• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.54-65
• /
• 1997

To quantify the LII signals from soot particle of flames in diesel engine cylinder, a new method has been proposed for correcting LII signal attenuated by soot particles between the measuring point and the detector. It has been verified by an experiment on a laminar jet ethylene-air diffusion flame. Being proportional to the attenuation, the ratio of LII signal at two different detection wavelengths can be used to correct the measured LIIsignal and obtain the unattenuated LII signal, from which the soot volume fraction in the flame can be estimated. Both the 1064-nm and frequency-doubled 532-nm beams from the Nd : YAG laser are used. Single-shot, one-dimensional(1-D) line images are recorded on the intensified CCD camera, with the rectangular-profile laser beam using 1-mm-diameter pinhole. Two broadband optical interference filters having the center wavelengths of 647 nm and 400 nm respectively and a bandwidth of 10 nm are used. This two-wavelength correction has been applied to the ethylene-air coannular laminar diffusion flame, previously studied on soot formation by the laser extinction method in this laboratory. The results by the LII measurement technique and the conventional laser extinction method at the height of 40 nm above the jet exit agreed well with each other except around outside of the peaks of soot concentration, where the soot concentration was relatively high and resulting attenuation of the LII signal was large. The radial profile shape of soot concentration was not changed a lot, but the absolute value of the soot volume fraction around outside edge changed from 4ppm to 6.5 ppm at r=2.8mm after correction. This means that the attenuation of LII signal was approximately 40% at this point, which is higher than the average attenuation rate of this flame, 10~15%.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.146-153
• /
• 2011

American NREL (National Renewable Energy Laboratory) reported that BDF20 could reduce PM, CO, SOx, and cancerogenic matters by 13.6%, 9.3%, 17.6%, and 13% respectively, compared to diesel fuel. BDF20 has been being tested on garbage trucks and official vehicles at Seoul City, which is positive on air environment, but negative on combustion by higher viscosity in winter season. This study investigated the combustion characteristics by applying pilot injection for improving the deterioration of combustibility caused by the higher viscosity of the BDF20 with the combustion flames taken by a high-speed camera and the cylinder pressure diagram. A 4-cycle single-cylinder diesel engine was remodeled to a visible 2-cycle engine taking the flame photographs, which has a common-rail injection system. The test was done laboratory temperature at $5{\sim}6^{\circ}C$. The results obtained are summarized as follows, (1) In the case of without pilot injection, the flame propagation speed was slowed and the maximum combustion pressure became lower. The phenomena became further aggravated as the fuel viscosity gets higher. (2) In the case of with pilot injection, early stage of combustion such as rapid ignition timing and flame propagation was activated since intermediate products formed by pilot injection act as a catalyst for combustion of main fuel.

• 한국추진공학회지
• /
• 제16권6호
• /
• pp.41-47
• /
• 2012

연소 불안정 현상을 완전하게 이해하기 위해서는 천이 과정과 한계 진폭과 같은 비선형 거동에 대한 예측이 매우 중요하다. 가스터빈 희박 예혼합 연소기에서 이러한 비선형 거동은 화염의 비선형 동특성에 크게 의존하게 된다. 본 연구에서는 기존에 선형 해석으로부터 비선형 열음향 해석으로 확장하기 위해서 화염 묘사 함수를 통한 시스템 안정성 해석 기법이 소개되었다. 이를 위하여, 주파수 뿐만 아니라 속도 진폭에 따른 열발생율의 변동 특성이 실험 결과로부터 모델링되었다. 현재 해석 조건에서 비선형 모델링 결과, 주어진 연소기 길이에서 속도 진폭이 불안정 주파수에 미치는 영향은 미비하였으나, 성장률에는 크게 영향을 미치는 것으로 나타났다. 향후 다양한 조건에서 비선형 모델의 검증과 한계 진폭의 예측 결과에 대한 실험 결과와의 비교가 요구된다.

