• 한국정밀공학회지
• /
• 제21권1호
• /
• pp.87-93
• /
• 2004

Recently, with the development of bio-technology the interests in the micro-fluidic devices for analysis in the fields of biology and medical science have been steadily increasing. Although polymer is considered as one of the best materials for micro-fluidic devices. glass or silicon molds fabricated by photo-lithographic technique have been commonly used. However, it is generally perceived that the conventional photolithographic technique has the limitation for fabricating micro-channels for micro-fluidic devices. In this work, the possibility of fabrication of micro-fluidic channels on PDMS by using the mechano-chemical process and the effect of surface states on the fluid flow were investigated. Experimental results revealed that PDMS mold fabricated by the mechano-chemical process could be used effectively to replicate micro-fluidic channels with high reproducibility and dimensional accuracy. It was also found that the fluid flow generation and flow speed were largely affected by the hydrophilicity and the surface roughness of the micro-channel surfaces.

• 대한기계학회논문집B
• /
• 제38권1호
• /
• pp.9-16
• /
• 2014

본 논문은 경사진 원형관에서 표면장력과 중력으로 구동되는 비뉴턴 유체(멱법칙 모델)의 유동 및 변위를 이론적으로 연구한 것이다. 그리고 표면장력에 의하여 연속적으로 원형관 내로 유입되는 비뉴턴 유체의 변위를 기술하기 위한 지배방정식을 처음으로 개발하였다. 뉴턴의 운동방정식으로부터 유도된 식은 2계 비선형이며 비제차인 형태의 상미분 방정식이다. 지배방정식의 해를 수평관에서 변위를 시간의 함수로 기술한 식 및 실험과 비교한 결과 정량적으로 동일한 일치를 보였다. 여기에 더하여 정상상태인 힘의 균형식의 결과에 대해서도 정확한 일치로 나타남을 확인할 수 있었다.

• 대한기계학회논문집B
• /
• 제26권11호
• /
• pp.1513-1520
• /
• 2002

Effect of Convex Surface Curvature on the Onset of Nucleate Boiling of Subcooled Fluid Flow in Vertical Concentric Annuli An experimental study has been carried out to investigate the effect of the transverse convex surface curvature of core tubes on heat transfer in concentric annular tubes. Water is used as the working fluid. Three annuli having a different radius of the inner cores, Ri=3.18mm, 6.35mm, and 12.70mm with a fixed ratio of Ri/Ro=0.5 are used over a range of the Reynolds number between about 40,000 and 80,000. The inner cores are made of smooth stainless steel tubes and heated electrically to provide constant heat fluxes throughout the whole length of each test section. Experimental result shows that heat flux values on the onset of nucleate boiling of the smaller inner diameter model is much higher than that of the larger size test model.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.30-36
• /
• 2013

An FFD(flexible fine die) is an embossed mold that consists of a thin plate ranging from 0.6 to 3 mm in thickness. FFDs are primarily used for cutting LCD films and F-PCB sheets. In the high-speed micro-milling process of flexible fine dies, the lubrication and cooling of the cutting edges is very important from the aspect of eco machining and cutting performance. In this paper, a comparative study of tool wear and surface roughness between cutting fluid and hybrid lubrication for eco-machining of FFD was conducted for processes of high-speed machining of highly hardened material (STC5, HRC52). Especially, the incorporated fluid method for eco machining, in which the cutting performances can be simultaneously measured, was introduced. The machining results show that hybrid lubrication, instead of conventional cutting fluid, leads to excellent tool wear and surface roughness and represents the proper conditions for eco micro-machining of flexible fine dies.

