• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.3
• /
• pp.150-157
• /
• 2002

This paper presents preliminarily an implementation of digital high-performance motion control system of Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consist of stator flux observer, torque estimator, two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source inverter, and TMS320F240 DSP controller made by Texas Instruments. The stator fluff observer is based on the combined voltage and current model with stator flux feedback adaptive control, and the input of the observer are the stator voltage and current of motor terminal for wide speed range. The rotor position and speed sensor used 6000 pulse/rev encoder. In order to prove rightness of the suggested control algorithm, we have some simulation and actual experimental system at $\pm$20 and $\pm$2000 rpm. The developed digitally high-performance motion control system+ are shown a good response characteristic of control results and high performance features using 1.0kW RSM which has 2.57 Ld/Lq salient ratio.

• Fashion & Textile Research Journal
• /
• v.22 no.6
• /
• pp.803-811
• /
• 2020

This study investigates the management of clothes and the perception of up-cycling fashion based on university students majoring in fashion. Results based on 124 survey participants are as follows. First, students prioritized design when buying clothes and regarded texture as important for material. In managing clothes, male students emphasized durability; however, female participants checked fluff occurrence. Second, more than half of the respondents knew what up-cycling fashion was; overall, female students were more aware of up-cycling fashion than males. Few students purchased up-cycling clothes; however, many were willing to buy up-cycling clothes for eco-friendliness, which implies that they understood the relations between up-cycling fashion and environment. Third, pertaining to the perception of SPA fashion, students were highly satisfied with the accessibility of SPA brand stores. The group of students who knew up-cycling fashion were more satisfied with SPA brands and indicated o correlation between the cognition of up-cycling brands and preference for SPA brands. Last, in terms of the perception of environment and clothing, university students majoring fashion recognized the need for environmental protection; however, they did not emphasize environment when purchasing or managing clothes.

• Journal of the Korean Society of Costume
• /
• v.58 no.10
• /
• pp.65-77
• /
• 2008

The purpose of this study is to analyze the correlation between the density, the Count and the width of cross section in 2D function through comparison the difference of simulated fabrics based on the various yarns, and to compare the 3D effect by Lay Mapping of diverse fabrics. The method of research is to weave the eight fabrics composed of cotton, linen, worsted, slender yarn, loop, $m{\acute{e}}lange$, woolen, and yarn twist with Hi-Tex program, and to practice 3D mapping with Hi-Print program. As a mapping object, the flared skirt which is a basic costume item is selected. As a result, the thickness of yarn in CAD system was fixed by the width of cross section rather than Count, especially by the width of core section not including the fluff section. The type of yarn such as cotton yarn, linen yarn, and worsted had effect on the shape of texture, but had few interrelations with dimension. In the case of 3D mapping, the textural characteristic and the dimension were presented precisely, whereas there were several limitations. First, the thickness of tissue has not been represented. Secondly, the effect of texture such as fuzzy look, loop was not expressed on the skirt outline including sideline and hemline. Thirdly, the difference of silhouette was not distinct. The common point in 2D and 3D operations is that the representation of texture is relatively accurate and that is difficult to measure and manifest of thickness, the side. For more professional digitalizing in fashion industry, above all in the domain of 3D, it must be supplement the subdivided and differentiated mapping process according to the texture, deviating from the existing analog-based organization which has to designate the form and silhouette suitable for tissue.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.23 no.4
• /
• pp.499-509
• /
• 1999

This study was carried out to investigate the effects of wearing disposable diaper with the endothermic agent on thermoregulatory response of infant. Five healthy female infants aged about 5 months were taken as a subject of this experiment. Experimental diapers were six kinds of disposable diaper constructed of nonwoven tissue, fluff pulp, super absorbent polymer, back sheet film, leg elastic, and 0g urea(A) 1g urea(B) , 2g urea(C), 3g urea (D), 4g urea(E) 5g, urea(F) respectively. Urea(98% or over purity) was used as an endothermic agent. Experiment was proceeded while infants were sleeping at 27.5$\pm$0.5$^{\circ}C$, 50$\pm$5% R.H, 0.04m/sec. Each disposable diaper's properties was tested. During the experiment rectal temperature skin temperature of 9 areas temperature inside the disposable diapers were measured, the results were as follows : 1) There was not significant difference among the diapers in absorption capacity retention capacity and rewet(p=0.05). The absorption under load was showed to A, B,

