• Membrane Journal
• /
• v.17 no.2
• /
• pp.118-123
• /
• 2007

Performances of fluoropolymers related to membranes manufacturing for different purposes are reviewed in the present article. In particular the main physical, mechanical and chemical properties of PVDF, ECTFE and PFSA ionomers are described in their specific applications. The excellent chemical resistance and suitable electrochemical properties make fluoropolymers an especially good choice in membranes manufacturing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.369-369
• /
• 2012

The present work deals with selective deposition of copper on fluoropolymers patterned silicon (111) surfaces. The pattern of fluoropolymer was fabricated by nanoimprint lithography (NIL) and plasma reactive ion etching (RIE) was used to remove the residuals layers. Copper was electrochemically deposited in bare Si regions which were not covered with fluoropolymers. The patterns of fluoropolymers and copper have been investigated by scanning electron microscopy (SEM). In this work, we used two deposition methods. One is galvanic displacement method and another is electrodeposition. Selective deposition works in both cases and it shows applicability to other materials. By optimization of the deposition conditions can be achieved therefore this process represents a simple approach for a direct high resolution patterning of silicon surfaces.

• Membrane and Water Treatment
• /
• v.2 no.1
• /
• pp.39-49
• /
• 2011

We investigated about the utilization improvement of the PDMS and fluoropolymers by mutual application in environmental analysis. We were conducted the direct fluorination with mild condition on the PDMS films and analyzed its surfaces before and after fluorination. The results of FTIR and SEM analysis on the PDMS films showed that the film surfaces were fluorinated without irreversible deformation by the fluorination. During the fluorination, the measured contact angles of water and several alcohols on the PDMS films decreased with time and that of most alcohols decreased to 0 after 30 minutes. The surface energy of fluorinated PDMS films has increased by 2 times. Also, we investigated the influence factors on the change of permeation rate of water through PDMS tubes with time. It was observed that the change of permeation rate of water through PDMS tube was affected by temperature, water phase and spatial distribution of water. From these results, we could verify the principal causes of the decrease of permeation rate of water through PDMS tube with time and proposed a new experimental setup for reducing the variation of permeation rate of water less than 2%.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2001.05a
• /
• pp.88-92
• /
• 2001

• Korea-Australia Rheology Journal
• /
• v.15 no.4
• /
• pp.173-178
• /
• 2003

Boron nitride is a new processing aid that is capable of eliminating gross melt fracture in several polymer processing operations. Its combinations with other processing aids i.e. fluoropolymers offer additional possibilities of obtaining enhanced processing aids that may take the processes to rates not realized before. A variety of different such combinations are discussed in this paper. The essential componenets are (1) boron nitride capable of eliminating gross melt fracture and (2) suitable lubricant capable of eliminating surface melt fracture such as stearates for the polyolefin processing and polyethylenes for the processing of fluoropolymers.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.41-48
• /
• 2011

The wettabilities of the partially fluorinated polymers (ethylene-tetrafluoroethylene copolymer (ETFE), ethylenechlorotrifluoroethylene copolymer (ECTFE), and poly(vinylidene fluoride) (PVDF)) were investigated by contact angle measurements. Zisman plots for ETFE and ECTFE exhibited linear relationships, while the Zisman plot for PVDF showed a slight curvature, which was interpreted to indicate strong non-dispersive interactions between the surface and the contacting liquids. The Lifshitz-van der Waals forces of the fluoropolymers were estimated to increase in the order of ETFE < PVDF $\ll$ ECTFE. An evaluation of the polar or "acid-base" interaction energies showed that PVDF, which possesses the most acidic hydrogens among the examined fluoropolymers, has the strongest acid-base interactions.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.37-43
• /
• 2001

Polyvinylidenefluoride and Polytetrafluoroethylene have been irradiated by 1 keV Ar+ ion beam in an $O_2$ environment. Hydrophilic functional groups (such as -(C-O)-,-(C=O)-,-(C=O)-O- and so on) were formed on fluoropolymers. Contact angles of water to PVDF were reduced from $75^{\circ}$ to $31^{\circ}$. Re-increase of contact angle was originated from carbonization phase in case of high dose irradiation above $1{\times}10^{16} Ar^+cm^2$. Contact angles to PTFE decreased at low dose irradiation and were exaggerated to about $140^{\circ}$ due to cone type surface at high dose irradiation. Hydrophilic functional groups have played an important role on adhesion between metal and fluoropolymers by acid-base interaction and chemical bond formation. Adhesion of Pt/PVDF was enhanced by acid-base interaction because Pt is inert metal. Chemical bond formation between Cu and PTFE could enlarge the adhesion strength of Cu/PTFE.

