• 공업화학
• /
• 제22권6호
• /
• pp.703-710
• /
• 2011

분리막 모듈 내 스페이서는 용액의 원활한 흐름을 위한 공간 확보와 더불어 유체의 난류를 형성시키므로 농도분극화 현상을 감소시키고 막 표면에 축적되는 오염물을 용액 내로 혼합하여 높은 투과유속과 분리막 모듈을 장기간 운전하는데 도움을 준다. 본 연구에서는 분리막 모듈 내 원형, 십자형, 다이아몬드형 및 육각형 단면의 스페이서와 스페이서의 배열 각도, 용질 배제율 및 투과유속에 대한 농도 변화를 "COMSOL Multiphysics" 프로그램으로 수치 해석하여 최적화하였다. 4가지 형태의 스페이서 중에서 십자형 단면 스페이서를 포함한 모듈의 경우가 분리막 표면 농도를 가장 낮게 유지하였으며 스페이서의 배열 각도는 $30^{\circ}$가 효율적이었다. 스페이서가 없는 모듈 출구에서 분리막 표면의 농도는 입구보다 약 2.09배까지 증가하였으나 가장 효율적인 십자형 스페이서를 $30^{\circ}$로 배열할 경우 약 1.29배로서 최대 37% 낮았다. 또한 투과유속이 증가할수록 십자형 스페이서의 농도분극 감소효과는 급격히 증가하였다.

• Membrane and Water Treatment
• /
• 제13권4호
• /
• pp.191-199
• /
• 2022

In industrial production, the development of traditional polyamide nanofiltration (NF) membrane was limited due to its poor oxidation resistance, complex preparation process and high cost. In this study, a composite NF membrane with high flux, high separation performance, high oxidation resistance and simple process preparation was prepared by the method of dilute solution dip coating. And the sulfonated polysulfone was used for dip coating. The results indicated that the concentration of glycerin, the pore size of the based membrane, the composition of the coating solution, and the post-treatment process had important effects on the structure and performance of the composite NF membrane. The composite NF membrane prepared without glycerol protecting based membrane had a low flux, when the concentration of glycerin increased from 5% to 15%, the pure water flux of the composite NF membrane increased from 46.4 LMH to 108.2 LMH, and the salt rejection rate did not change much. By optimizing the coating system, the rejection rate of Na₂SO₄ and PEG1000 was higher than 90%, the pure water flux was higher than 40 LMH (60psi), and it can withstand 20,000 ppm.h NaClO solution cleaning. When the post treatment processes was adjusted, the salt rejection rate of NaCl solution (250 ppm) reached 45.5%, and the flux reached 62.2 LMH.

• 한국환경보건학회지
• /
• 제15권2호
• /
• pp.59-68
• /
• 1989

This study was performed employing the two stage aerated submerged biofilter of media pore size 1.5cm and 2cm, and infiuent substrate concentrations were 30.25mg COD/l, 50.1mg COD/l respectively. The purpose was to determine the treatment efficiency at the low concentration infiuent, reaction order and substrate flux with application of variable-order model that was presented by Rittmann and McCarty. . The results are as follows. 1. Treatment efficiency of 1st reactor was about BOD 82% and COD 76%, when effluent concentration was BOD 3.9 ~ 6.8, COD 7.1 ~ 12.5 mg/l, and this effluent concentration didn't satisfy the water quality grade I, II of river and lake. But as treated effluent of 1st reactor with 2nd reactor, we could achieve appropriate water quality, since instillation of 2nd reactor was needed. 2. Difference of media pore size between 1.5cm and 2cm didn't effect significantly to treatment efficiency and since this of 2nd reactor was about BOD 60%, COD 50%, an consideration of economic point of view should be carried out in field application. 3. Reaction order and substrate flux was varied 0.9851~0.9956 and 0.0028~0.0405 mg/$cm^{2} \cdot day$, and the substrate flux was increased as infiuent substrate concentration increased.

