• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.2 s.43
• /
• pp.35-40
• /
• 2007

The pull strength and fracture mechanism were investigated to evaluate the reliability and compatibility of Sn-8Zn-3Bi joints, the solder paste on lead and lead-free plating under thermal shock conditions. At the Sn-8Zn-3Bi solder joint, no crack initiation was observed during thermal shock test. After 1000 cycles, the strength of the solder joint decreased not sharply but reduced gradually compared with initial conditions. The decrement of strength was affected by ${\gamma}-Cu_5Zn_8$ IMC growth which caused the IMC fracture on the fracture surface and a change in fracture mode and initial crack point. Clearly, the Sn-8Zn-3Bi solder shows good reliability properties and compatibility with lead-free plated Cu LF under thermal shock temperatures between 248K and 423K.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.5 no.1
• /
• pp.39-51
• /
• 1999

Background and Purpose. Objective measurements of hamstring muscle length are needed to quantify baseline limitations and to document the effectiveness of therapeutic interventions. Several indirect clinical tests for measuring hamstring muscle length are available, but influence of their test procedure is not well documented. The purpose of this study were 1) to describe hamstring muscle length as reflected by use of six tests(active straight leg raising(ASLR), passive straight leg raising(PSLR), passive straight leg raising with the lower back flat(PSLRB), active knee extension(AKE), passive knee extension(PKE), hip joint angle(HJA). 2) to examine the correlation among the tests. Subjects, Sixty subjects(30 men. 30 women) ranging in age from 18 to 25 years(mean 20.2 years) and with no limitation hamstring flexibility and no neurological and orthopedical problems. Methods. All subjects performed six tests. A inclinometer was used to determine the end point of range of motion. HJA was measured using an inclinometer placed over the sacrum. PSLRB were tested PSLR with the low back flat and the opposite thigh slightly flexed and support on pillows. Results, A mean ASLR value of 85.9 degrees, PSLR value of 99.9 degrees, PSLRB value of 109.8 degrees, AKE value of 77.2 degrees PKE value of 83.1 degrees and HJA value of 73.0 degrees were obtained for all subjects. A dependent t-test showed significant difference between the angles of ASLR and PSLR(p<0.001). There was a significant difference between the angles of PSLR and PSLRB(p<0.001). There was a significant difference between the angles of AKE and PKE(p<0.001). The highest correlation was between PSLR and PSLRB(r=0.915, p<0.001). All SLR tests were significants related(p<0.001), as well as AKE and PKE(p<0.001). The lowest correlation was between PKE and HJA(r=0.171. p>0.05). Conclusion and Discussion. The results indicated that the hip flexion angles for ASLR, PSLR and PSLRB were a difference, and the knee extension angles for AKE and PKE were a difference.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1A
• /
• pp.24-33
• /
• 2007

In this paper, two different dynamic cell coordination strategies for frequency flat and selective fading are proposed for efficient subcarrier allocation in the joint consideration of adaptive modulation and variable frequency reuse in the channel-aware OFDMA downlink multicellular environment. Compared to a conventional OFDMA system without cell coordination, where system throughput may become degraded due to the persistent interference from other cells, the proposed system dynamically allows RNC to apply different reuse factors on each subchannel and scheduling in consideration of channel and interference conditions of individual users so as to increase the system throughput and guarantee QoS of each user. In a frequency flat fading, the dynamic scheme with the proposed scheduling achieves on average three times larger throughput than the conventional dynamic scheme [8]. In a selective fading channel, the proposed schemes showed 2.6 times as large throughput as that of a single reuse factor of one for all subchannels.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.2
• /
• pp.34-39
• /
• 2003

