• Steel and Composite Structures
• /
• 제6권6호
• /
• pp.531-555
• /
• 2006

H-shaped welded steel column members are fabricated by welding together pre-cut flanges and the web. Modern fabricators are increasingly using plasma-cutting technique instead of traditional flame cutting. Different fabrication techniques result in different degrees of geometric imperfections and residual stresses, which can have considerable influence on the strength of steel columns. This paper presents the experimental investigation based temperature profiles, geometric imperfections, and built-in residual stresses in plasma cut-welded H-shaped steel column members and in similar flame cut-welded H-shaped steel columns. Temperature measurements were taken during and immediately after the cutting operations and the welding operations. The geometric imperfections were established at closely spaced grid locations on the original plates, after cutting plates into plate strips, and after welding plate strips into columns. Geometric imperfections associated with plasma cut element and members were found to be less than those of the corresponding elements and members made by flame cutting. The "Method of Section" technique was used to establish the residual stresses in the plate, plate strip, and in the welded columns. Higher residual stress values were observed in flame cut-welded columns. Models for idealized residual stress distributions for plasma cut and flame cut welded sections have been proposed.

• 펄프종이기술
• /
• 제44권5호
• /
• pp.14-20
• /
• 2012

In this paper, the flame-retardant wall paper was successfully prepared with recycled polyethylene terephthalate (PET) short cut fiber with flame-retardant property and wood pulp using polyvinyl alcohol (PVA) as binder followed by treatment of non-halogen flame retardant. Physical properties such as formation index, tensile strength, elongation, and burst strength increased as defibrillation increased except tear strength. Bulk increased but formation index, tensile strength, elongation and burst strength decreased along with addition of PET short cut fiber. It was also found that tear strength rose significantly up to 30% of PET short cut fiber and then declined (fell) rapidly. As addition level of PVA increased tensile strength, elongation and burst strength increased, but tear strength decreased slightly. Addition of 20% of PET short cut fiber and 13% of PVA provided the flame-retardant wall paper with both improved flameproofing and physical properties.

• 한국연소학회지
• /
• 제22권1호
• /
• pp.32-38
• /
• 2017

This paper shows the dynamics of the Burke-Schumann flame. To show flame dynamics, this paper measures the flame surface and heat release rate. The flame shape is divided into three types with forcing frequencies. When the forcing frequency is lower than 120 Hz, the upper region of flame is cut. The flame is stagnant with 220 to 280 Hz forcing frequencies. The rest conditions of forcing frequencies make the connected wave shape of flame. The heat release rate is expressed by the flame transfer function. The gain of the flame transfer function is similar with the oscillation magnitude of the flame area except for flame cutting conditions. The flame is cut because the fuel is not supplied to upper flame region.

• Journal of the Korean Wood Science and Technology
• /
• 제44권4호
• /
• pp.589-599
• /
• 2016

Korean wooden cultural heritages are treated by flame retardants to protect fire hazards. Two types of flame retardants are used to treat wooden cultural heritage. These flame retardants cause some problems such as surface whitening, discoloration, and cracks due to the chemical reaction caused by Korean traditional wood painting (Dancheong), flame retardant and wood humidity. The Korean government is trying to cut down on the amount of flame retardants for the wooden cultural heritage because of these problems. This study was carried out to find the cause of whitening by flame retardants treatment. The reaction between pigment and flame retardant chemicals was analyzed by infrared spectroscopy.

