• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.208-214
• /
• 1993

Pyrolysis of bituminous coal has been carried out in a two-stage fixed bed reactor to produce high heating value gas(7000 kcal/N㎥) for industrial or town gas usage. The effects of coke catalyst, pyrolysis temperature (468∼565$^{\circ}C$), and catalytic cracking temperature (700∼850$^{\circ}C$) on the product gas properties from pyrolysis of bituminous coal have been determined. From pyrolysis of Dong Jin coal with coke, the carbon deposition on catalyst is found to be less than 5% of product tar and approximately 15% of total energy iii the parent coal can be recovered as high heating value gas. Oil composition in the product tar from the two-stage pyrolysis is higher than that from low-temperature pyrolysis. The tar produced from pyrolysis below 516$^{\circ}C$ can be easily catalytically cracked but, the tar produced above 565$^{\circ}C$ cannot be cracked easily with catalyst. From the product gas analysis, the catalytic cracking temperature should be maintained below 800$^{\circ}C$ since cracking speed of ethylene increases remarkably with the cracking temperature above 800$^{\circ}C$.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.73-80
• /
• 1998

Zinc titanate sorbents were prepared and regeneration of used sorbents for high temperature desulfurization of fuel gases was studied. Zn/Ti molar ratio of prepared sorbents was 1.5 and quartz fixed-bed reactors with 1 cm and 3 cm diameters were used. Regeneration of zinc titanate sorbents at high temperature is exothermic reaction; that brings about deterioration of sorbents. Therefore, we experimented regeneration reaction of zinc titanate sorbents for the purpose of obtaining the most suitable regeneration conditions by changing experimental parameters such as reaction temperature, oxygen concentration, flow rate and steam content. $H_2S$ and $SO_2$ breakthrough curves were obtained during desulfurization-regeneration. Also, properties of the sorbents before and after regeneration were analyzed using SEM, XRD, Hg-porosimetry and BET method. From such results, we obtained the most suitable regeneration conditions including regeneration temperature of 650$^{\circ}$C, $O_2$ content of 5% and steam content of 10% in the gas stream.

• The Korean Journal of Emergency Medical Services
• /
• v.5 no.1
• /
• pp.177-198
• /
• 2001

The purpose of this research which was conducted by surveying the transfer consultation records from 360 medical institutions such as general hospitals, hospitals, clinics to the Emergency Medical Center at E University Hospital for six months(Jan. 1, 2000 - Jun. 30, 2000) are to standardize & complete transfer consultation record of hospitals at the 1st & 2nd referral level and to give patients transferred emergency medical center medical information services on a better quality. The conclusions and suggestions from this study were summarized as follows; (1) Examing the distribution of the referral medical consultation(transfer) sheet type, surgery part local clinic sheet types were 34.4%, medical part local clinic sheet types were 26.7%, undifferentiated local clinic sheet types were 23.9% and hospital level sheet types were 15.0%. (2) The items of the transfer consultation records had been standardized more than 75% in the order of patient's name, date, doctor's name, diagnosis, patient's status, impressions. (3) That the degree of recording completion on these items is in the order of patient's name, date, diagnosis, impressions was revealed. (4) Because the standardization and the degree of recording completion are very low in the patient's gender, age, address, electronic recording system was needed for more perfect input of initial patient informations. (5) This standardizing & complete recording on examination and medication will prevent re-examination and abuse of medication for patients transferred emergency medical center. (6) EMT Transfer System should be fixed in all medical institute for the standardizing & complete recording on care period and departure time will give many emergency patients the proper treatments at the proper time. (7) It was revealed that developing new standardized transfer consultation record & using electronic recording system are needed. (8) The complete recording & Fast Track System were needed for higher rate of bed operation at emergency medical center and more hospital profit.

• Journal of Hydrogen and New Energy
• /
• v.21 no.1
• /
• pp.50-57
• /
• 2010

Stepwise production of syn-gas and hydrogen from methane on ferrite based media added with yttria-stabilized zirconia (YSZ) was carried out using a fixed bed infrared reactor. In this study, all M-ferrite (M=Co, Cu, Mn and Ni) media were prepared by co-precipitation method, and there the YSZ was added as a binder to improve thermal stability, reactivity, and resistance against carbon deposition. Most of the ferrite media containing YSZ showed the good redox property for temperature programmed reduction/oxidation (TPR/O) tests. Notably, the Cu-substituted ferrite medium with YSZ showed the great resistance against carbon deposition as well as the good reactivity for the stepwise production of syngas and hydrogen. Furthermore, it also showed the good durability without significant deactivation during five repeated cyclic tests.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.8
• /
• pp.865-871
• /
• 2012

Because of the increasing cost of oil and natural gas, energy production technologies using coal, including synthetic natural gas (SNG) and integrated gasification combined cycle (IGCC), have attracted attention because of the relatively low cost of coal. During the early stage of a project, the developer or project owner has many options with regard to the selection of a gasifier. In particular, from the viewpoint of feasibility, the gasifier is a key factor in the economic evaluation. This study compares the technical aspects of gasifiers for a real SNG production project in an early stage. A fixed-bed slagging gasifier, wet-type entrained gasifier, and dry-type entrained gasifier, all of which have specific advantages, can be used for the SNG production project. Base on a comparison of the process descriptions and performances of each gasifier, this study presents a selection guideline for a gasifier for an SNG production project that will be beneficial to project developers and EPC (Engineering, Procurement, Construction) contractors.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.289-295
• /
• 2003

