• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.196-200
• /
• 2005

In this work, we investigated simple Aㅣ/TCO/a-Si:H(n)/c-Si(p)/Al hetero-junction solar cells prepared by low temperature processes, unlike conventional thermal diffused c-Si solar cells. a-Si:H/c-Si hetero-junction solar cells are processed by low temperature deposition of n-type hydrogenated amorphous silicon (a-Si:H) films by plasma-enhanced chemical vapor deposition on textured and flat p-type silicon substrate. A detailed investigation was carried out to acquire optimization and compatibility of amorphous layer, TCO (ZnO:Al) layer depositions by changing the plasma process parameters. As front TCO and back contact, ZnO:Al and AI were deposited by rf magnetron sputtering and e-beam evaporation, respectively. The photovoltaic conversion efficiency under AMI.5 and the quantum efficiency on $1cm^2$ sample have been reported. An efficiency of $12.5\%$ is achieved on hetero-structure solar cells based on p-type crystalline silicon.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.6
• /
• pp.620-624
• /
• 1992

The analytical performance of glow discharge mass spectrometer (GD-MS), using a flat type ion source is discussed. The efficiency of ion extraction was maximized at the distance between anode and cathode of 6 mm. At the operation condition of 4 mA, -1000 volt, and 1 mbar for the source, the optimum voltages for sampler and skimmer were40 volt and -280 volt, respectively. The intensities of Cu, Zn, and Mn were increased as a function of square root of current approximately. Korea standard reference materials (KSRM) were tested for an application study. The detection limits of most elements were obtained in the range of several ppm at the optimized operating condition. The peaks of aluminum and chromium were interfered by those of residual gases. The depth profile of nickel coated copper specimens (3, 5, 10 ${\mu}m$ thickness) were obtained by plotting time versus intensities of Ni and Cr after checking the thickness of nickel coated using a scanning electron microscope (SEM). At this moment, the sputtering rate of 0.2 ${\mu}m/min$ at the optimum operating condition was determined from the slope of the plot of time to the coating thickness. The roughness spectra of specimen's crater after 16 min, discharge were obtained using a Talysuf5m-120 roughness tester as well.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.574-578
• /
• 2006

Tidal amplification by construction of the sea-dike and sea-walls had been detected not only near Mokpo Harbor but also at Chungkye Bay which is connected with Mokpo Harbor by a narrow channel. This brings about increase of tidal flat area and in particular increase of surge-wave combined runup during storms. The purpose of this study is to examine an efficient operational model that can be used by civil defense agencies for real-time prediction and fast warnings on wind waves and storm surges. Instead of using commercialized wave models such as WAM, SWAN, the wind waves are simulated by using a new concept of wavelength modulation to enhance broader application of the hyperbolic wave model of the mild-slope equation type. Furthermore, The predicting system is composed of easy and economical tools for inputting depth data of complex bathymetry and enormous tidal flats such as Mokpo coastal zone. The method is applied to Chungkye Bay, and possible inundation features at Mokpo Harbor are analyzed.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.947-949
• /
• 2004

철심형 영구 자석 선형 전기기기에서 디텐트력은 구조상 피할 수 없는 기기 특성이다. 본 연구에서와 같이 정격 외부 입력이 작은 경우, 디텐트력은 기기의 성능에 크게 영향을 미칠 수 있으며, 이를 저감할 수 있는 설계법이 필수적이다. 본 논문에서는 1kw급 왕복 구동 평판형 선형 영구자석 발전기의 치의 구조에 따른 역기전력과 디텐트력의 관계를 해석 하였다. 치의 구조에 따른 디텐트력의 변화를 해석적 방법을 통해 예측하고, 이를 기기 설계에 적용, 유한요소법을 이용해 실제 모델을 해석하였다. 치 구조의 변화는 디텐트력 외에 역기전력에도 영향을 주게 되는데 기기의 목표 성능을 만족할 수 있도록 설계안의 적절한 선택이 필요하다.

