• 대한치과기공학회지
• /
• 제43권1호
• /
• pp.13-18
• /
• 2021

Purpose: This study aimed to compare the flexural properties and perform the Weibull analysis of photo-curing three-dimensional (3D) printing resin. Methods: Photo-curing temporary resin (3D polymer) was used as a printing resin. Specimens (65 × 10 × 3.3 ㎣) were prepared following the ISO 20975-1 guidelines and according to the different printing orientations using a digital light processing 3D printer (D2 120; Dentium). The flexural strength (FS), flexural modulus, and work of fracture (WOF) were measured using a universal testing machine (Instron 3344; Instron) at a crosshead speed of 5 mm/min. Results: In this study, the 0° orientation exhibited higher FS and WOF than the 45° orientation. Significant differences were found among the printing orientations (p<0.05). Specimens printed at the 0° orientation were the most accurate. In the Weibull analysis, 0° showed the greatest Weibull modulus (m), which represents a higher reliability. Conclusion: 3D printing should be selected and used by considering flexural properties, size accuracy, and reliability.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권2호
• /
• pp.202-208
• /
• 1998

To investigae the effect of anchorage type of carbon fiber sheet (CFS) on flexural behavior of RC beams, the loading test of RC beams reinforced with CFS was conducted in variable of anchorage Type such as bolting anchorage and U type anchorage using CFS. This study can be summarized as follows ; It is confirmed experimentally that the bolting anchorage and U type anchorage with CFS is very effective to delay the bond failure and prevent the peeling of CFS. Also, the anchorage type applied with this study is very effective to improve the ductility compared with the improving of maximum flexural strength of RC beams. It is believed that the anchorage type used this study must secure the ductile capacity of above 3 for the flexural strengthening of RC beams. In the future, it is required to obtain the data about anchorage type of CFS for utilization of field work as well as investigate the ductile capacity of conventional study of anchorage type

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1985년도 학술발표회 논문집
• /
• pp.27-30
• /
• 1985

• 대한치과보철학회지
• /
• 제43권3호
• /
• pp.293-305
• /
• 2005

Statement of problems. Conventional feldspathic porcelain is used extensively as a restorative material and it is subjected to grinding and polishing during fabrication and delivery procedures. There is still considerable controversy concerning the best methods to achieve the strongest porcelain restorations after such adjustments. Purpose. The objective of this study was to investigate the effects of (1) overglazing, (2) selfglazing, and (3) fine polishing on the flexural strength and fracture toughness of feldspathic dental porcelain. Material and method. Ninety porcelain disks were prepared for flexural strength test and sixty porcelain disks were fabricated for fracture toughness test. Specimens were divided into three groups for each test as follows: 1) overglazed 2) self-glazed 3) polished. The flexural strength of feldspathic porcelains was determined by ring-on-ring biaxial flexural strength test. The fracture toughness values of three experimental groups were obtained by indentation fracture toughness test. Results. The flexural strength of overglazed group was significantly higher than that of selfglazed and polished group (P<0.05), while the difference between self-glazed and polished group was not significant (P>0.05). The fracture toughness values of overglazed and polished group were significantly higher than that of self-glazed group (P<0.05), while the difference between overglazed and polished group was not significant (P>0.05). Conclusions. This results supported the use of polishing as an alternative to glazing metal ceramic restorations, as it was not detrimental in flexural strength and fracture toughness. But, under the conditions of this study, overglazing was the ideal surface finishing method of feldspathic dental porcelain.