• 한국입자에어로졸학회지
• /
• 제14권2호
• /
• pp.35-40
• /
• 2018

Vertical particle size distribution, total particle concentration, wind velocity, temperature and humidity measurement was performed with a drone. The drone was equipped with a wind sensor, house-made optical particle count(Hy-OPC), condensation particle counter(Hy-CPC), GPS, Temperature, Relative Humidity, Pressure and communication system. Base on the wind velocity and the particle size vertical distribution measurement with drone, the particle mass flux was calculated. The vertical particle distribution showed that the particle number concentration was very strongly correlated with the relative humidity.

• KSBB Journal
• /
• 제6권2호
• /
• pp.207-213
• /
• 1991

In this study poly (1-methyl-4-vinylpyridinium iodide-co-styrene) membrane with pyridinium cation as a fixed carrier was synthesized and the transport characteristics of the membrane was examined over various factors. As the concentration of the fixed carrier in the membrane was increased, the water content was increased. Meanwhile, the counter current of the organic anion and the chloride ion, the following results were obtained. Initial flux of Cl-, organic anion and Na+ decreased with the increasing thickness of membrane, and as the concentration of the fixed carrier increases, the initial flux of Cl- and organic anion increase but the initial flux of Na+ decreased. The flux equation of the organic anion, CCl3COO- was obtained from saturation kinetics as follows;$V_{o}=\frac{(8.67{\times}10^{-5}){\cdot}[NaCl]}{9.63{\times}10^{-2}+[NaCl]} mol/cm^2h$

• 상하수도학회지
• /
• 제16권6호
• /
• pp.717-725
• /
• 2002

A bench-scale submerged-type membrane filtration system (SMFS) was constructed to study a feasibility of membrane filtration for solid-liquid separation in water and wastewater treatment processes. In the case of applying the SMFS to a biological wastewater treatment process, so-called membrane bioreactor, aeration underneath membrane modules is usually employed in order to provide oxygen demand for microbial growth as well as to control membrane fouling. A study was investigated the effects of operation parameters by aeration intensity, feed concentration, foulant type and airlift pore size on critical flux. Critical flux tends to increase with aeration rate. Optimal aeration flow rate was found to be 10 L/min/module. Feed concentration and foulant type has a significant effect on membrane fouling and filtration performance. But downward position and pore size of airlift has no a significant effects on membrane fouling and filtration performance.

• 멤브레인
• /
• 제26권3호
• /
• pp.197-204
• /
• 2016

에스테르(ester)의 모델 수용액으로부터 에스테르 성분을 회수하기 위한 투과증발 공정에서, 공급액의 농도와 온도 변화에 따른 에스테르와 물의 플럭스를 측정하였다. 공급액의 에스테르 농도가 0.15 wt%에서 0.60 wt%로 증가함에 따라 에틸 아세테이트(EA), 프로필 아세테이트(PA), 에틸 프로피오네이트(EP), 부틸 아세테이트(BA), 그리고 에틸 부티레이트(EB)의 플럭스는 증가하였으며, 공급액의 온도가 $30^{\circ}C$에서 $50^{\circ}C$로 증가함에 따라 플럭스가 증가하였다. 에스테르 플럭스의 크기는 (EA) < (PA, EP) < (BA, EB) 순서이었으며, 이는 에스테르와 막 표면과의 친화도에 크게 의존하는 것을 보여준다. 즉, EA는 분자쇄 내에 소수성 기($-CH_2-$)를 1개, (PA, EP)는 2개를 포함하고 있으나, (BA, EB)는 3개를 가지고 있어 가장 소수성이 크기 때문이다. 이러한 에스테르 분자의 소수성이 에스테르 플럭스에 미치는 영향뿐 아니라 막 표면의 소수성이 에스테르 플럭스에 미치는 영향에 관한 연구가 더 필요할 것이다. 온도가 증가함에 따라, EA, PA, EP, BA, and EB 수용액의 물 플럭스는 증가하였으나, 농도 변화에 따른 물 플럭스는 거의 변화가 없었다. 본 투과증발에 대한 실험결과는 기존의 열을 이용하는 증발공정과 증류공정을 대체할 수 있는 공정으로서 향 성분의 회수공정을 개선하는 기초 자료로 활용할 수 있을 것이다.