• The International Journal of Costume Culture
• /
• v.2 no.1
• /
• pp.43-53
• /
• 1999

The research analyzs characteristics of body types for the Chineses women based on the different life style and to compare the differences of body type with Korean women. The measurement had took in Beijing and Seoul in 1999. As a result of comparing Chinese and Korean women'body measurements, it was found that Chinese women are shorter and obser than Korean women. Besides, chinese arms and upper body are shorter, and their body is thicker compared with their relatively flat chest. After all, Cheinese women'chests are more voluminous, while their shoulders are drooped more, although their shoulder size is almost as same as Korean women'. By used factor analysis, 8 factors were extracted from body measurements : body obesity, vertical body size, ankle and knee sizes, head size, front upper body length, shoulder size, form and size of neck and upper chest, drooping of shoulders, and size of hip. It was found that Chinese college women are obser with larger vertical body length and front upper body length. And their shoulders are more drooped with larger hip. But two nations'female students did not show any differences in the sizes of ankles, knees, head and shoulders.

• Analytical Science and Technology
• /
• v.5 no.2
• /
• pp.169-176
• /
• 1992

Analytical detection limits and Relative Ion Yield (RIY) by a jet type ion source glow discharge mass spectrometer(GD/MS) have been measured. With a jet type ion source, the sample loss rate for a Cu sample is 0.23 mg/min with 0.1 L/min gas flow rate and 0.11 mg/min with no gas flow rate. However, the ion intensity of Cu does not change significantly with thee variation of the gas flow rate. The RIY values obtained from the calibration curves of the six copper based standards were between 0.57 of Fe and 3.5 of Cr. The detection limits of most elements were in the range of 0.9 and 2.0 ppm when the glow discharge was operated at 4 mA, 1000V.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.6
• /
• pp.727-735
• /
• 2005

Statement of problem. Platform switching in implant prosthesis has been used for esthetic and biological purpose. But there are few reports for this concept. Purpose. The purpose of this study is evaluation of platform switching in wide implant by three dimensional finite element analysis. Materials and Methods. The single implant and prosthesis was modeled in accordance with the geometric designs for Osstem implant system. Three-dimensional finite element models were developed for (1) a wide diameter 3i type titanium implant 5 mm in diameter, 13 mm in length with wide cemented abutment, titanium alloy abutment screw, and prosthesis (2) a wide diameter 3i type titanium implant 5 mm in diameter, 13 mm in length with regular cemented abutment, titanium alloy abutment screw and prosthesis(platform switching) was made for finite element analysis. The abutment screws were subjected to a tightening torque of 30 Ncm. The amount of preload was hypothesized to 650N, and round and flat type prostheses were loaded to 200 N. Four loading offset point (0, 2, 4, 6 mm from the center of the implants) were evaluated. Models were processed by the software programs HyperMesh and ANSA. The PAM-CRASH 2G simulation software was used for analysis of stress. The PAM-VIEW and HyperView were used for post processing. Results. The results from experiment were as follows; 1. von Mises stress value is increased in order of bone, abutment, implant and abutment screw. 2. von Mises stress of abutment screw is lower when platform switching. 3. von Mises stress of implant is lower when platform switching until loading offset 4 mm. 4. von Mises stress of abutment is similar between each other. 5. von Mises stress of bone is slightly higher when platform switching. Conclusion. The von Mises stress pattern of implant components is favor when platform switch ing but slightly higher in bone stress distribution than use of wide abutment. The research about stress distribution is essential for investigation of the cortical bone loss.

• Environmental Analysis Health and Toxicology
• /
• v.25 no.2
• /
• pp.121-129
• /
• 2010