• 대한치과보철학회지
• /
• 제44권3호
• /
• pp.333-342
• /
• 2006

Statement of problem. Although many studies have been carried out to investigate the correlation between the degree of conversion and the flexural strength of composite resins, there is minimal information in the literature attempting to compare degree of conversion, flexural strength and their correlation between restorative composite resins and flowable composite resins. Purpose. The purposes of this study were to measure the degree of conversion and flexural strength of composite resins with different rheological behavior and to correlate the two properties. Materials and methods. Four restorative (Vit-1-escence, Z-250, Tetric ceram, Esthet-X) and four flowable (Aeliteflo, Admiraflow, Permaflo, Revolution) light-curing composite resins were investigated. The degree of conversion(DC) was analyzed with Fourier transfer infra-red spectroscopy(FTIR) spectrum by a potassium bromide(KBr) pellet transmission method. The spectrum of the unpolymerized specimen had been measured before the specimen was irradiated for 60s with a visible light curing unit. The Poiymerized specimen was scanned for its in spectrum. The flexural strength(FS) was measured with 3-point bending test according to ISO 4049 after storage in water at $37^{\circ}C$ for 24 hours. The data were statistically analyzed by an independent sample t-test and one-way ANOVA at the significance level of 0.05. The dependence of flexural strength on the degree of conversion was also analyzed by regression analysis. Results. Mean DC and FS values ranged from 43% to 61% and from 84.7MPa to 156.7MPa respectively. DC values of the flowable composite resins were significantly higher than those of restorative composite resins (P < 0.05). The FS values of restorative composite resins were greater than those of flowable composite resins. No statistically significant correlation was observed between the DC and the FS tested in any of the composites. The dependence of FS on DC in restorative or flowable composite resins was not significant. Conclusion. It can be concluded that radical polymerization of the organic matrix is not a major factor in determining flexural strength of the commercially available composite resins.

• 한국농공학회지
• /
• 제29권4호
• /
• pp.132-141
• /
• 1987

The objective of the study was to obtain the compressive the tensile and the fleniril strengthes, thermal resistance, chemical resistance and fire resistance of the reclaimed plastic corcrete in order to investigate the feasibility as a new construction material This reclaimed plastic concrete is a compositive material which is composed of sand and blend of 50% of LDPE(Low density polyethylene) and 50% of HDPE (High density polyethylene) which are inexpensive and easy to reclaim. The results obtained in the study are summarized as follows: 1. As the binder content ranging from 20 to 40 % increase, the compresie, the splitting tensile and the flexural strengthes were increased. The compressive strenzth of the specimen tested was the highest and flexural strength the next and tensile strength the lowest 2. The compressive, the tensile and flexural strengthes of specimens made of fine sand were higher than those of coarse sand. The compressive, the tensile and the flexural strengthes of specimens made of high pressure molding were higher than those of low pressure molding. 3.In comparison with different additives, the specimens with carbon black was excellent and B. H. T. good and ferric oxide poor for thermal resistance. 4. In relationship between the flexural strength with varying temperature from -23$^{\circ}C$ to 80$^{\circ}C$. The flexural strengthes were decreared as temperature increased at 25 %, 30 % and 35 % of binder contents, respectively. Especially at 60$^{\circ}C$, the flexural strength was significantly decreased. 5. The decrement of flexural strengthes and the weight losses after 7 days immersion in acid or alkali solutions were not significant. 6. Fire resistance of the reclaimed plastic concrete was not significantly influenced by the contents of sand. However, the fire resistance of the reclaimed plastic concrete was depend upon melting and ignition properties of the binder itself. Therefore. a proper selection of the binder and the fire retardant are recommended in arder to improve fire resistance of the reclaimed plastic concrete.

• 한국건설순환자원학회논문집
• /
• 제7권2호
• /
• pp.158-165
• /
• 2019

이 연구의 목적은 알칼리활성 슬래그 기반 섬유보강 복합재료를 보 부재의 재료로 활용하였을 때 휨거동을 해석적으로 분석하는 것이다. 7% 이상의 초고연성이 나타날 수 있는 알칼리활성 슬래그 기반 섬유보강 복합재료를 제조하기 위하여 재료 및 배합을 선정하였고, 재료의 압축강도와 인장성능을 평가하였다. 복합재료는 압축강도 32.7MPa, 인장강도 8.43MPa, 인장변형성능 7.52%를 나타내었다. 초고연성 복합재료로 구성된 보의 휨거동을 분석하기 위하여 4가지 단면에 대하여 비선형 단면 층상화 방법을 사용하여 해석을 수행하였다. 해석결과 초고연성 복합재료로 부분적으로 보강된 경우 8.0%, 콘크리트가 복합재료로 전부 치환되어 전체 보강된 경우 24.7%의 휨강도 증진효과가 있는 것으로 나타났다. 휨강도 증진 효과가 크지 않은 이유는 인장 연단의 변형률이 최대 1.38%로 초고연성 복합재료의 인장변형성능의 18.4%밖에 되지 않기 때문인 것으로 나타났다.