• 한국대기환경학회지
• /
• 제17권1호
• /
• pp.19-29
• /
• 2001

Atmospheric concentrations of acidic pollutant were measured by the 4 stage filter pak method at Chunchon and by the 3 stage filter pack method at Seoul and Anmyon-do from January to December 1998. The sample was collected for 24 hours on every Wednesday. Concentrations of particulate matters were highest at Anmyon-do. The particulate concentration was much higher during the warm season than other seasons. While the particulate concentration was higher during the warm season, the concentration of gaseous matter was higher in winter. Dry deposition flux was calculated by using reported deposition velocities and concentration of pollutants measured in this study. The dry deposition velocities used in this study for SO$_2$, SO$_{4}^{2}$, HNO$_3$,NO$_{3}^{-}$ and NH$_3$ were 0.29, 0.15, 2.08( 2.13 only for Anmyon-do), 0.20 and 1.00cm/sec, respectively. At Chunchon, annual sulfur flux originated from dry deposition was 384 kg/$textrm{km}^2$, and the flux from wet deposition was 782kg/$textrm{km}^2$. Dry deposition of sulfur was 33% of total sulfur deposition. The annual nitrogen flux originated from dry deposition was 1,892kg/$textrm{km}^2$. And the flux from wet deposition was 1,066kg/$textrm{km}^2$. Dry deposition of nitrogen was 64% of total nitrogen deposition. Dry deposition as well as wet deposition have to be considerd in the study on acidification of environment such as soil or watershed.

• 열처리공학회지
• /
• 제36권6호
• /
• pp.402-411
• /
• 2023

In order to examine the effect of cementite precipitated on the steel surface on the carburizing rate, the carburizing process was carried out at various boost times to measure the mass gain and carbon flux, phase analysis and carbon concentration analysis were performed on the surface of the carburized specimen. In the case of the only boost type, the longer the boost time, the more the mass gain by the diffused carbon follows the parabolic law and tends to increase. In particular, as the boost time increased, the depth of cementite precipitation and the average size of cementite on the steel surface increased. At a boost time of 7 min, the fraction of cementite precipitated on the surface is 7.32 vol.%, and the carburizing rate of carbon into the surface (surface-carbon flux) is about 17.4% compared to the calculated value because the area of the chemical (catalyst) where the carburization reaction takes place is reduced. The measured carbon concentration profile of the carburized specimen tended to be generally lower than the carbon concentration calculated by the model without considering precipitated cementite. On the other hand, in the pulse type, the mass gain by the diffused carbon increased according to the boost time following a linear law. At a boost time of 7 min, the fraction of cementite precipitated on the surface was 3.62 vol.%, and the surface-carbon flux decreased by about 4.1% compared to the calculated value. As a result, a model for predicting the actual carbon flux was presented by applying the carburization resistace coefficient derived from the surface cementite fraction as a variable.

• 대한기계학회논문집B
• /
• 제24권11호
• /
• pp.1428-1436
• /
• 2000

The absorption of vapor involves simultaneous heat and mass transfer in the vapor/liquid system. In this paper, a numerical study for vapor absorption process into LIBr-H$_2$O solution film flowing over helical absorber has been carried out. Axisymmetric cylindrical coordinate system was adopted to model the helical tube and the transport equations were solved by the finite volume method. The effects of operating conditions, such as the cooling water temperature. the system pressure, the film Reynolds number and the solution inlet concentration have been investigated in view of the absorption mass flux and the total absorption mass flux and the total absorption rate. The results for the temperature and concentration profiles, as well as the local absorption mass flux at the helical absorber are presented. It is shown that solution inlet concentration affected other than operation conditions for a mass flux.