• Resources Recycling
• /
• v.17 no.3
• /
• pp.10-20
• /
• 2008

In order to study the behaviors of inorganic fillers in recycling of the waste agricultural plastic films, the washed PE fluffs from Shihwa and Jungeup Plant belonging to ENVICO were used respectively. First of all, the test pellets were manufactured by adding of inorganic fillers suchlike calcium carbonate and calpet by certain portions to PE fluffs and then the tested sheets were formed. The mechanical and thermal properties of the samples were measured and compared with others. The items measured were tensile, flexural, Izod impact, HDT, MFT, and so on. Morphologies were also investigated for various samples using the SEM. Finally, optimum ratios between recycled PE and inorganic additives were found out for the best products in physical condition as well as in economic point of view.

• The Korean Journal of Mycology
• /
• v.47 no.2
• /
• pp.143-152
• /
• 2019

A new cultivar 'Sanjanghyang' was bred from monokaryotic strains of 'Sanbaekhyang' and 'Jangan 1ho'. Pileus was flat, round, and reddish brown. The diameters of the pilei and stipe length of the fruiting bodies were 67.1 mm and 16.9 mm, respectively. The scales were white or slightly brown and distributed evenly. The gill density was sparse and showed a rippled texture. The stipe was cream in color and the fluff was medium. 'Sanjanghyang' had a short cultivation period and fruiting bodies occurred sporadically. Temperature for fruiting body formation was a medium, between 15 to $19^{\circ}C$. 'Sanjanghyang' was different from 'Sanbaekhyang' with regard to its pileus diameter (67.1 mm) and autumn and spring fruiting body production period. 'Sanbaekhyang' had pileus diameter of 74.7 mm, and fruiting body formation occurred in spring and autumn. The rate of fruiting body formation was 89% (first flush), 4% (second flush), and 7% (third flush).

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.351-358
• /
• 2011

This study has been carried out to understand the fracture characteristics of the tension wood of Quercus mongolica under the shear and bending stress. Macroscopically, the wood fluff in the shear surface appeared more frequently in tension wood than sound wood, and more coarse wood fluffs were observed in 30% than 10% moistured shear surface. In the fractured tension wood from bending stress, more thick and long wood fiber appeared than sound wood. The observation using scanning electron microscope indicated that both sound and tension wood samples from radial shear surface showed the intrawall dominated failure and the fracture surface of the ray parenchyma cell showed the transwall dominated failure. In tangential shear surface, wood fiber surface showed the intrawall failure and short and coarse wood fiber was observed in tension wood. Ray parenchyma cell of sound and tension wood samples showed the transwall failure. The surfaces of tension wood’s ray parenchyma cell were relatively clean. The fractured tension wood from bending stress showed unsharp and flat wood fiber compared with sound wood.

• Resources Recycling
• /
• v.21 no.1
• /
• pp.17-29
• /
• 2012

potential assessment of converting closed non sanitary landfills into sustainable landfill through the reclamation works(= landfill mining project) of illegal landfill discovered in land development site using Sustainable Landfill Reclamation system(SLR-system) was investigated. The SLR system had treatment capacity of 91.4 $m^3/hr$ (130.61 ton/hr) in condition of 28.0% of water content. Recovery ratio and purity of sorted soil were 98.9% and 99.66%, respectively. Sorted combustibles were 91.8% and 92.0%, respectively. Especially, high heating value (HHV) and low heating value(LHV) of combustibles were 4,282kcal/kg and 3,636 kcal/kg, respectively, in considering the energy content and recovery ratio of combustibles. Therefore, combustibles separated from landfill site have higher value than Fluff RDF standard value(3,500kcal/kg) of MOE. RDF can be produced with combustibles by 84.43%. Averaged size and organic foreign matter content of the sorted soil were less than 035mm and 0.31 %(VN), respectively. In addition, concentration of all contents of hazardous matters containing soils met safety standards. Therefore, it is possible to be recycled as refilling and cover materials to rebuild Sustainable landfills by 98.42%.