• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.422-426
• /
• 2005

This experimental study represents the results of an analysis on the characteristics of flux density distribution in the focal region of solar concentrator. The characteristics of flux density distributions are investigated to optimally design and position a cavity receiver. This was deemed very useful to find and correct various errors associated with a dish concentrator. We estimated the flux density distribution on the target placed along with focal lengths from the dish vertex to experimentally determine the focal length. It is observed that the actual focal point exists when the focal length is 2.17m. The total integrated power and percent power was 2467W and $85.8\%$, respectively, in the case of small dish, and also 2095W and $79\%$, respectively, in the case of KIERDISH II. As a result of the percent power within radius, approximately $90\%$ of the incident radiation is intercepted by about 0.06 m radius. The minimum radius of receiver in KIERDISH II is found to be 0.15m and approximately $90\%$ of the incident radiation is intercepted by receiver aperture.

• 멤브레인
• /
• 제25권4호
• /
• pp.367-372
• /
• 2015

정삼투와 압력지연삼투 공정에서 용매의 투과율은 용매와 막이 접촉하는 방식에 의존한다. 각각의 공정에서 막의 활성층이 고농도 용매와 접촉하는 경우를 압력지연삼투 방식이라 하고, 고농도 용매가 막의 다공성 지지하층과 직면해 있는 경우를 정삼투 방식이라고 한다. 압력지연삼투 방식과 정삼투 방식은 각각 희석형 그리고 농축형의 내부농도 분극 현상을 유발하는데, 동일한 조작 조건에서 정삼투 방식보다 압력지연삼투 방식이 높은 투과율을 나타내는 현상이 실험적으로 관측되었다. 본고에서는 정삼투방식과 압력지연삼투 방식에서 발생하는 본질적인 투과율 불균형을 수학적 귀류법을 이용하여 증명하고, 물리적인 원인을 규명한다.

• Journal of Welding and Joining
• /
• 제19권4호
• /
• pp.391-398
• /
• 2001

MIAB welding method uses a rotating arc as its heat source and is known to be efficient in pipe butt welding. The arc is rotated around the weld line by the electro-magnetic force resulting from the interaction of arc current and magnetic field. This paper is concerned with the experiment of initial stage for process control, monitoring for weld quality, and the design of coil system which is efficient of flux generation and concentration. A coil system for the generation of magnetic flux was designed and constructed. Magnetic flux density and arc rotating behavior are important factors in MIAB welding, so the relations between these factors and process parameters were investigated. Various experiments were performed for the steel pipes(48.1mm O.D and 2.0mm thickness). The magnetic flux density is increased by increasing exciting current and decreasing gap size. The maximum of arc rotating frequency is affected by exciting current and gap size. However, the variations of arc rotating frequency during welding and then the melting process are mainly influenced by welding current. Thus, it is considered that the results of this study can be used as important data on the monitoring for weld quality and the design of efficient coil system.

• 멤브레인
• /
• 제11권4호
• /
• pp.161-169
• /
• 2001

Kaolin, bentonite, starch 및 PMMA의 단일 또는 혼합 입자용액을 정밀여과막이 장착된 dead-end 형 Amicon 여과셀에서 투과 실험하였으며 그 결과는 오염 특성을 규명하기 위하여 등압여과 모델에 적용하였다. 동일한 양으로 혼합한 kaolin/starch 입자의 0.1 wt% 혼합용액에 경우, 각각 입자의 평균 투과유속보다 30% 정도 낮았다. 그러나 kaolin보다 훨씬 큰 PMMA와의 혼합 입자용액의 경우에 투과유속은 kaolin과 PMMA의 평균보다 10% 정도 높았다. Bentonite와 PMMA 또는 starch의 혼합 용액일 경우, 혼합 입자에 의한 투과유속 향상효과는 kaolin에 비하여 훨씬 적게 나타났다. 또한 동일 양으로 혼합한 kaolin/starch 용액의 농도를 변화시킬 경우, 막오염 저항은 0.05 wt%에서 최소이었다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2022년도 학술발표회
• /
• pp.86-86
• /
• 2022

While estuarine dams can develop freshwater resources and block the salt intrusion, they can result in increased sediment deposition in the estuary. The mechanism of increased sediment deposition in an estuary with an estuary dam is not well understood. To fill this knowledge gap, 7 ADCP measurements of flow and suspended sediment concentration (SSC) were collected along-channel in an estuary with an estuarine dam over a neap-spring cycle. Flow and SSC were used to calculate the sediment flux and sediment flux gradients. The results indicated that the cumulative sediment fluxes at all stations were directed landward. The along-channel sediment flux gradient was negative, which indicated deposition along the channel. The landward mean-flow fluxes were dominant in the deep portion of the channel near the estuary mouth, whereas landward correlation fluxes were dominant in the shallow portion of the channel near the estuarine dam. The tides were the dominant forcing driving the sediment fluxes throughout the estuary.