• 농업과학연구
• /
• 제40권4호
• /
• pp.305-309
• /
• 2013

A freesia (Freesia hybrida Hort.) 'Dancing Flame' was developed for the cut flower in the National Institute of Horticultural Herbal Science in 2007. This hybrid was selected from a crossing between a seedling 'Vulcano' and 'Sailor', which is scarlet double flowering and purple single flowering, respectively, and 'Figaro' which is bright red color and semi-double flowering, in 2000. Morphological characteristics of the selected hybrid were investigated for 3 years from 2005 to 2007, and then it was named 'Dancing Flame'. 'Dancing Flame' had red color (RHS R44B) and single flower with yellow center color (RHS Y9A). The growth of the plant was vigorous and the average height was 93.3 cm. The average flower width was 60 mm, number of floret per stalk was 14.3, and stalk was 13.2 cm length. The average yield, 7.8 cuttings per plant, was 2.5 stems per plant more than the control cultivar. The average days to first flowering of 'Dancing Flame', 133 days, was approximately 5 days earlier than the control cultivar. And its average yield, 7.1 cormlet per plant, was also 2.5times more than the control cultivar.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.365-369
• /
• 2004

The Advantages of hot machining are the reduction of cutting forces, tool wear, and the increase of material removal rates. In this study, a hot-machining using gas flame heating characteristics of milling by CBN tip was analyzed, and the influence of the surface temperature and the depth of cut on the tool life were investigated. The results show that hot machining of tungsten carbide-alloyed is more effective than conventional machining. In addition, some advantages obtained from hot machining, such as decrease of tool wear and cutting force, high surface quality.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기설비전문위원
• /
• pp.90-92
• /
• 2005

When the jacket damaged conductors in 22.9kV-y overhead distribution lines are contacted with the metal material by strong wind, which, leads to are melting as well as faults accordance. The duration of the arc temperature due to flame effected by weather and flash over conditions. In order to simulated the worst conditions, the ACSR-OC($58mm^2$) used as specimen was artificially cut in no wind. After contacting the two cut conductors again the testing current was applied. thus, the changes in temperature of are flame was analyzed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 춘계학술발표 개요집
• /
• pp.26-27
• /
• 1996

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2011년도 후기공동학술대회 논문집
• /
• pp.88-89
• /
• 2011

The study on synthesis of carbon nanomaterials by H2 mixing in counterflow methane diffusion flames has been experimentally conducted. We have also investigated on effect of catalyst and temperature in flame. The counterflow flame was formed by many kind of gas (fuel side using $CH_4-H_2-N_2$ and oxidizer side $N_2-O_2$) and nitrogen shields discharge on each other side to cut off oxidizer of the atmosphere. Ferrocene was used as a metal catalyst for CNTs synthesis. substrate was used to deposit carbon nanomaterials and these were analyzed by FE-SEM. We could find that carbon nanotubes and many kind of carbon nano materials were formed in Cu wire substrate, through this experiment.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.632-632
• /
• 2009

The purpose of this study is to present the range of defects mentioned in the Product Liability (PL) and to establish an objective basis and grounds for the analysis of accidents expected to happen by analyzing and presenting the external flame pattern and electrical characteristics of an LED streetlight lamp, a new lighting lamp. From the analysis of the cross-section of a cable carbonized by an external flame, it was observed that the wire's strand and insulation material had solidly adhered, and that greater voids were formed at the surface than at the center. Irregular carbide lumps were formed in the globe directly exposed to the flame, and the globe carbonized by the indirect flame showed characteristics that they had melted and flowed downward. It was found that the forward and backward resistances of the normal LED were approximately 1.74 [$M{\Omega}$] and 140 [$M{\Omega}$], respectively. The lamp burnt by the strong flame exhibited infinite forward and backward resistances and the LED did not emit light. The carbonized LED lamp was gray and exhibited fine delaminations. According to the Product Liability, a product defect signifies a simple product defect. Most of the defects were caused by the lack of stability, and the defect of the product itself occurred during the design and manufacture. The defects in warnings and markings include an insufficiency of handling manuals and warnings, expressive warranty violations, defective markings, etc. In order to prevent an accident resulting from a product, it is necessary to prepare safety warnings and documentation, establish clear-cut lines of liabilities, and subscribe insurances. However, it could be seen that important factors against the Product Liability were product improvement, response to compensation requests and law suits, credit restoration, etc.