• 해양환경안전학회지
• /
• 제18권1호
• /
• pp.55-60
• /
• 2012

매연과 다중고리 방향족 탄화수소의 생성에 대하여 n-헵탄의 혼합의 영향을 알아보기 위하여 순수에틸렌 대향류 확산화염에 n-헵탄을 소량 혼합하여 실험을 수행하였다. 매연체적분율과 PAH의 생성 계측에서는 레이저 유도 형광법 (laser-induced fluorescence; LIF)과 레이저 유도 백열법(laser-induced incandescence; LII)의 레이저 계측법을 이용하였다. 실험결과로 순수 에틸렌 화염에 소량의 n-헵탄을 혼합한 경우에는 매연과 다중고리 방향족 탄화수소가 상승하였다. 그러나 20% n-헵탄 혼합화염의 경우 LIF 신호가 감소하였다. 소량의 혼합화염의 경우, 다중고리 방향족 탄화수소와 매연의 상승은 n-헵탄 혼합에 의해 저온 영역에서의 메틸 라디칼의 증가로 의한다고 사료된다. 10% n-헵탄 혼합화염에 대한 화학반응 프로세스를 살펴본 결과 H 라디칼에 의한 반응율이 벤젠 생성에 결정적인 역할을 한다는 것을 알 수 있었다.

• 해양환경안전학회지
• /
• 제18권2호
• /
• pp.139-144
• /
• 2012

매연 생성에 대하여 톨루엔의 영향을 알아보기 위하여 순수에틸렌 대향류 확산화염에 톨루엔을 소량 혼합하여 수치해석을 수행하였다. 톨루엔($C_7H_8$)의 혼합 비율은 3%, 5%, 10%, 및 20%로 하였다. 계산에는 CHEMKIN III 기반의 Senkin 코드와 oppdif 코드를 이용하여 0-D 계산과 1-D 계산을 수행하였다. 0-D의 Senkin 계산에서는 톨루엔의 혼합율이 증가할수록 메틸라디칼의 농도는 증가하고 이에 따른 벤젠의 농도도 증가하였다. 이는 순수 에틸렌 화염에 톨루엔을 혼합할 경우 더 많은 매연이 생성될 것이라는 걸 의미한다. oppdif 코드에 의한 1-D 계산에서는 10% 톨루엔 반응식으로부터는 H 라디칼의 생성율이 결정적인 역할을 한다는 것을 알 수 있었다. 위 결과들로부터 확산화염 내 매연 생성에 있어 메틸라디칼, 벤젠과 H 라디칼이 중요한 역할을 한다는 것을 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제25권1호
• /
• pp.47-58
• /
• 2014

The characteristics of flame shape, laminar burning velocity, emissions and heat flux of stagnation point in premixed impinging jet flame of syngas fuel with 10% hydrogen content were experimentally investigated. Also, the adiabatic temperature and burning velocity are calculated by Chemkin package with USC-II mechanism. The equivalence ratios(0.8~5.0) and dimensionless separation distance(2.0~5.0) with fixed Reynolds number(1800) are main parameters in this work. Different flame shapes and colors were observed for different impingement conditions. The experimental results of burning velocity by flame surface area have a consistent with previous works and numerical simulation of this work. The inner flame length could be predicted with the ratio of mixture velocity and burning velocity from a simple formulation by the laminar burning velocity definition. It has been observed that the heat fluxes at stagnation point are directly affected by the flame shape including the separation distance. The emission results in impinging flame of syngas fuel show that the characteristics of $NO_x$ emission traced well with adiabatic temperature trend and CO emission due to fuel rich condition increased continuously with respect to the equivalence ratio.