• 환경영향평가
• /
• 제8권1호
• /
• pp.93-105
• /
• 1999

Lately water quality of Daechong Reservoir has become more eutrophicated than ever before and there has been much concern over especially the eutrophication of the embayment near Daejon and Chongju Water Intake Tower every summer. The purpose of this study is to predict the impact of change in the pollutant loading, flowrate, nitrogen and phosphorus release from sediment, SOD(sediment oxygen demand) upon the water quality of Daechong Reservoir by WASP5/EUTR05 in order to suggest water quality management alternatives. The data of Sep. 1995 were used for the calibration of the model and those of Sep. 1997 was for verification. The result of the modeling can be summarized as follows. 1. The 50% increase(decrease) of pollutant loading has caused that of T-N concentration by 0.10-0.14 mg/l, T-P concentration by 0.003-0.005 mg/l, and CBOD concentration by 0.16-0.18 mg/l. But the ratio of DO change by the change of pollutant loading was relatively small. 2. The sensitivity test of NH4 flux to T-N and that of P04 flux to T-P shows that T-N and T-P concentration were changed more in the epilimnion segments (SEG4, SEG5, SEG6, SEG7) than the other segments. As SOD increases, DO was predicted to decrease more especially in the hypolimnion (SEG9-SEG14). 3. As flowrate increase, the concentration of T-N, T-P, and CBOD were predicted to decrease, but DO concentration increased especially in the hypolimnion segments(SEG11, SEG12, SEG13, and SEG14). As the flowrate changed from $119m^3/sec$ to $50m^3/sec$, the concentration of T-N and CBOD in the hypolimnion was predicted to decrease.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 Proceedings of the second conference of aseanian membrane society
• /
• pp.155-160
• /
• 2004

Permeation experiments of a commercial nanofiltration membrane (nominated as ESNA 1) were carried out with aqueous solutions of various single salts, that is, five chlorides (NH$_4$Cl, NaCl, KCl, MgCl$_2$ and $CaCl_2$), three nitrates $(NaNo_3,\;Mg(No_3)_2\;and\;Ca(NO_3)_2)\;and\;three\;sulfates\;((NH_4)_2SO_4,\;Na_2SO_4\;and\;MgSO_4)$. The experimental results showed that (1) the permeate volume flux of the ESNA 1 membrane increased and decreased with the growth of the applied pressure and the feed concentration of salts, respectively. The real rejection of ESNA 1 membrane to most single salts increased with the growth of the permeate volume flux. (2) The reflection coefficients of ESNA 1 membrane to chlorides, nitrates and sulfates are 0.97, 0.96 and 0.99, respectively. The solute permeability of most salts except for magnesium and calcium salts increased with the growth of feed concentration. (3) The sequence of the rejections of ESNA 1 membrane to anions is $R({SO_4}^{2-})>R(CI)>R(NO_3)$ at the same feed concentration. While the sequence of the rejections to cations is cataloged into two cases: $R(Na^+)>R(K^+)>R(Mg^{2+})>R(Ca^{2+})$ at the concentration of 10 mol/$m^3$ and $R(Mg^{2+})>R(Ca^{2+})>R(Na^+)>R(K^+)$ at the concentration of 100 mol/$m^3$. The separation capability of a NF membrane is usually affected by the electrostatic effect and the steric-hindrance effect. In this case, the electrostatic effect is the major factor at low concentration and the steric-hindrance effect is the major factor at high concentration. Both the specific sorption and the hydration also reasonably influenced the separation performance of NF membrane to salts.