• Polymer(Korea)
• /
• v.38 no.4
• /
• pp.457-463
• /
• 2014

In this study, the changes in the chemical structure and the physical property of fluoropolymer films (PTFE, FEP, PFA, PVDF, and ETFE) induced by $Co^{60}$ gamma ray in air, $N_2$, and vacuum environments were investigated. FTIR spectra of the irradiated fluoropolymers indicate that the oxidation proceeded by the reaction of radicals generated by irradiation with oxygen in air. The changes in the heat of fusion and the degree of crystallinity of the irradiated fluoropolymers were investigated using DSC and the results indicate that the scission and crosslinking reactions of the irradiated fluoropolymers were largely influenced by the chemical structure. It was also found that the mechanical property of the irradiated fluoropolymer films under an air atmosphere was significantly decreased.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1996.04a
• /
• pp.34-35
• /
• 1996

The diffusional behavior of many non-solvents in glassy or semicrystalline polymers cannot be adequately described by a concentration-dependent form of Fick's law, especially when mass transfer is coupled with structural changes. Many mathematical models have been devised to interprete non-Fickian diffusion dominated by relaxation kinetics. In formulation of non-Fickian diffusion mathematics, therefore, the most important factor to consider is how relaxation effects can influence the governing constitutive equation and boundary conditions. That is, relaxation parameters can be accommodated by variable boundary conditions or a modified continuity equation, or both, depending on specific systems and conditions (Frish, 1980). Accoring to Astarita and Nicolais (1983), the model equations can be broadly categorized as continuous or discontinuous. Continuous model equations encompass phenomena where the structural change takes place gradually over the whole volume of the polymer sample (Crank, 1953; Long and Richman, 1961; Berens and Hopfenberg, 1978). On the other hand, discontinuous model equations deal with the phenomena where the morphological change appears to be abrupt (Li, 1984). Four mathematical models with different relaxation parameters were applied to fit the anomalous sorption data observed in fluoropolymers (PVDF, ECTFE). The fitted result for PVDF-benzene sorption data is shown in Fig. 1.

• Journal of the Korean Home Economics Association
• /
• v.35 no.4
• /
• pp.257-268
• /
• 1997

The effects of water-and oil-repellent finishes on the deposition and removal of oily soils from polyseter fabrics were investigated in this study. The polyester fabrics treated with three kinds of fluoropolymers(TG-410H, TG-990) were soiled with mixed oily soils and washed by using Terg-O-Tometer at various conditions. It was found that TG-410H and TG-527 treated polyester fabrics reduced significantly the deposition of oily soils than untreated and TG-990 treated polyester fabrics. The removal of oily soils from polyester fabrics was increased in porportion to increasing of surfactant concentration up to a certain point(0.2% owb) but it levelled off above the point. The removal effect was high in the order of TG-990 treated polyester fabrics > untreated polyester fabrics > TG-527 treated polyester fabrics > TBG-410H treasted polyester fabrics. Especially the removal of oily soils from polyester fabrics was more effectively removed in triton X-100 solution. In general the removal of oily soils from polyester fabrics treated with fluoropolymers was increased up to a miximum near 6$0^{\circ}C$ and than decreased above 6$0^{\circ}C$. And efficient removal could be achieved within relatively short time (30min) The removal of oily soils from polyester fabrics was increased in proportion to increasing of pH range up to a certain point(9.5 or 11.0) but it began to decrease above the point. Furthermore the removal of oily soils was increased with th increase of mechanical agitation, but it began to decrease above 160 rpm.