• Korean Membrane Journal
• /
• 제7권1호
• /
• pp.34-41
• /
• 2005

The wastewater discharged from a paper plant was filtrated by 3 kinds of tubular carbon ceramic UF and MF membranes with $N_2$-backflushing. The filtration time (FT) was fixed at 8 min or 16 min, and $N_2$-backflushing time (BT) was changed in 0${\~}$60 sec. The optimal condition was discussed in the viewpoints of total permeate volume ($V_T$), dimensionless permeate flux (J/Jo) and resistance of membrane fouling ($R_f$). In the viewpoints of $V_T$, J/Jo and $R_f$, the optimal $N_2$-BT was 40 sec at both FT for M9 (MWCO: 300,000 Daltons) and C005 ($0.05{\mu}m$) membranes. However, for C010 ($0.1{\mu}m$) it was 10 sec at FT=8 min, and 20 sec at FT=16 min in the viewpoints of J/Jo and $R_f$, and 5 sec at both FT in the viewpoints of $V_T$. It means that the short $N_2$-BT could reduce the membrane fouling and recover the permeate flux sufficiently for MF membrane having a large pore size as C010. Average rejection rates of pollutants were higher than $99.0\%$ for turbidity and $22.8{\~}59.6\%$ for $COD_{cr}$, but rejection rates of total dissolved solid (TDS) were lower than $8.9\%$. Therefore, the low turbidity water purified in our system could be reused for paper process.

• 한국패류학회지
• /
• 제17권2호
• /
• pp.95-104
• /
• 2001

To determine optimal conditions for measurement of the clearance rate in feeding experiment of an intertidal bivalve Glauconome chinensis, effects of starvation, extent of mixing at subsampling, and initial prey concentration were assessed. Experiments were conducted separately for each condition with different treatments. Two-way ANOVAs showed that there were significant differences in clearance rates among different starvation periods (p<0.001), extents of mixing (p = 0.005), and prey concentrations (p < 0.001). Starvation for 1 or 2 days gave rise to 2 to 3-fold increase in the clearance rate. After starvation for 5 days, the clearance rate decreased seriously, implying loss of physiological status. It is suggested that animals should be fed during acclimation. The differences of the clearance rates between gentle and vigorous mixings were significant, but the differences were smaller than that among different incubation times. It was found that vigorous mixing is not necessary. The effect of initial prey concentration was great. However, optimal prey concentration could not be determined at any fixed value. Experiments with multiple concentrations of algal prey are recommended. Optimal incubation time for measurement of the clearance rate of G. chinensis was determined to be 2-4 hours.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권6호
• /
• pp.340-349
• /
• 2004

Recently, the needs and concerns for the power loss are increasing according to the energy conservation at the level of the national policies and power utilities's business strategies. Especially, the issue of the power loss is the main factor for the determining the electric pricing rates in the circumstances of the deregulation of electrical industry. However, because of the lacking of management for power loss load factors (LLF), it is difficult to make a calculation for the power loss and to make a decision for the electric rates. And loss factor(k-factor), which is a most important factor for calculation of the distribution power loss, has been used as a fixed value of 0.32 since the fiscal year 1973. Therefore, This study presents the statistical calculation methods of the loss factors classified by load types and seasons by using the practical data of 65 primary feeders which are selected by proper procedures. Based on the above the algorithms and methods, the optimal method of the distribution loss management classified by facilities such as primary feeders, distribution transformers and secondary feeders is presented. The simulation results show the effectiveness and usefulness of the proposed methods.

• 소성∙가공
• /
• 제19권6호
• /
• pp.357-362
• /
• 2010

Dry sliding wear behavior of pure Fe and Cu which have BCC and FCC crystal structure, respectively, was investigated. The wear characteristics of the pure metals with different crystal structure were compared. Dry sliding wear tests were carried out using a pin-on-disk wear tester at various loads under the constant sliding speed condition of 0.15 m/s against a silica ball at room temperature. Sliding distance was fixed as 600 m for all wear tests. Wear rate of a specimen was calculated by dividing the weight loss of the specimen after the test by the specific gravity and sliding distance. Worn surfaces and wear debris were analyzed by SEM. The wear of both pure Fe and Cu proceeded with surface deformation, resulting in similar wear rates despite of their structure difference under the current test conditions. Wear rates of both metals were low if the surface deformation due to wear forms thick surface-deformation layer that is strain hardened beneath the wearing surface. The pure Cu specimens showed a lot of oxides on the worn surface when tested at low loads less than 5 N, which resulted in very low wear rate.

