• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.283-288
• /
• 2003

Alkaline powder cleaning agents (APCAs) were prepared by blending of $Na_2CO_3$ tetrasodium pyrophosphate (TSPP). sodium orthosilicate (Na-OSi), Na-dioctyl sulfosuccinate (303C), Demol C, and MJU-100A (100A). The physical properties of APCAs tested with steel specimen showed the following results. The cleaning powers of APCA-6 ($Na_2CO_3$ 250g/TSPP 70g/Na-OSi 40g/303C 60g/Demol C 50g/100A 30g mixture) for press-rust preventing oil was 97% and 98% degreasing at 2wt%, $70^{\circ}C$ and $90^{\circ}C$, respectively; for Quenching oil, the cleaning power of APCA-6 was 95% degreasing at 2wt% and $70^{\circ}C$. From the results, it was ascertained that APCA-6 exhibited a good cleaning power. Also low foaming power tests proved that the APCA-6 maintained good defoaming effect.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.3
• /
• pp.25-31
• /
• 2000

It is required to use substantial amount of wet strength resin for producing multi-functional mulch papers since these paper products shold maintain its strength properties when they exposed to outdoor weather for several months. While producing mulch papers it is usual to observe significant amount of foam at white water silo. Thus it is imperative to use defoaming or antifoaming agents. In this study diverse defoaming and antifoaming agents have been tested for their effective-ness in eliminating foams that produced. It was shown that combined use of a silicone type defoamer and a fatty acid type anti-foaming agent was msot effective in eliminating foams. These chemicals were used in trial production of mulch papers and their influence on paper-making wet end system was examined including one pass retention cationic demand con-ductivity pH etc. It was found that the defoaming agents were very effective for removing foams in trial production. Tensile strengths of the mulch papers produced were significantly greater than commericial mulch papers produced in Japan.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.519-526
• /
• 2005

Hydrolysis of soda-lime waste glass was investigated to test the feasibility for use of waste glass as feed material in the production of foamed glass. The soda-lime glass, such as plate glass and various bottle glasses, was effectively hydrolyzed by steam and water under high pressure. The proper condition for the hydrolysis was found to be reaction temperature of $250^{\circ}C$ and reaction time of 2 h. Under this condition, the water content of hydrated glass through hydrolysis was 7.85~10.04%, allowing successful foaming process for production of foamed glass. Using Na as the modifying agent of glass was effective in the hydrolysis by water. The highest water content of hydrated glass was obtained when weight ratio of NaOH to the glass was 0.04.

• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.528-535
• /
• 2001

Polyurethane specimens were mainly composed of polyol, MDI, silicone surfactant, and water. The effects of ethylene glycol on the cell size, forming magnification, cream time, gel time, take free time, final free rising height, and reactive temperature were investigated. The cyclopentane was used for PU foam as a physical blowing agent. The components were hand-mixed at about 5000 rpm within 4 seconds at room temperature. The mixtures with various ethylene glycol contents were foamed in the wood mold. When the index of isocyanate was fixed, as the amount of ethylene glycol increased, cell size and thermal conductivity were decreased by about 5.1% and 14%, respectively.

• Journal of the Society of Disaster Information
• /
• v.8 no.3
• /
• pp.204-212
• /
• 2012

Lightweight soils are very economical and environment friendly materials that are valuable in field without wasting construction materials, dredged soils and clay/ silty soils during construction. Recently, the research of lightweight soils mixed with recycled material (recycled tire powder, rice husks) have been investigated. In this study the mix design factors (i.e., weight of soil, water content, foaming agent and added water) were analyzed and optimized mix design was suggested using cement content for revealing strength. For the analysis the stress-strain behavior, strength with respect to time, and experimental strength for the component of recycled material were analyzed. Finally, target strength was determined to calculate reasonable and economical mix ratio and the optimized cement content was suggested.

• Journal of the Korean Applied Science and Technology
• /
• v.6 no.1
• /
• pp.51-57
• /
• 1989

A series of four sodium ${\alpha}-sulfo$ fatty vinyl ester oligomers including sodium ${\alpha}-sulfo$ lauric acid vinyl ester oligomer, sodium ${\alpha}-sulfo$ myristic acid vinyl ester oligomer, sodium ${\alpha}-sulfo$ palmitic acid vinyl ester oligomer and sodium ${\alpha}-sulfo$ stearic acid vinyl ester oligomer were examined for surface activities such as surface tension, foaming power, foam stability, emulsifying power, dispersion effect, solubilization of orange OT. The critical micelle concentration(CMC) was also evaluated. Consequently, these sodium ${\alpha}-sulfo$ fatty acid vinyl ester oligomers were shown to have a good cohesive power and dispersion effect.