Recent deepwater offshore structures in the Gulf of Mexico utilize butt welded tubular joints. Application of a welded tubular joint includes tendons, production risers, and steel catenary risers. Fatigue life assessment of these joints becomes more critical, as the structures to which they are attached are allowed to undergo cyclic and sometimes large displacements around an anchored position. Estimation of the fatigue behavior of these tubular members in the design stage is generally condrcted by using S-N curves, as specified in the codeds and standards. Applying the stress concentration factor of the welded structure to the S-N approach often results in a very conservative assessment, because the stress field acting on the tubular has a non-uniform distribution through the thickness. Fatigue life analysis using fracture mechanics has been applied in the design of the catenary risers. This technology enables the engineer to establish proper requirements on weld quality and inspection acceptance criteria to assure satisfactory structural integrity during its design life. It also provides guidance on proper design curves and a methodology for accounting for the effects of non-uniform stress distribution through the wall thickness. Still, there is inconsistency when designing tubular joints using a conventional S-N approach and when specifying weld flaw acceptance criteria using fracture mechanics approach. This study developed fatigue curves that are consistent with both the S-N approach and the fracture mechanics approach. Accounting for non-uniform stress distribution and threshold stress intensity factor were key parameters in relating both approaches. A series of S-N curves, generated from the fracture mechanics approach, were compared to the existing S-N curves. For flat plate butt joint, the S-N curve generated from fracture mechanics matches with the IIW class 100 curve when initial crack depth was 0.5 mm (0.02 ). The new curves for tubular joint agree very well with the experimental results. The comparison also indicated the degree of conservatism built into the API X design curve.

• Korean Journal of Agricultural Science
• /
• v.32 no.2
• /
• pp.107-126
• /
• 2005

The most limited production resource in Korea is land. During the period from 1995 to 2002, annual farm land area of 17,600ha have been converted to urban and industrial land. The self-sufficiency rate of rice, Korean staple food, is expected to be decreased from 97.5% in 2003 to 60-70% in 2020. Under such conditions, this study is aimed at first identifying multi-functional benefits of the reclamation projects such as agricultural production, industrial water supply, urban land supply, transportation effects, sightseeing effects and environmental values with and without the projects. To carry out the objectives, three existing tideland reclamation projects such as Daeho, Kumgang and Yongsangang irrigation project stage II were evaluated and Saemangeum tideland reclamation project which was jointly revaluated by environmental NGO and Govn't appointed specialists in 2000 was reviewed. According to this study results, tide land reclamation projects were showed financially and economically feasible and environmentally sustainable. The joint cost like estuary dam should be allocated based on the multi-functional benefits of the projects. To allocate the joint cost, legal and institutional improvement should adapt the joint cost allocation method as the specific cost-remaining benefit method. Korea has more than 402,000 ha of tidal flat of which 76,396ha have been reclaimed in 2003. To meet food security and to cope with shortage of land, phil-environmental reclamation projects should be continuously implemented and necessary tidal flats for protecting environmental ecosystem should be remained according to the detail survey results of reclaimable resources.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.69-74
• /
• 2003

Recent deepwater offshore structures in the Gulf of Mexico utilize butt welded tubular joints. Application of a welded tubular joint includes tendons, production risers, and steel catenary risers. Fatigue life assessment of these joints becomes more critical, as the structures to which they are attached are allowed to undergo cyclic and sometimes large displacements around an anchored position. Estimation of the fatigue behavior of these tubular members in the design stage is generally conducted by using S-N curves, as specified in the codes and standards. Applying the stress concentration factor of the welded structure to the S-N approach often results in a very conservative assessment, because the stress field acting on the tubular has a non-uniform distribution through the thickness. Fatigue life analysis using fracture mechanics has been applied in the design of the catenary risers. This technology enables the engineer to establish proper requirements on weld quality and inspection acceptance criteria to assure satisfactory structural integrity during its design life. It also provides guidance on proper design curves and a methodology for accounting for the effects of non-uniform stress distribution through the wall thickness. Still, there is inconsistency when designing tubular joints using a conventional S-N approach and when specifying weld flaw acceptance criteria using fracture mechanics approach. This study developed fatigue curves that are consistent with both the S-N approach and the fracture mechanics approach. Accounting for non-uniform stress distribution and threshold stress intensity factor were key parameters in relating both approaches. A series of S-N curves, generated from the fracture mechanics approach, were compared to the existing S-N curves. For flat plate butt joint, the S-N curve generated from fracture mechanics matches with the IIW class 100 curve when initial crack depth was 0.5 mm (0.02). The new curves for tubular joint agree very well with the experimental results. The comparison also indicated the degree of conservatism built into the API X design curve.

• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.152-159
• /
• 2007

When the electronics are tested with thermal shock for Pb-free solder joint reliability, there are temperature conditions with use environment but number of cycles for test don't clearly exist. To obtain the long term reliability data, electronic companies have spent the cost and times. Therefore this studies show the test method and number of thermal shock cycles for evaluating the solder joint reliability of electronic components and also research bonding strength variation with formation and growth of intermetallic compounds (IMC). SMD (surface mount device) 3216 chip resistor and 44 pin QFP (quad flat package) was utilized for experiments and each components were soldered with Sn-40Pb and Sn-3.0 Ag-0.5 Cu solder on the FR-4 PCB(printed circuit board) using by reflow soldering process. To reliability evaluation, thermal shock test was conducted between $-40^{\circ}C\;and\;+125^{\circ}C$ for 2,000 cycles, 10 minute dwell time, respectively. Also we analyzed the IMCs of solder joint using by SEM and EDX. To compare with bonding strength, resistor and QFP were tested shear strength and $45^{\circ}$ lead pull strength, respectively. From these results, optimized number of cycles was proposed with variation of bonding strength under thermal shock.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.1
• /
• pp.65-72
• /
• 2016

In this study, a fully active transfemoral prothesis with a knee joint is designed considering stair walking conditions. Since the torque at the knee joint required for stair walking condition is relative high compared with the one in normal walking condition, the proposed design has high torque generating mechanism. Moreover, the transfemoral prothesis is designed in compact size to reduce its weight, which is related to comfortable fit and fatigue of patients. Flat type BLDC motor is used for simple and compact structure and various components are used to generate required torque with target working angle and speed. The weight reduction of structure is carried out using optimization method after the initial design process is complete. The optimization is conducted under the load conditions of stair walking. The optimized design is validated via finite element analysis and experiments. As a result, the weight is reduced using topology and shape optimization but maintaining the safety of structure. Also the space efficiency is improved due to its compact size.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.12
• /
• pp.1233-1240
• /
• 2010

In the flat panel display and semiconductor industries, the visual alignment system is considered as a core technology which determines the productivity of a manufacturing line. It consists of the vision system to extract the centroids of alignment marks and the stage control system to compensate the alignment error. In this paper, we develop a Kalman filter algorithm to estimate the alignment mark postures and propose a coarse-fine alignment control method which utilizes both original fine images and reduced coarse ones in the visual feedback. The error compensation trajectory for the distributed joint servos of the alignment stage is generated in terms of the inverse kinematic solution for the misalignment in task space. In constructing the estimation algorithm, the equation of motion for the alignment marks is given by using the forward kinematics of alignment stage. Secondly, the measurements for the alignment mark centroids are obtained from the reduced images by applying the geometric template matching. As a result, the proposed Kalman filter based coarse-fine alignment control method enables a considerable reduction of alignment time.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10C
• /
• pp.929-936
• /
• 2009

In this paper, we consider designing a multi-input multi-output (MIMO) overlay system for fixed MIMO wireless link, where a frequency flat narrowband channel is shared by multiple transmitter and receiver pairs. Assuming the perfect knowledge of the second-order statistics of the received legacy signals and the composite channels from the overlay transmitter to the legacy receivers, the jointly optimal linear precoder and decoder matrices of the MIMO overlay system is derived to minimize the total mean squared error (MSE) of the data symbol vector, subject to total average transmission power and zero interference induced to legacy MIMO systems already existing in the frequency band of interest. Furthermore, the necessary and sufficient condition for the existence of the optimal solution is also derived.