• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.91-91
• /
• 2009

Piezoelectric micro-pump should contain the physical running parts like check valves for acquiring the unilateral motion of fluid from the alternating motion of actuators. But the check valves raise many problems such as abrasion or exhaustive destruction by the recursive mechanical displacement To solve these problems, we propose a novle type piezoelectric valveless micro-pump using peristaltic motion due to the traveling wave excitation. Proposed pump model is consisted of two piezoelectric ceramic plates, elastic metal body, caps for covering flow path, rubber rings for sealing tightly and disk springs for the pressurization of pump body.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1038-1041
• /
• 2004

In this study, developed a micro-level experimental setup to measure pore pressure and poroelastic modulus in various strain and strain rate about a stress in micro-structure of bone tissue. It is essential device in the development of the model to analysis the interstitial bone fluid flow of the lacuno-canalicular system to be known that would effect on the bone remodeling. The constitution of the experimental setup is as follows, microscopic image processing system; actuator control unit; load measurement system. A pilot study was used an artificial chemical wood to have similar poroelastic property of bone matrix and conducted to validate the suitability of the measurement system.

• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.135-141
• /
• 1998

Some sized centrifugal compressor were designed and their performance measured to investigate the effects of exit blade thickness, width and back swept angle. The impeller of larger blade thickness shows low pressure ratio compared with that of smaller one. Backswept angle have also large effect on the efficiency. Measured values of slip factor are quite different from the estimated values of Wiesner-Busemann model and increase with the flow rate.

• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.57-63
• /
• 1998

The performance of a centrifugal fan depends on the dimensional parameters of impeller, such as the inlet and exit diameter, area ratio, relative flow angles to the blade, and number of blades. These design parameters, however, are inter-related, so it is very difficult to identify the effect of each parameter to the fan performance. In this experimental study the effect of the design parameters on the performance of a small centrifugal impeller being used for vacuum cleaners are investigated. Total 30 shrouded impellers with 120mm diameter were tested and the results were non-dimensionalized to compare their performance.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.435-440
• /
• 2007

Fish-mimetic robots or fish-mimetic propulsors have been developed or under construction. A mechanical system cannot have the same functions as bio-organic systems. Thus, the hydrodynamic characteristics of fish locomotion should be well understood in order to develop and control a feasible intelligent fish-mimetic robot with its optimal motion pattern known. In this paper, a mackerel-mimetic robot fish is fabricated in order to understand the hydrodynamic characteristics of fish locomotion. A simplified unsteady flow theory is also applied to the hydrodynamic analysis of the motion of the anterior part of the robotic fish. The normal and axial forces of the fish are measured by changing the amplitude and frequencies of fanning motion. It is found that the present theoretical results agree with the measured data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.469-472
• /
• 2007

Aeroacoustic sound induced from inter-couch spacing is an important contributor to interior noise generation for high speed trains. Especially the open space between mud-flap has significant impact from flow-structure interactions. To understand noise generation mechanism, experiments were performed using the wind tunnel. To find mud-flap parameters for minimal noise generations the various shape of the mud-flap was installed and its effects on the wall-pressure generation were investigated.

• 한국기계연구소 소보
• /
• v.4 no.2
• /
• pp.49-63
• /
• 1982

In this paper, a classical gust problem is treated by using the numerical lifting¬-surface theory to verify the effect of gust-a sudden fluctuating fluid velocity around an object, which is normal to the main stream direction-on the hydrody¬namic forces, especially the mean thrust in upstream direction, acting on the two¬-dimensional flat plate. In this case, the mean thrust wholly resorts to the leading edge suction, and it is the same situation to the case of the heaving plate in uniform flow. The ph¬enomenon of leading edge suction is very important for the flapping propulsion of animals, typical to fish and birds, and can be related to the prediction of the hydrodynamic forces acting on marine propellers operating in gustlike wakes of ships. The results of this paper can be easily superposed to those of the reference [1J in order to solve the problem of the two-dimensional oscillacting plate in gust

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.2
• /
• pp.155-164
• /
• 1998

A multi-type heat pump controls the mass flow rate of the working fluid to cope with variable heat loads when it is under dynamic load condition. This paper describes the exergy analysis associated with the dynamic response of heat pump. First, a basic heat pump cycle is examined at steady state to show the general trends of exergy changes in each process of the cycle. Entropy generation issue in the exchangers is discussed to optimize the heat pump cycle. Second, the performance of the inverter-driven heat pump is compared to that of the conventional one when the heat load is variable. Third, the exergy destruction rate associated with the ON/OFF operations of the heat pump is calculated by simulating the thermodynamic states of the condenser and the evaporator. The inefficiency of the ON/OFF operation during the transient period is quantitatively revealed by the exergy analysis.

• Nuclear Engineering and Technology
• /
• v.30 no.1
• /
• pp.17-25
• /
• 1998

Transport of carbon and boron impurity ions parallel to magnetic field lines in the tokamak SOL (scrape-off layer) is numerically investigated for a one-dimensional steady state. The spatial distributions of density and velocity of the impurity ions in a steady state are calculated by finite difference method for a single-fluid model. The calculated results show that among forces acting on SOL particles thermal force produced tv plasma temperature gradient is a principal force determining the feature of impurity distribution profiles in the tokamak edge. However, strong collisional friction forces appearing dominant in front of the diverter plate restrain impurity ion flows due to temperature gradients from moving toward the midplane. Consequently, the stagnation point develops in the impurity flow by these two forces near the diverter region, in which ion flows change their directions. Impurity ions turn out to be accumulated at the stagnation points, where peaked profiles of highly-ionized state ions are relatively predominant over those of low-ionized state ions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.212-217
• /
• 1998

Reynolds equation, which describes behavior of fluid film in journal bearing, basically satisfies mass conservation. But, boundary conditions usually used with this equation, e.g. half Sommerfeld or Reynolds boundary conditions, cannot fulfill this natural law of conservation. In the case of connecting rod bearing, where applied load is dynamic and its magnitude is relatively large, such unrealistic boundary conditions have serious influence on calculation results, especially on lubricant flow rate or power dissipation which are important parameters in thermal analysis. Another important factor in the analysis of connecting rod bearing is elastic deformation of bearing support structure which is relatively flexible. In this paper, EHL analysis of connecting rod beating is performed using mass-conserving boundary condition. Elastic deformation of bearing support structure and application of mass-conserving boundary condition have significant effects on the performances of connecting rod bearing.