• 구강회복응용과학지
• /
• 제37권1호
• /
• pp.16-22
• /
• 2021

목적: 표면연마와 제작방법이 임시 수복용 레진의 굽힘강도에 미치는 영향을 분석하고자 한다. 연구 재료 및 방법: 4가지 제작방법을 이용하여 각각 30개의 임시 수복용 레진 시편을 제작하였고, 기계적 연마로 표면연마를 시행한 그룹과 연마를 시행하지 않은 2개의 그룹으로 나누었다. 시편은 37℃ 항온기에 24시간 보관 후 만능시험기(Universal testing machine)을 이용하여 3점 굽힘강도를 측정하였다. 통계분석은 Two-way ANOVA와 Tukey's HSD test, Paired t-test를 이용하여 분석하였다. 결과: 표면연마 여부와 관계없이 CAD/CAM milling으로 제작한 시편이 가장 높은 굽힘강도를 나타냈고, SLA 3D printing, DLP 3D printing, Conventional method 순으로 높은 굽힘강도를 나타냈다. 결론: 표면연마는 임시 수복용 레진의 굽힘강도에 유의한 영향을 끼치지 못했지만(P > 0.05), 제작방법에 의해서는 굽힘강도의 유의한 차이가 나타났다(P < 0.05).

• 한국건축시공학회지
• /
• 제24권1호
• /
• pp.23-34
• /
• 2024

본 연구의 목적은 RC 구조물의 균열 보수용 폴리머 시멘트 복합체의 휨접착성능을 평가하기 위함이다. 시멘트 모르타르에 다양한 크기의 균열을 만들어 PCCs를 충전한 후, 소정의 양생을 거쳐 휨접착강도와 휨강도 개선 정도를 파악하였다. 연구결과, 균열보수용 PCCs의 휨접착강도는 시멘트의 종류, 폴리머 종류 및 폴리머 결합재비에 따라 영향을 받으며 실리카퓸을 혼입한 초조강시멘트를 사용한 경우가 보통시멘트를 사용한 경우에 비해 최대 19.0%의 휨접착강도 개선효과가 나타났다. PCCs로 충전된 시멘트 모르타르의 휨강도 개선 정도는 균열폭의 영향보다는 균열깊이에 따라 큰 차이를 보였으며 균열에 충전된 PCCs가 단순히 보수재료로서 기능뿐만 아니라 어느 정도 휨강도를 개선시키는 보강재료로서도 역할을 하였다. 본 연구결과, 초조강시멘트, 3종류의 폴리머 디스퍼전과 실리카퓸, 60%~80%의 높은 폴리머 결합재비로 제작한 PCCs가 균열을 충전하는 보수재료로서 현장에서 충분히 사용될 수 있을 것이다.

• 콘크리트학회논문집
• /
• 제26권4호
• /
• pp.483-489
• /
• 2014

이 연구에서는 ASTM C 1609을 따라서 비정질 강섬유보강콘크리트의 휨실험을 수행하였고, 이를 바탕으로 휨성능을 평가하였다. 비정질 강섬유는 기존의 일반 강섬유와 달리 얇은 두께, 거친 표면의 특성을 가지고 있다. 주요한 실험변수는 섬유 종류(비정질 강섬유, 일반 강섬유), 섬유 혼입률(0.25, 0.50, 0.75%) 그리고 콘크리트 압축강도(27, 50 MPa)이다. 실험 결과에 근거하여 비정질 강섬유와 일반 강섬유보강콘크리트의 휨강도와 휨인성을 분석하였고, 그 결과 일반 강섬유보강콘크리트의 경우 주로 휨인성이 증가하였으나 비정질 강섬유보강콘크리트의 경우 휨강도와 인성을 모두 증가하는 것으로 나타났다.