This study was carried out to investigate whether asian yellow sand dust (AS) has promoting effects of allergen-related airway inflammation and airway hyperresponsiveness, because the number of patient with allergic asthma and atopy, and with chronic bronchial inflammation and pneumonia have increased steadily in the cities of Korea. The appearance of AS collected was all round and flat, and the diameter was mostly below about 5 ${\mu}m$. When mice were treated with AS suspension by intratracheal instillation combined with ovalalbumin(OVA) sensitization chronically, the level of serum L-lactate dehydrogenase (LDH), IgE and histamine, and respiratory resistance was increased. Intratracheal instillation of AS and OVA also enhanced infiltration of eosinophils in the bronchoalveolar lavage fluid (BALF), IgE and eotaxin expression, and T helper type 2 cell derived cytokines of interleukin (IL)-4, IL-13 and IL-5 as major contributors to allergy and asthma. These results indicate that AS elevates allergen-related airway inflammation and airway hyperresponsiveness in mice and may play an important role in the aggravation of respiratory diseases in Korea.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.4
• /
• pp.145-152
• /
• 2016

For a general office building having a center core, the distinction between the outer wall and the compartment should be clear, and it should be set at a stack effect pressure distribution acting on the respective compartment by a relative area ratio of the respective leak compartment. In the case of office buildings with an independent core for core there, some blocks of shares and exterior pressure distribution in buildings and office buildings typically have different characteristics. Therefore, if the stack effect reduction measures, designed on the basis of a general office building are applied to a stand-alone building, the core of the building should reflect the unique pressure distribution characteristics. This study, performed as part of the object corresponding to the flat plan of the building in the diversification trend, analyzed the stack effect that actually occurs in an office building having the properties intended for stand-core construction, and thus on the basis of and tested by the method of using a conventional stack effect reduction measures. Reviewed in the study, an independent cored office building that does not have the air flow path through the specific space with respect to the center core type office building has a feature, and the variation in characteristics of the pressure distribution inside the building according to this air flow path stack effect was reduced by a variety of measures that should be applied to determine the application.

• Journal of Fashion Business
• /
• v.5 no.2
• /
• pp.129-147
• /
• 2001

The purpose of this study is to survey and analyze domestic fashion education institution's program on apparel prototype and thereupon, address the problems and find their solutions, and thereby, provide for some basic data useful to improve the basic patterns of apparel and ultimately, help reinforce the professional and practical apparel design education. The results of this study can be summarized as follows; 1. 85.1% of the subjects finished graduate or higher courses. Almost all of the college and junior college teachers finished graduate or higher courses, while only 31.6% of those teaching at technical institutes finished graduate or higher courses. Such a finding suggests that colleges tend to employ their faculty members based on their academic background but that technical institutes value the practical ability of their faculty more. 2. As a result of surveying the types of basic patterns used by teachers, it was found that 72.3% of them were using two or more patterns. The basic pattern preferred most by our teachers was Japanese culture institute's type (71.3%), followed by the US FIT type (24.5%), Lim Won-Ja's type (22.3%), French ESMOD type (17.0%). 96.3% of our apparel design students were making their basic patterns as instructed by their teachers. 3. 67.0% of our students were using their conceived sizes for production of their basic patterns, 14.9% were referring to the ready-made sizes, 8.5% were relying on their teachers' individual experiences, and 9.6% were using their own cord sizes. In order to survey the difference between teachers' sizes (ready-made sizes or individual experienced ones) and business sizes used, the basic body measurements used for ready-made apparels were surveyed to be compared with the national standard body sizes set in 1997 for women aged between 18 and 24. As a result, it was found that the ready-made sizes used for apparel production prototypes than teachers' ones were nearer the national standard sizes. Such a finding suggests that it may well be necessary for teachers to be more connected with the apparel businesses and thereby, teach their students in a more realistic way with correct information. 4. 83.0% of the subject teachers were tacking their basic patterns to be well fitting, and 76.9% of these teachers were tacking the patterns in reference with students' individual body sizes. In all, 97.4% of the subject teachers were guiding the tacking process, which suggests that the flat patternmaking is taught primarily for customized apparels. As a result of comparing the fitness of basic patterns with those of each body part, it was found that teachers were most dissatisfied with the fitness of shoulders and arm hole depth. Therefore, it will be necessary to reclassify the body types or find other drawing techniques to improve the fitness of such body parts. Nevertheless, teachers were willing much (4.18) to develop their own educational basic patterns for themselves. Lastly, it is hoped that this study will be followed up by future studies on educational prototypes covering diverse body shapes and those on practical implementations of those prototypes for students.