• 한국공작기계학회논문집
• /
• 제12권2호
• /
• pp.23-30
• /
• 2003

It is very important to detect and evaluate the surface or subsurface flaws because of their influences on mechanical properties of materials. Rayleigh wave and creeping wave are commonly used for the detection of surface and subsurface flaws. These techniques, however, have following problems. Each amplitudes are remarkably affected by the surface condition and evaluation of echo pattern is usually difficult because shear wave mode propagate in the material at the same time. On the other hand, surface SH-wave which is horizontally polarized shear wave traveling along near surface layer is an attractive technique for the surface or subsurface material characterization and this technique is useful to solve the problems mentioned above. In this paper, The stability and transmission coefficient of SH waves through a viscous fluid layer is theoretically studied and simulated. Its results agreed well with the theoretical expectation for the experimental verification. These experimental results show that viscosity of couplants, thickness of couplant and surface roughness are closely related to transfer efficiency in surface SH angle beam method.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.67-72
• /
• 2002

Today, the research to examine a fact that interaction between the air and the fluid free surface affects the steady state flow and air. We proved the interaction between vortex pairs and free surface on each condition that is created by the end of delta wings. another purpose of this study is to investigate the effect of surface active material which can change the surface tension and we must consider when we refer to turbulent flow on surface tension. therefore, this research examined the growth process of vortex pairs on condition of clean, contaminated free surface and wall after we made vortex pairs through counter rotating flaps. The results of this study suggest that vortex pairs in clean free surface rise safely but the vortex pairs in contaminated free surface and rigid, no slip is made secondary vortex or rebounding. However the secondary vortex in rigid, no slip is stronger than before, and we can find the vortex shape which roll up more completely. However, these will disappear by the effect of wall.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1995년도 추계 학술대회논문집
• /
• pp.126-131
• /
• 1995

In this paper we study steady capillary-gravity waves in a two-layer fluid bounded above by a free surface and below by a horizontal rigid boundary with a small obstruction, Two critical speeds for the waves are obtained. Near the smaller critical speed, the derivation of the usual forced KdV equation (FKdV) fails when the coefficient of the nonlinear term in the FKdV vanishes. To overcome this difficulty, a new equation called a forced extended KdV equation (FEKdV) governing interfacial wave forms is obtained by a refined asymptotic method. Various solutions and numerical results of this equation are presented.

• 전기학회논문지
• /
• 제56권12호
• /
• pp.2173-2178
• /
• 2007

Dynamics of plasma sheath was analyzed using simple ion fluid model with poison equation. Incident ion current, energy, potential distribution and space charge density profile were calculated as a function of time. The effects of initial floating sheath on the evolution of biased sheath were compared with ideal matrix sheath. The effects of finite rising time of pulse bias voltage on the ion current and energy was studied. The influence of surface charging on the evolution of sheath was also investigated

• Wind and Structures
• /
• 제14권5호
• /
• pp.435-447
• /
• 2011

A Computational Fluid Dynamics model is presented in this study for the simulation of the complex fluid flows with free surfaces inside the Tuned Liquid Column Dampers in horizontal motion. The characteristics of the fluid model of the TLCD in horizontal motion include the free surface of the multiphase flow and the horizontal moving frame. In this study, the time depend unsteady Standard ${\kappa}-{\varepsilon}$ turbulent model based on Navier-Stokes equations is chosen. The volume of fluid (VOF) method and sliding mesh technique are adopted to track the free surface of water inside the vertical columns of TLCD and treat the moving boundary of the walls of TLCD in horizontal motion. Several model solution parameters comprising different time steps, mesh sizes, convergence criteria and discretization schemes are examined to establish model parametric independency results. The simulation results are compared with the experimental data in the dimensionless amplitude of the water column in four different configured groups of TLCDs with four different orifice areas. The predicted natural frequencies and the head loss coefficient of TLCDs from CFD model are also compared with the experimental data. The predicted numerical results agree well with the available experimental data.

• 소성∙가공
• /
• 제22권2호
• /
• pp.80-85
• /
• 2013

The surface integrity of micro-machined products affects the performance of products significantly. Micro-burrs resulting from micro-cutting degrades the surface quality. Therefore it is desired to eliminate them completely and many studies have been undertaken for this purpose. In this study, micro-end-milling was carried out on nickel alloy and brass materials commercially used for light guide plate mold in 3-D optical devices. After completing this micro-machining, the burr heights were measured with a microscope. Then, deburring was done on the machined edges using the MR jet polishing method. A jet angle of $0^{\circ}$ and deburring times of 1, 3, and 5 min. were chosen. It was found that burrs were completely eliminated after 5 min of MR fluid jet polishing.