• 한국대기환경학회지
• /
• 제28권5호
• /
• pp.485-494
• /
• 2012

The purpose of this study is to monitor the flux of $CO_2$ and BVOCs (biogenic volatile organic compounds) between the atmosphere and forest. The main research activities are conducted at Taehwa Research Forest (TRF), managed by the College of Agriculture and Life Sciences at Seoul National University. The TRF site is located 60 km north-east from the center of Seoul Metropolitan Area. The TRF flux tower is in the middle of a Korean Pine (Pinus Koraiensis) plantation ($400m{\times}400m$), surrounded by a mixed forest. Eddy covariance method was used for $CO_2$ flux above the forest and REA (Relaxed eddy accumulation) method applying eddy covariance was used for BVOCs flux. BVOCs flux that was measured in spring (from May 16 to 18) had distribution of 84 to $2917{\mu}g/m^2{\cdot}h$. Especially, it showed that d-limonene being strong reactivity composed the largest fraction of monoterpene. Ambient $CO_2$ concentration measured in Mt. Taehwa was 399 ppm and observed $CO_2$ fluxes between the atmosphere and forest suggested that during the day, $CO_2$ is absorbed by plants through photosynthesis and released during the night.

• Journal of the korean society of oceanography
• /
• 제36권1호
• /
• pp.19-26
• /
• 2001

The biological pump is one of the important pumping mechanisms absorbing CO$_2$ from the atmosphere into the ocean and can be quantified by estimating new production. New production in the open ocean mostly depends on the supply of nitrate from the water below the mixed layer. While nitrate is affected by many biological processes, the helium isotope ($^3$He) is inert and has very simple physical properties. Using the $^3$He flux and the relation between $^3$He and NO${_3}\;{^-}$- within the thermocline, the nitrate flux supporting new production was estimated in the southern East Sea. The average ${\delta}^3$He within the mixed layer was -14$%_o$ and -l5.4$%_o$ in the winter and autumn, respectively. Through the year excess $^3$He occurs in the mixed layer except for a slight depletion of -17$%_o$ in summer. The $^3$He flux of 13$%_o$md$^{-1}$ associated with the concentration gradient at the air-sea interface was calculated from the product of the piston velocity and the excess $^3$He. Tritium decay within the mixed layer could support only 2$%_o$md$^{-1}$ of the flux. Thus, the remaining 11$%_o$md^{-1}$ could be attributed to the flux of tritiugenic $^3$He from the water below the mixed layer. Nitrate and $^3$He were positively correlated within the thermocline layer with the slope of 0.21 ${\mu}$mol kg$^{-1}$ $%_o\;^{-1}$. The annual nitrate flux estimated from the upward flux of $^3$He and the NO$_{3}\;{^-}$-$^3$He relation was 0.8${\pm}$0.2 mol(N) m$^{-2}$yr$^{-1}$. This flux corresponds to an annual new production of 64 g(C) m$^{-2}$yr$^{-1}$, which is consistent with that in the north-west Pacific.

• 한국환경보건학회지
• /
• 제28권2호
• /
• pp.117-129
• /
• 2002

Concentration of welding fumes and their components is known to be hazardous to welder and adjacent worker. To determine the generation rates of metals in fumes, $CO_2$ flux cored arc welding on stainless steel was performed in well designed fume collection chamber. Variables were different products of flux cored wire(2 domestic products and 4 foreign products) and input energy(low-, optimal- , high input energy). Mass of welding fumes was determined by gravimetric method(NIOSH 0500 method), and 17 metals were analysed by inductively coupled plasm-atomic emission spectroscopy(NIOSH 7300 method). Flux cored wire tube and flux were analysed by scanning electron microscopy to determine their metal composition. 17 metals were classified by their generation rates. Generation rates of iron, manganese, potassium and sodium were all above 50mg/min at optimal input energy level. Generation rates of chromium and amorphous silica were 25~50mg/min. At 1~25mg/min level, nickel, titanium, molybdenum, and aluminum were included. Copper, zinc, calcium, lead, magnesium, lithium, and cobalt were generated below 1 mg/min. Generation rates of metal components in fumes were influenced by input energy, types of flux cored wire. Flux cored wire was consisted of outer shell tube and inner flux. Iron, chromium, and nickel were the major components of outer tube. Flux contained iron, chromium, nickel, potassium, sodium, silica, and manganese. The use of flux cored wire can increase the hazards by increasing the amounts of fumes formed relative to that of solid wire. The reason might be the direct transfer of elements from the flux, since the flux is fine power. Ratio of metals to the fume of flux cored wire was lower than that of solid wire because non-metal components of flux were transferred. Total metal content of fumes in flux cored arc welding was 47.4(24.3~57.2) percent that is much lower than that of solid wire, 75.9 percent. We found that generation rates of iron, manganese, chromium and nickel, all well known to cause work related disease to welder, increased more rapidly with increasing input energy than those of fumes. To reduce worker exposure to fumes and hazardous component at source, further research is needed to develop new welding filler materials that decrease both the amount of fumes and hazardous components.