• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2006년도 추계학술대회 논문집
• /
• pp.42-47
• /
• 2006

The flow around a rotating circular cylinder near a plane wall is investigated by the measurement of the lift acting on the cylinder and by the flow visualization using the hydrogen bubble technique in the circulating water tank. The experimental parameters are the rotating direction of the cylinder, the space ratios H/D$(H/D=0.05\sim0.5)$ between cylinder and plane wall and the velocity ratios $\alpha(\alpha=0\sim{\pm}2.0)$. In the case of clockwise, the lift on the rotating circular cylinder was increased with the reduction of the space ratios and with the velocity ratios, the upper separation point was more shifted in the rotating direction with them. In the case of anticlockwise, the absolute value of the lift on the rotating circular cylinder was increased with the space ratios and with the velocity ratios, the lower separation point was more shifted in the rotating direction with them.

• Advances in aircraft and spacecraft science
• /
• 제9권1호
• /
• pp.1-15
• /
• 2022

This paper presents calibration of flush air data sensing systems during ascent period of a satellite launch vehicle. Aerodynamic results are numerically computed by solving three-dimensional time dependent compressible Euler equations over a payload shroud of a satellite launch vehicle. The flush air data system consists of four pressure ports flushed on a blunt-cone section of the payload shroud and connected to on board differential pressure transducers. The inverse algorithm uses calibration charts which are based on computed and measured data. A controlled random search method coupled with neural network technique is employed to estimate pitch and yaw angles from measured transient differential pressure history. The algorithm predicts the flow direction stepwise with the function of flight Mach numbers and can be termed as an online method. Flow direction of the launch vehicle is compared with the reconstructed trajectory data. The estimated values of the flow direction are in good agreement with them.

• 마이크로전자및패키징학회지
• /
• 제23권4호
• /
• pp.87-92
• /
• 2016

전자소자의 방열모듈에서 두께 방향의 열방출 특성에 대한 중요성이 증가하고 있다. 금속과 금속의 본딩 및 유전체와 금속의 본딩 구조를 갖는 2가지 종류의 2층 층상재료를 제조한 후 두께 방향으로 열확산계수를 측정하였다. 금속(STS439)과 금속(Al6061)으로 이루어진 2층 층상재료에서는 섬광법(LFA)으로 열확산계수를 측정했을 때, 열흐름의 방향을 반대로 변화시켜도 열확산계수의 변화가 없었다. 그런데, 유전체(AlN-Polymer)와 금속(Al6061)의 2층 층상재료에서는 열흐름의 방향을 반대로 인가하였을 때 열확산계수는 17.5% 정도 다르게 나타났다. 유전체와 금속의 단면구조를 갖는 2층 층상재료에서, 금속에서 유전체 방향으로 측정한 열확산계수가 유전체에서 금속 방향으로 측정한 열확산계수에 비해 17.5% 작게 나타난 이유는, 금속내의 전자가 갖고 있던 에너지가 유전체 쪽으로 전달되기 위해서는 계면 주변에서 포논의 에너지 형태로 변환될 때 저항이 생기기 때문이다.

• 한국해양학회지
• /
• 제28권2호
• /
• pp.86-100
• /
• 1993

ADI(Alternating Direction Implicit) 유한차분법을 사용하여 3차원 경합 해수유 동 모델 BACHOM-3을 개발하였다. 본 모델을 장방형 내만에서 하나의 결점을 갖는 정상 파에 적용하여 해석해와 비교하였으며, 그 결과 해석해와 잘 일치하였다. 모델의 현지 적용성과 수영만의 해수유동을 조사하기 위해 모델을 수영만에 적용하여 대조기 평수 시 현지관측결과와 비교하였으며, 그 결과 현지 관측결과와 비교적 잘 일치하였다. 만 중앙부의 제 1층(수심 0∼2 m)과 제 2층(수심 2∼5 m)에서 조석잔차류는 시계방향으로 회전하는 순환류가 나타났으며, 또한 낙조류가 창조류보다 강하게 나타났다. 계산된 유속분포에 의하면, 표층과 저층 사이에 유속의 위상차가 나타나며, 표층으로 갈수록 위상의 지연이 나타났다. 그리고, 본 모델을 홍수시와 바람 효과를 고려한 흐름 장의 계산에도 적용하였다. 해양에서 육지로 바람이 불 때 표층에서는 풍향에 대응하는 유 속분포를 나타냈으나, 저층의 육지경계부근에서는 풍향과 반대방향의 흐름이 나타났 다.