Synthesis gas is produced commercially by a steam reforming process. However, the process is highly endothermic and energy intensive. Thus, this study was conducted to produce synthesis gas by the partial oxidation of methane to cut down the energy cost. Supported Ni catalysts were prepared by the impregnation method. To examine the activity of the catalysts, a differential fixed bed reactor was used, and the reaction was carried out at $750{\sim}850^{\circ}C$ and 1 atm. The fresh and used catalysts were characterized by XRD, XPS, TGA and AAS. The highest catalytic activity was obtained with the 13wt% Ni/MgO catalyst, with which methane conversion was 81%, and $H_2$ and CO selectivities were 94% and 93%, respectively. 13wt% Ni/MgO catalyst showed the best $MgNiO_2$ solid solution state, which can explain the highest catalytic activity of the 13wt% Ni/MgO catalyst.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.4
• /
• pp.444-451
• /
• 2007

Catalytic oxidation characteristics of benzene as a VOC was investigated using a fixed bed reactor system over transition $metals/\gamma-Al_2O_3$ catalysts. As transition metals, eight metals including copper, nickel, manganese, iron etc. were adopted. The parametric tests were conducted at the reaction temperature range of $200\sim500^{\circ}C$, benzene concentration of $1,000\sim3,000$ ppm, and space velocity range of $5,000\sim60,000\;hr^{-l}$. The property analyses such as BET, SEM, XRD and the conversions of catalytic oxidation of VOC were examined. The experimental results showed that the conversion was increased with decreasing VOC concentration and space velocity. It was also found that $Cu/\gamma-Al_2O_3$ catalyst calcinated at $500^{\circ}C$ showed the highest activity for the oxidation of benzene and 15% metal loading was the optimum impregnation level.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.4
• /
• pp.443-448
• /
• 2010

The objective of this study was to assess the catalytic activities of manganese oxide (MnO, $MnO_2$, $Mn_2O_3$, and $Mn_3O_4$) catalysts for odors (acetaldehyde and propionaldehyde) removal. We used a fixed bed reactor as the experimental apparatus and the catalytic performance were carried out over the temperature range of $200{\sim}470^{\circ}C$. The properties and performance of catalysts were characterized by the X-ray diffraction (XRD) and Brunauer Emmett Teller (BET). The catalytic activities of manganese oxide catalysts for acetaldehyde combustion were in the order of MnO < $MnO_2$ < $Mn_2O_3$ < $Mn_3O_4$, and it is similar to that of propionaldehyde combustion. We also confirmed that the reactions have well followed the kinetic model of Power-Rate Law and the reaction order (n) is 1 for both of the acetaldehyde and propionaldehyde combustion. In addition, the reaction activation energy of acetaldehyde and propionaldehyde combustion over $Mn_3O_4$ were found to be $72.42\;kJmol^{-1}$ for 487~503 K and $51.14\;kJmol^{-1}$ for 473~533 K, respectively.

• New & Renewable Energy
• /
• v.6 no.4
• /
• pp.30-40
• /
• 2010

Syngas from gasification of coal can be converted to SNG(Synthesis Natural Gas) through gas cleaning, water gas shift, $CO_2$ removal, and methanation. One of the key technologies involved in the production of SNG is the methanation process. In the methanation process, carbon oxide is converted into methane by reaction with hydrogen. Major factors of methanation are hydrogen-carbon oxide ratio, reaction temperature and space velocity. In order to understand the catalytic behavior, temperature programmed surface reaction (TPSR) experiments and reaction in a fixed bed reactor of carbon monoxide have been performed using two commercial catalyst with different Ni contents (Catalyst A, B). In case of catalyst A, CO conversion was over 99% at the temperature range of $350{\sim}420^{\circ}C$ and CO conversions and $CH_4$ selectivity were lower at the space condition over 3000 1/h. In case of catalyst B, CO conversion was 100% at the temperature over $370^{\circ}C$ and CO conversions and $CH_4$ selectivity were lower at the space condition over 4700 1/h. Also, conditions to satisfy $CH_4$ productivity over 500 ml/h.g-cat were over 2000 1/h of space velocity in case of catalyst A and over 2300 1/h of space velocity in case of catalyst B.

• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.240-248
• /
• 1990

The catalytic activity and selectivity of metal loaded H-mordenite for transalkylation of $C_9$ aromatics were studied in a continuous flow fixed bed reactor under high pressure. Nickel loaded H-mordenite(T-Ni) catalyst showed high activity and slow decay of activity. Molybdenum and nickel loaded H-mordenite(T-NiMo) catalyst also showed high activity and suppressed coking of hydrocarbons. The selectivity of xylene for T-Ni and T-NiMo catalysts decreased with temperature, but that for T catalyst(commercial grade) monotonically increased with temperature within the experimental range. The performance of T-Ni and T-NiMo catalysts was better than that of T catalyst in terms of initial activity and its decay. The addition of Mo improved slightly stability of T-Ni catalyst.