• Journal of the Korean Applied Science and Technology
• /
• v.10 no.2
• /
• pp.81-90
• /
• 1993

The Surfactants composed of acylated aterocollagen which is produced by the acylation of the side chain amino radicals of aterocollagen with an aliphatic acid having 12 to 18 carbon atoms will be discussed in this study. This condensation is done at moderate reaction temperature (<$25^{\circ}C$) in aqueous alkaline solution. The products of this reaction were identified by UV/VIS spectroscopy and infrared spectroscopy. For these compounds, surface active properties and physical properties including isoelectric point, Krafft point, surface tension, critical micelle concentration(cmc), foaming power, viscosity behaviour, water holding capacity, skin irritation and emulsifying power were measured respectively. The experimental results received that the products have a good emulsifying power, excellent water holding capacity while having low skin irritation. Thus, these derivatives will be expected to be used as an emulsifying agent for O/W type cosmetic emulsion.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.2
• /
• pp.232-239
• /
• 2011

Fabric fibrous filter has been used in various industrial applications owing to the low cost and wide generality. However, the basic properties of fabric materials often limit the practical utilization including hot gas cleaning. This study attempts to find new coatings of porous fibrous filter media in order to overcome its insufficient thermal resistance and durability. Teflon was one of the plausible chemicals to supplement the vulnerability against frequent external thermal impacts. A foaming agent composed of Teflon and some organic additives was tentatively coated on the glass fiber mat. The present test Teflon foam coated filter was fount to be useful for hot gas cleaning, up to $250^{\circ}C$-$300^{\circ}C$. Close examination using XPS(X-ray Photoelectron Spectroscopy) and Contact angle proved the binding interactions between carbon and fluorine, which implies coating stability. The PTFE/Glass foam coated filter consisted of more than 95% (C-F)n bond, and showed super-hydrophobic with good-oleophobic characteristics. The contact angle of liquid droplets on the filter surface enabled to find the filter wet-ability against liquid water or oil.

• Journal of the Korean Ceramic Society
• /
• v.55 no.1
• /
• pp.61-66
• /
• 2018

In this study, fabrication method of inorganic insulation were studied to reduce $CO_2$ from buildings. Main materials for inorganic insulation were used cement, blast furnace slag and aluminum powder as foaming agent. Mixing ratio of cement and slag was controlled and physical properties of inorganic insulation were analyzed. When inorganic insulation was fabricated using cement and slag, expanded slurries were not sunken and hardened normally. Pore size was 0.5 - 2 mm; mean pore size was about 1mm in inorganic insulation. Compressive strength of inorganic insulation increased with curing time and increased slightly with cement fineness. However, specific gravity decreased slightly with curing time; this phenomenon was caused by evaporation of adsorptive water. When inorganic insulation was dried at $60^{\circ}C$, compressive strength was higher than that of undried insulation. The highest compressive strength was found with a mixture of cement (50%) and slag (30%) in inorganic insulation. Compressive strength was 0.32 MPa, thermal conductivity was 0.043 W/mK and specific gravity was $0.12g/cm^3$.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.382-390
• /
• 2015

Poly(methyl methacrylate) (PMMA) supports and amine additives were investigated to adsorb $CO_2$. PMMA supports were fabricated by using different ratio of pore forming agents (porogen) to control the BET specific surface area, pore volume and distribution. Toluene and xylene are used for porogens. Supported amine sorbents were prepared by wet impregnation of tetraethylenepentamine (TEPA) on PMMA supports. So we could identify the effect of the pore structure of supports and the quantity of impregnated TEPA on the adsorption capacity. The increased amount of toluene as pore foaming agent resulted in the decreased average pore diameter and the increased BET surface area. Polymer supports with huge different pore distribution could be fabricated by controlling the ratio of porogen. After impregnation, the support with micropore structure is supposed the pore blocking and filling effect so that it has low $CO_2$ capacity and kinetics due to the difficulty of diffusing. Macropore structure indicates fast adsorption capacity and low influence of amine loading. In case of support with mesopore, it has high performance of adsorption capacity and kinetics. So high surface area and meso-/macro- pore structure is suitable for $CO_2$ capture.