• 한국가구학회지
• /
• 제28권3호
• /
• pp.248-258
• /
• 2017

A study was carried out to observe the 1% aqueous safranine solution flow speed in longitudinal and radial directions of softwood Thuja orientalis L., diffuse-porous wood Gmelina arborea Roxb., and ring-porous wood Phellodendron amurense Rupr., Longitudinal flow was considered from bottom to top while the radial flow was considered from bark to pith directions. In radial direction, ray cells and in longitudinal direction tracheids, vessel and wood fiber were considered for the measurement of liquid penetration speed at less than 12% moisture contents(MC). The variation of penetration speed for different species was observed and the reasons behind for this variation were explored. The highest radial penetration depth was found in ray parenchyma of T. orientalis but the lowest one was found in ray parenchyma of P. amurense. The average liquid penetration depth in longitudinal trachied of T. orientalis was found the highest among all the other cells. The penetration depth in fiber of G. arborea was found the lowest among the other longitudinal cells. It was found that cell dimension and also meniscus angle of safranine solution with cell walls were the prime factors for the variation of liquid flow speed in wood. Vessel was found to facilitate prime role in longitudinal penetration for hardwood species. The penetration depth in vessel of G. arborea was found highest among all vessels. Anatomical features like ray parenchyma cell length and diameter, end-wall pits number were found also responsible fluid flow differences. Initially liquid penetration speed was high and the nit gradually decreased in an uneven rate. Liquid flow was captured via video and the penetration depths in those cells were measured. It was found that even in presence of abundant rays in hardwood species, penetration depth of liquid in radial direction of softwood species was found high. Herein the ray length, lumen area, end wall pit diameter determined the radial permeability. On the other hand, vessel and fiber structure affected the longitudinal flow of liquids. Following a go-stop-go cycle, the penetration speed of a liquid decreased over time.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2007년도 추계학술대회
• /
• pp.71-76
• /
• 2007

Flow visualization of a droplet passing through a straight channel and a diverging channel has been carried out using micro-PIV. Diverging channel is frequently used in lab-on-a-chip and microfluidic devices, where flow pattern inside the droplet passing is quite different from that through a straight channel. In the present study, we visualized the droplet flow in three different regions. The first region is where the droplet has a wide contact area with the channel wall, the second region is characterized with a narrow contact area and the third region is where droplet is detached from the channel wall. Visualization results show that the internal flow inside the droplet passing through the straight channel moves in the opposite direction to the droplet velocity in the near wall exhibiting complex flow patterns. But in the diverging channel the internal flow inside the droplet moves in the same direction as the droplet velocity due to the shear induced by oil phase flow exhibiting rather simple flow pattern.

• 설비공학논문집
• /
• 제30권3호
• /
• pp.143-148
• /
• 2018

In this study the performance and humidity variation for 2 unit cells connected in series were experimentally measured. The relative flow direction of hydrogen and air was changed from parallel flow to counter flow. Internal humidity distribution was then measured by 5 embedded sensors on each channel. In all experimental conditions, the former unit cell showed a better performance and the gap is noted to be higher when counter flow is applied. The performance was noted to be higher at high humidification case in the parallel flow. However, in the counter flow, the difference of performance according to the humidification is negligible. Hydrogen and air are discharged from the PEMFC unsaturated with water vapor at parallel flow/low humidification condition, which explains lower performance of the PEMFC than other conditions. The humidities in hydrogen and air streams of counter flow were noted to increase rapidly even at low humidification condition and the consequential even hydration of membrane is the reason of higher performance.

• 한국수소및신에너지학회논문집
• /
• 제30권2호
• /
• pp.147-154
• /
• 2019

In this study, effects of flow types and size of molten carbonate fuel cells (MCFCs) were investigated using CFD simulation. In the simulation, the current collector of MCFCs were assumed to be an porous media. With the area of $0.09m^2$, the effect of flow types such as Co-flow, Counter-flow, Cross-flow were studied. After that the effect of the size and flow direction was studied. Among three-flow types, MCFCs with co-flow type shows more uniform distribution and current density distribution.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.109-116
• /
• 2004

Through analysing the influence of steam flow direction on the liquid formation and motion behavior in the condenser shell side, the physical model for existing numerical simulation program of condenser is improved by introducing the correlations for flow resistance and condensation heat exchange coefficient in which the influences of steam flow direction are considered according to the available experimental data. Thus a more suitable and general condenser simulation approach is presented and a new condenser calculation program is developed. With the experimental data of a pannier- arrangement experimental condenser, the adaptability of the new condenser simulation approach is verified. General characteristics of this type of condenser are also revealed.

• 한국분무공학회지
• /
• 제20권2호
• /
• pp.70-75
• /
• 2015

Swirl flow in the gun type burner has an impact on the stabilization of the flame, improvement of the combustion efficiency. The swirl flow is created by the spinner which is inside the airtube that guide the combustion air. Gun type burner has generally the inner devices composed electronic spark plug, injection nozzle, combustion device adaptor, and spinner. These inner components change the air flow behavior passing through airtube. So, this study conducted the measurement using by hot-wire anemometer and analyzed effect of the swirl number of spinner on the exhaust air of gun type burner. Turbulence characteristics come up in this study was mean velocity, turbulence intensity, kinetic energy, shear stress and flattness factor of the air flow with the change of the distance of axial direction and tangential direction from the exit of the airtube.