• KIEE International Transactions on Power Engineering
• /
• 제5A권2호
• /
• pp.109-115
• /
• 2005

Recently, the needs and concerns regarding power loss have been increasing according to energy conservation at the level of the national policies and the business strategies of power utilities. In particular, the issue of power loss is the main factor for determining rates for electrical consumption in the deregulation of the electrical industry. However, because of the lack of management for power loss load factors (LLF) it is difficult to make a calculation for power loss and to make a decision concerning the electric rates. Furthermore, loss factor (k-factor) in Korea, which is of primary significance in the calculation of distribution power loss, has been used as a fixed value of 0.32 since the fiscal year 1973. Therefore, this study presents the statistical calculation methods of the loss factors classified by load types and seasons by using the practical data of 65 primary feeders that have been selected by appropriate procedures. Based on the above, the algorithms and methods, as well as the optimal method of the distribution loss management classified by facilities such as primary feeders, distribution transformers and secondary feeders is presented. The simulation results demonstrate the effectiveness and usefulness of the proposed methods.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1490-1492
• /
• 1994

Diamond thin films were deposited on Si substrate from $CH_4-H_2-O_2$ system by MWPECVD at the condition of power of 800W, pressure of 80torr, $H_2$ flow rate of $75{\sim}81sccm$, $O_2$ flow rate of $0{\sim}3.8sccm$, $CH_4$ flow rate of $4.8{\sim}9sccm$, substrate temp, of $950{\sim}1010^{\circ}C$ and deposition time of 5hr. The deposited films were characterized by SEM, XRD and Raman spectroscopy. The growth rates of thin films and particles was measured. Good quality were synthesized at 40% of oxygen concentration which 6% of fixed metane concentration, and at 50%. Its deposition rates were $2.4{\mu}m/h$ respectively. As oxygen concentration increased, it was known that the broad peak of $1350 cm^{-1}$ was shifted to $1332cm^{-1}$ due to etching of carbon component.

• 전기화학회지
• /
• 제9권2호
• /
• pp.77-83
• /
• 2006

Anodic overpotential has been investigated with gas composition changes in a $100cm^2$ class molten carbonate fuel cell. The overpotential was measured with steady state polarization, reactant gas addition (RA), inert gas step addition (ISA), and electrochemical impedance spectroscopy (EIS) methods at different anodic inlet gas compositions, i.e., $H_2:CO_2:H_2O=0.69:0.17:0.14\;atm\;and\;H_2:CO_2:H_2O=0.33:0.33:0.33\;atm$, at a fixed $H_2$ flow rate. The results demonstrate that the anodic overpotential decreases with increasing $CO_2\;and\;H_2O$ flow rates, indicating the anode reaction is a gas-phase mass-transfer control process of the reactant species, $H_2,\;CO_2,\;and\;H_2O$. It was also found that the mass-transfer resistance due to the $H_2$ species slightly increases at higher $CO_2\;and\;H_2O$ flow rates. EIS showed reduction of the lower frequency semi-circle with increasing $H_2O\;and\;CO_2$ flow rate without affecting the high frequency semi-circle.

• 전자공학회논문지CI
• /
• 제38권6호
• /
• pp.93-105
• /
• 2001

격자 벡터 양자화의 비 손실 과정에서는 생성된 코드단어들을 radius 열과 Index 열로 열거한다. radius 열은 run-length 부호화한 한 다음 Entropy 부호화한다. 또한 index 열들은 이진의 고정길이로 표현한다. 비트율이 증가함에 따라 index 비트는 선형적으로 증가하여서 부호화 성능을 감소시킨다. 이 논문에서는, 넓은 비트율의 범위에서 index 비트를 줄이기 위해서, set partitioning 방식을 채택한 새로운 열거 알고리즘을 개발하였다. 제안된 열거 방법은 큰 index 값을 작은 값들을 천이 시켜서 index 비트를 줄인다. 제안된 비손실 기법을 웨이블릿 기반의 영상 부호화에 적용시켰을 때, 0.3 bits/pixel 이상의 비트룰에서 기존의 비손실 부호화 방식보다 10%이상의 비트율을 감소시켰다.

• 한국자동차공학회논문집
• /
• 제23권6호
• /
• pp.656-662
• /
• 2015

In the present study, multi-layered Si DLC (Silicon Diamond-Like Carbon) coatings with HMDSO (Hexamethyldisiloxane) buffer layers are applied on SKD 11 substrates by PECVD (Plasma Enhanced Chemical Vapor Deposition) with different HMDSO gas flow rates, while the gas flow rate of $C_2H_2$ is fixed to enhance the electric resistivity of forming dies for electrically assisted forming. The HMDSO buffer layer is introduced to increase adhesion between the base metal and Si-DLC layers. The result of evaluation of electric resistivity and adhesion strength shows that the properties are affected by the flow rate of HMDSO, while the flow rate of 80 sccm results in the coating with the highest electric resistivity and adhesion strength among the selected flow rates.

• Journal of Information Processing Systems
• /
• 제5권3호
• /
• pp.151-158
• /
• 2009

This paper proposes a utility-based data rate allocation algorithm to provide high-quality mobile video streaming over femtocell networks. We first derive a utility function to calculate the optimal data rates for maximizing the aggregate utilities of all mobile users in the femtocell. The total sum of optimal data rates is limited by the link capacity of the backhaul connections. Furthermore, electromagnetic cross-talk poses a serious problem for the backhaul connections, and its influence passes on to mobile users, as well as causing data rate degradation in the femtocell networks. We also have studied a fixed margin iterative water-filling algorithm to achieve the target data rate of each backhaul connection as a counter-measure to the cross-talk problem. The results of our simulation show that the algorithm is capable of minimizing the transmission power of backhaul connections while guaranteeing a high overall quality of service for all users of the same binder. In particular, it can provide the target data rate required to maximize user satisfaction with the mobile video streaming service over the femtocell networks.