• 한국수소및신에너지학회논문집
• /
• 제25권1호
• /
• pp.59-71
• /
• 2014

An experimental study has been conducted to investigate the heat transfer characteristics of laminar syngas/air mixture with 10% hydrogen content impinging normally to a flat plate of cylinder. Effects of impinging distance, Reynolds number and equivalence ratio as major parameters on heat fluxes of stagnation point and radial direction were examined experimentally by the direct photos and data acquisitions from heat flux sensor. In this work, we could find the incurved flame behavior of line shaped inner top-flame in very closed distance between flat plate and burner exit, which has been not reported from general gas-fuels. There were 3 times of maximum and 2 times minimum heat flux of stagnation point with respect to the impinging distance for the investigation of Reynolds number and equivalence ratio effect. It was confirmed that the maximum heat flux of stagnation point in 1'st and 2'nd peaks increased with the increase of the Reynolds number due to the Nusselt number increment. There was a third maximum rise in the heat flux of stagnation point for larger separation distances and this phenomenon was different each for laminar and turbulent condition. The heat transfer characteristics between the stagnation and wall jet region in radial heat flux profiles was investigated by the averaged heat flux value. It has been observed that the values of averaged heat flux traced well with the characteristics of major parameters and the decreasing of averaged heat flux was coincided with the decreasing trend of adiabatic temperature in spite of the same flow condition, especially for impinging distance and equivalence ratio effects.

• 한국추진공학회지
• /
• 제17권5호
• /
• pp.121-131
• /
• 2013

V-거터형 보염기가 장착된 덕트형 연소기에서 연소 불안정이 발생할 때 보염기 근처에서 나타나는 화염의 동특성에 대한 실험적 연구를 수행하였다. 화염 구조를 가시화하기 위해서 고속 카메라를 이용한 자발광 계측과 PIV 기법을 사용하였다. 연소 불안정이 발생하면 연소기 내부의 압력 구배에 변화가 생기면서 화염의 역화 현상이 일어나고, 역화의 진행거리는 당량비에 따라서 달라졌다. 역화의 진행거리와 구조에 따라 불안정 화염을 세 가지 유형으로 분류하였다. 일정 당량비 이상에서는 역화가 진행됨에 따라 보염기 앞쪽 끝단에서 특이한 화염 구조를 관측할 수 있었다. 순압력 구배에서 역화 되었던 화염면은 후류로 밀리고, 이때 보염기 안쪽에 형성된 와류로 인하여 재안정화가 이루어지는 것을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2181-2185
• /
• 2008

Fuel processing systems which convert HC fuel into $H_2$ rich gas (such as stream reforming, partial oxidation, auto-thermal reforming) need high temperature environment($600-1000^{\circ}C$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1-5kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural & anode off gas as reformer fuel. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity.

• 동아시아식생활학회지
• /
• 제2권1호
• /
• pp.57-68
• /
• 1992

In order to obtain the information on the status of using university cafeteria and students' preferences, the survey was conducted through questionaires to 434 students(male:195, female : 239) of 8 universities - 2 universities employed dietitian and 6 universities which didn't employ dietitian -through all the area of Incheon from 19th November 1990 to 14th December, 1990. The results obtained were as follows. 1) For keeping temperature of meals until service to students Refrigerator or warming cabinet or putting meals on low flames were used, and the amount for one person was almost decided by rough estimation by experience. All the foods remained were discarded. Also most of the cooking manager's age were from 50 to 59 and almost cooking managers graduated middle school. The fuel to cook was gas or kerosene. Method to disinfect tableware was boiling. 2) In case of the frequency of using university cafeteria, male students used cafeteria more often than female students, and regardless of sex students made use of cafeteria for lunch more than for breakfast and supper. Students also used university cafeteria not employing dietitian more than cafeteria employing dietitian. Disregarding of male, female, cafeteria employing cafeteria not employing dietitian, all students pointed out that main reason for using cafeteria were 'low price' and 'no other place to eat' And minor reasons were ' good taste' and 'meal quality'. On the contrary, the case of not using cafeteria were 'waiting in line' to male students, 'poor taste' to female students, 'waiting in line' and 'no varieties' on the cafeteria which employed dietitian, 'poor taste' and 'poor hygienes' on the cafeteria which didn't employ dietitian. 3) Considering of the preferences of menu, both male and female students liked "Bibim Bab" And male students prefered meals which contained broth both but female students prefered a light meals. 4) the difference of preferences showed that female student's preferences were high at all foods, and the preferences of fruits were high for both students. In detail, male students liked port, liver and small intestine of cattle, oyster and beans boiled in soysauce. But female students likde milk, yogurt and cucumber.