• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.90-94
• /
• 1996

Thermal problems of creep-feed grinding are more serious than regular grinding. So grinding fluid supply in creep-feed grinding is very important. Grinding fluid supply quantity is not linear with effectiveness because grinding wheel is porosity material and the grinding area is solid contact area. In this paper, by using AE signal, optimal quantity of fluid supply was determined. And surface characteristics of wet creep-feed grinding were analized.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.857-861
• /
• 1997

In discontinuous wheel grinding, temperature is different form conventional grinding. The characteristics of discontinuous grinding with respect to various slotted wheel were compared with those of general grinding. Thermal conditions vary with intermittent ratio, direction of fluid supply for discontinous wheel. According to three direction of grinding fluid supply and intermittent ratio,temperature and surface roughness were analyzed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.453-464
• /
• 2002

The electrorheological(ER) fluid is a new material and is used for the mechanical motion devices such as semi-active suspensions, high speed clutches, and vibration isolators. The ER fluid applications need high voltage power supplies having special requirements to control the viscosity of the ER fluid. This paper deals with the development of the high voltage power supply for the semi-active suspension system using the ER fluid. The characteristics of the ER fluid are analyzed, and the design and implementation of the high voltage power supply are presented. It is well demonstrated through the experiment that the developed high voltage power supply shows a good performance suitable for the ER fluid application.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.1
• /
• pp.25-31
• /
• 2003

This paper addresses an oil supply enhancement device to resolve a shortage of oil supply or no oil supply at all encountered at low speed operation for a variable speed reciprocating compressor used for household refrigerators. The oil supply enhancement device comprises a moving cylinder attached to the lower end of crankshaft and two of fluid diodes, each one at the inlet and outlet of the cylinder. Up-and-down movement of the cylinder against the lower end of the crankshaft together with the functioning of the two fluid diodes produces net oil flow from oil reservoir to inside the crankshaft. The experiment on the test bench has shown that enough oil supply into the oil feeding hole cu be made by using this device even at low speed range. Some analytical study has also been carried out to under-stand its oil supply mechanism.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.544-549
• /
• 2001

The effect of power supply voltage on the performance limits in a laboratory Magneto-rheological fluid based device was identified by experiments. It suggests that the frequency range of motion for control be limited by the voltage attenuation due to the coil inductance and the maximum power supply voltage set for practical use of MRF devices. In this work, the magnetic and electrical characteristics of MRF device are investigated and a design procedure is formulated to achieve the desired performance for a given power supply.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1517-1523
• /
• 2001

The effect of power supply voltage on the performance limits in a laboratory magneto-rheological fluid based device was identified by experiments. It suggests that the frequency range of motion for control is limited by the voltage attenuation due to the coil inductance and the maximum power supply voltage set for practical use of an MRF devices. In this work, the magnetic and electrical characteristics of the MRF device are investigated and a design procedure is formulated to achieve the desired performance for a given power supply.

• Fire Science and Engineering
• /
• v.33 no.5
• /
• pp.28-36
• /
• 2019

In the present study, the effects of supply gas and water mist on the heptane pool fire extinguishing performance were investigated using the full cone and hollow cone twin-fluid atomizers. Air or nitrogen of 30 lpm (Liter per minute; L/min) was used as the supply gas, and the experiments were conducted under the water flow rate conditions of 0 lpm (i.e., discharge of air or nitrogen only) and 0.085 lpm (i.e., discharge of water mist with supply gas). Experimental results confirmed that the use of water mist discharge with the supply gas and full cone spray pattern reduced the fire extinguishing time as compared to that of only supply gas discharge and hollow cone spray pattern. In addition, for the discharge of water mist using the full cone twin-fluid atomizer, water mist significantly affected fire extinguishing performance, whereas the effect of the supply gas was less pronounced. On the other hand, for the discharge of water mist using the hollow cone twin-fluid atomizer, the fire extinguishing time was remarkably reduced by the supply of nitrogen, as compared with that of air, indicating that the supply gas as well as water mist can significantly affect fire extinguishing performance.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.206-208
• /
• 2002

Metalworking fluids (MWFs) are fluids used during machining and grinding to prolong the life of the tool , carry away debris, and protect the surfaces of work pieces. These fluids reduce friction between the cutting tool and the work surface, reduce wear and galling, Protect surface characteristics, reduce surface adhesion or welding and carry away generated heat. Workers can be exposed to MWFs by inhaling aerosols (mists) and by skin contact with the fluid. Skin contact occurs by dipping the hands into the fluid, splashes, or handling workpieces coated with the fluids. The amount of mist generated (and the result ins level of exposure) depends on many factors. To reduce the potential health risks associated with occupational exposures to MWFs, it is required to establish optimum MWFs supply method and condition with minimum Quantity in all over the mechanical machining field including high speed type heavy cult ing process.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.5 s.32
• /
• pp.22-28
• /
• 2005

As the water supply facilities are recently getting larger, the domestic waterworks become multi-regional water supply system. Large water supply facilities generally consist of the intake pumping station, water treatment plant and water supply/distribution facilities. Although the pumping stations and the pipeline systems are used to pump up water, it often happens pipeline damage and flooding accident by the water hammer. In this paper, the intake pumping station is guaranteed by both the computer simulation and the field test analysis. This study is contributed to the safe operation program for the pumping station in which results of the adjustment on the safety plan of the pumping station, the air valve and the valve closing time.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.98-107
• /
• 1999

In this work the effect of pressure drop at inner film due to centrifugal forces acting on the lubricating fluid is investigated for static and dynamic characteristics of floating ring journal bearing. The momentum effect of oil supply into a inner film through oil feeding holes of floating ring on the bearing performance is also studied. It is compared the pressure drop effects and the momentum effect of oil supply into a inner film fur all bearing performance parameters. It is shown that some performance of floating ring bearings can be controled by the momentum of oil supply into a inner film.