat.