This article investigates the thermal and post-buckling problems of graphene platelets reinforced metal foams (GPLRMF) beams with initial geometric imperfection. Three distribution forms of graphene platelet (GPLs) and foam are employed. This article utilizes the mixing law Halpin Tsai model to estimate the physical parameters of materials. Considering three different boundary conditions, we used the Euler beam theory to establish the governing equations. Afterwards, the Galerkin method is applied to discretize these equations. The correctness of this article is verified through data analysis and comparison with the existing articles. The influences of geometric imperfection, GPL distribution modes, boundary conditions, GPLs weight fraction, foam distribution pattern and foam coefficient on thermal post-buckling are analyzed. The results indicate that, perfect GPLRMF beams do not undergo bifurcation buckling before reaching a certain temperature, and the critical buckling temperature is the highest when both ends are fixed. At the same time, the structural stiffness of the beam under the GPL-A model is the highest, and the buckling response of the beam under the Foam-II mode is the lowest, and the presence of GPLs can effectively improve the buckling strength.
This paper introduces a novel approach to time-series estimation for energy load forecasting within Virtual Power Plant (VPP) systems, leveraging advanced artificial intelligence (AI) algorithms, namely Long Short-Term Memory (LSTM) and Seasonal Autoregressive Integrated Moving Average (SARIMA). Virtual power plants, which integrate diverse microgrids managed by Energy Management Systems (EMS), require precise forecasting techniques to balance energy supply and demand efficiently. The paper introduces a hybrid-method forecasting model combining a parametric-based statistical technique and an AI algorithm. The LSTM algorithm is particularly employed to discern pattern correlations over fixed intervals, crucial for predicting accurate future energy loads. SARIMA is applied to generate time-series forecasts, accounting for non-stationary and seasonal variations. The forecasting model incorporates a broad spectrum of distributed energy resources, including renewable energy sources and conventional power plants. Data spanning a decade, sourced from the Korea Power Exchange (KPX) Electrical Power Statistical Information System (EPSIS), were utilized to validate the model. The proposed hybrid LSTM-SARIMA model with parameter sets (1, 1, 1, 12) and (2, 1, 1, 12) demonstrated a high fidelity to the actual observed data. Thus, it is concluded that the optimized system notably surpasses traditional forecasting methods, indicating that this model offers a viable solution for EMS to enhance short-term load forecasting.
에너지 절감형 서버 클러스터는 에너지 절감을 고려하지 않는 기존 서버 클러스터에 비해 서비스 품질을 보장하면서 전력소비를 절감하는 것을 목표로 한다. 에너지 절감형 서버 클러스터에서는 현재의 부하를 처리하는 데 필요한 최소수의 서버들만 ON 하도록 고정 또는 가변 주기로 서버들의 전원모드를 조정한다. 이에 대한 기존 연구들은 전력 절감 또는 서비스 품질을 보장하려고 노력해왔지만 에너지 효율성을 잘 고려하지는 못했다. 본 논문에서는 에너지 절감형 클러스터에서 자율학습기반의 에너지 효율적인 클러스터 관리 기법을 제안한다. 자율학습을 통해 최적화된 파라미터들을 이용하여 전력 소모 대비 최고의 성능을 얻을 수 있도록 서버 전원모드를 조정한다. 제안방법은 서버 전원모드 조정을 위해 아래의 과정을 반복 수행한다. 첫째, 현재 부하 및 트래픽 패턴을 보고 현재 워크로드 패턴 유형을 사전에 정의한 대로 분류한다. 둘째, 학습 테이블을 탐색하여 해당 워크로드 패턴 유형에 대해 예전에 학습이 수행되었는지 확인한다. 만일 수행되었다면 이미 저장된 파라미터를 이용한다. 그렇지 않으면, 학습을 수행하여 에너지 효율성 관점에서 최고의 파라미터를 얻어 저장한다. 셋째, 얻어진 파라미터를 이용하여 서버 전원모드를 조정한다. 제안방법을 구현하여 16개의 서버 클러스터 환경에서 3가지 다른 부하 패턴들을 이용하여 실험을 수행하였다. 실험 결과는 제안방법의 에너지 효율성이 뛰어남을 보여주고 있다. 뱅킹 부하패턴, 실제 부하패턴, 가상 부하패턴 각각에 대하여, 제안방법의 단위전력당 good 응답 수가 기존의 정적 서버 전원모드 제어방법의 99.9%, 107.5%, 141.8%이고, 기존의 예측방법의 102.0%, 107.0%, 106.8%이다.
The purpose of this study was to investigate the changes of morphology and structure of bone tissue, caused by administration of high-dose hydrocortisone, elcatonin and cyclophosphamide. In order to carry out experiment, 60 four-week old Sprague-Dawley strain rats weighing about 107 gms were selected and divided into experimental group and control group. The experimental group was subdivided into three groups, assigned fifteen rats for each group, by the different drugs administered. Each experimental group was then categorized as follows: hydrocortisone 30㎎/㎏ b.w. with daily subcutaneous injection, elcatonin 20U/㎏ b.w. with daily subcutaneous injection, and cyclophosphamide 100㎎/㎏ b.w. with a single intraperitoneal injection. Fifteen rats were injected daily with 5㎖/㎏ b.w. of normal saline solution subcutaneously in control group. Rats in control group and experimental group were serially sacrificed on the 6th, the 15th and the 22nd day after injection of normal saline, hydrocortisone, elcatonin and cyclophosphamide, respectively. Being sacrificed, both sides of mandibular condyles were removed and fixed with 10% neutral formaline. The one side of mandibular condyles was radiographed with soft X-ray apparatus. Thereafter, the obtained radiographs were observed, and the bone density of condylar head and condylar neck regions was measured by use of transferring video-based digital radiograph. The other side was further decalcified and embedded in paraffin as usual manner, then sectioned and stained with hematoxylin and eosin, observed by light microscope. The obtained results were as follows: 1. Sclerotic changes with regularly increased trabecular pattern were seen throughout experimental periods in hydrocortisone group. Increased the number of trabecular pattern with irregularity and periodic striation on the periphery of condylar head region were appeared with lapse of time in elcatonin group. In cyclophosphamide group, irregular trabecular pattern and stippled radiopacities on mandibular condyle were observed with lapse of time. 2. The bone density of condylar head region was increased in hydrocortisone group, decreased in elcatonin group, and tended to be decreased in cyclophosphamide group, compared with that of control group according to the experimental periods. 3. The bone density of condylar neck region tended to be rather increased in hydrocortisone group, elcatonin group and cyclophosphamide group, depending on the experimental periods. 4. In microscopic studies, there were irregular trabecular bonds and osteoblastic activity in hydrocortisone group and elcatonin group throughout experimental periods, degenerative cartilage and trabecular bones in the 6th day and densely calcified trabecular bones in the 22nd day in cyclophosphamide group.
본 연구는 남자 중학교 초보피험자들을 대상으로 태권도 돌려차기 동작의 숙련정도에 따른 운동학적 협응과 제어과정을 살펴보는 데 목적을 두었다. 이용된 변인은 최대합성직선속도와 각도 대 각도 도면이었다. 분석결과, 연습후기로 갈수록 인접한 분절간의 운동량 전이가 잘 이루어져 각 분절의 최대합성직선속도가 증가하였으며 무릎관절 최대굴곡 시까지는 엉덩관절과 무릎관절이 동형동조 협응형태로 변해갔으며, 최대굴곡 후 타격 시까지는 모든 숙련 단계에 있어서 이형동조 협응패턴을 나타내었다. 발목관절은 무릎관절 최대굴곡 시까지 배측굴곡 상태에서 저측굴곡으로 변했으며, 최대굴곡 후 타격시점까지는 발목관절은 고정시키고, 무릎관절은 신전시키는 자유도 고정 제어기전을 나타내었다.
Soldering is the usual method used to correct an unstable fixed partial denture framework at patient's try-in; However, presoldering base metal alloys is technique-sensitve and results are unstable because it is difficult to maintain uniform heat distribution and to prevent oxidation of an alloy. A cast-joining technique has been developed by Weiss and Munyon for repair, correction and addition to base metal framework. This joining technique eliminates the problem with presoldering of non-precious frameworks. The object of this study was to 1) compare the relative flexure strength and the joining effectiveness of Ni-Cr-Be cast in two pieces and 'pre-soldered' versus in two pieces and 'cast-joined'. 2) determine the effect of increasing the number of retentive grooves on the face of the cast and 3) determine the effect of the relative matched position of groove patterns on flexure strength. The joining effectiveness can be expressed by the ratio of the mean flexure stress of soldered or cast-joined specimens to that of one-piece cast. Resin rods 3mm in diameter were used as pattern of specimens for one-piece casted, presoldered, and cast-joined groups. Cast-joined specimens had two different patterns of retentive grooves on the joined faces. Type A had cross-shaped grooves 1mm in depth. 0.6mm in width. Type B was the same except for the addition of one more retentive groove. In the experiment connecting cast-joined specimens, half of specimens with type A pattern had their patterns on the faces of paired casts matched with each other as mirror image. With the rest pairs, it was proceeded that one of paired casts turned 45 degrees so that the patterns crossed. Half of specimens with type B pattern also had the patterns matched as mirror image; However, here, one of paired casts turned 90 degrees with the other pairs. Retentive groove in this study lacked the intentional undercuts, in contrast with the suggestion of Weiss and Munyon. The specimens were subjected to four-point flexural loading in an Instron testing machine. The midspan flexural stress was calculated at the point of initial plastic strain as determined from a strip-chart recorder or at the point of failure if this occured at a lower stress level. Within the scope of this study, the following results were obtained. 1. The presoldered group showed flexural strength at least 2 times higher than the cast-joined groups. Its joining effectiveness was 82%. 2. In cast-joined groups, the flexural strength of joints with type B patterns exhibited 1.5 times that of joints with type A patterns. Joining effectivenesses were 38% for type B patterns, 25-26% for type A patterns. 3. The relative matched position of groove patterns did not have any significant effect on flexural strength of the cast-joined specimens with either type A patterns or type B patterns(p>.05).
교합평면은 시상면적인 치열궁 형태를 나타내는 것으로, 악구강계를 구성하는 요소의 하나인 교합을 형태적으로 구성한다. 본 증례에서는 생체의 정중 시상면에 대한 수평, 측방좌표를 교합기상에 재현하여 상하악 치아 및 결손부 치조제에 대한 좌우 동적인 위치관계 얻기 위해 Shilla system (Hamans, Tokyo, Japan)을 이용하여 교합평면을 재구성 하였다. 본 증례의 환자는 41세의 남자 환자로 상악 전치부 10본금속-도재 고정성국소의치 파절 및 탈락과 전반적인 치료를 주소로 내원하였다. 임상 검사, 방사선 검사, 모형분석을 통해 임플란트 식립을 동반한 완전구강회복술을 하기로 결정하였다. Gothic Arch device (Centrofix; AmannGirrbach GmbH, Germany)를 이용하여 악간관계를 채득하고 마운팅 후, Shilla system을 이용하여 기존 교합평면을 평가, 분석하여 진단 납형을 제작하였다. 이를 토대로 방사선 스텐트를 제작하여 임플란트 식립하였고, 진단 납형을 이용하여 임시수복물을 제작하였다. 임시 수복물의 형태 및 교합 양식을 재현하기 위해 맞춤 전방유도판을 제작하고, 교차 마운팅을 시행하였으며 최종 수복물은 지르코니아 코핑을 이용한 완전 도재관으로 제작하였다. 이상과 같이 전악수복환자에서 진단과 치료 과정에서 Shilla system을 이용하여 적절한 심미적, 기능적 수복 결과를 얻을 수 있었다.
본 논문은 상하 회전형 차동 구동부를 이용한 자기 유도 무인운반차에 대한 연구이다. 기존의 자기 유도 무인운반차는 주행 정보를 얻기 위해 자기 위치측정 센서 외에 랜드마크 및 이를 인식하기 위한 추가적인 센서가 필요하다. 또한, 일반적으로 사용되는 고정형 차동 구동부를 사용할 경우 자기 유도 무인운반차의 무게 불균형으로 인해 위치측정 오차의 증가 및 제어에 어려움이 존재하므로 2개 이상의 구동부를 필요로 한다. 이러한 단점들을 해결하기 위해 본 논문에서는 상하 회전형 차동 구동부를 이용한 자기 유도 무인운반차를 제안한다. 제안된 무인운반차는 주행 경로상에 자석의 양극으로 패턴을 구성하고 자기 위치측정 센서로 주행 정보를 획득하며, 하나의 상하 회전형 차동 구동부를 이용하여 후진 주행을 제어한다. 또한, 위치측정 오차의 감소를 위해 KF(Kalman filter)를 적용하여 무인운반차의 위치측정 정밀도를 향상시킨다. 제안된 방법의 성능을 확인하기 위하여 직접 제작한 자기 유도 무인운반차를 이용하여 실험하였다. 실험 결과, 제안된 방법의 패턴 인식 및 무인운반차의 후진 주행 성능을 확인할 수 있었으며, 기존의 방법보다 위치측정 정밀도의 RMSE가 더 감소된 것을 확인하였다.
에너지 절감형 서버 클러스터에서는 에너지 절감을 고려하지 않는 기존 서버 클러스터에 비해 서비스 품질을 보장하면서 전력소비를 절감하는 것을 목표로 하며, 현재의 부하를 처리하는 데 필요한 최소수의 서버들만 ON 하도록 고정 주기 또는 가변 주기로 서버들의 전원모드를 조정한다. 이에 대한 기존 연구들은 전력을 절감하거나 열을 낮추는데 노력해왔지만 에너지 효율성을 잘 고려하지 못했다. 본 논문에서는 기존 자율학습기반의 서버 전원 모드 제어 방법의 단위전력당 성능과 QoS를 높이기 위한 에너지 효율적인 클러스터 관리기법을 제안한다. 제안 방법은 다중임계기반의 자율학습 방법과 전력소모 예측 방법을 결합한 서버 전원 모드 제어이다. 일반적인 부하 상황에서는 다중임계 학습기반의 서버 전원 모드 제어를 적용하고, 급변하는 부하 상황에서는 예측기반의 서버 전원 모드 제어가 적용된다. 일반적 상황과 급변하는 상황의 구별은 현재의 사용자 요청과 관찰된 과거 몇 분의 사용자 요청의 비율에 따라 이루어진다. 또한, 동적종료 기법을 추가로 적용해 서버가 OFF 하는 데 소요되는 시간을 단축한다. 제안 방법은 16대 서버로 구성된 클러스터 환경에서 3가지 부하 패턴을 이용하여 실험을 수행한다. 다중임계 학습, 예측, 동적종료를 함께 이용한 실험에서 단위전력당 성능(유효응답 수)과 표준화된 QoS 측면에서 가장 우수한 결과를 보여준다. 제안하는 방법과 파라미터 로드된 단일임계 학습을 비교할 때 뱅킹 부하패턴, 실제 부하패턴, 가상 부하패턴에서 단위전력당 유효응답 수가 각각 1.66%, 2.9%, 3.84% 향상되고, QoS 관점에서는 각각 0.45%, 1.33%, 8.82% 향상되었다.
Prihambodo, Tri Rachmanto;Sholikin, Muhammad Miftakhus;Qomariyah, Novia;Jayanegara, Anuraga;Batubara, Irmanida;Utomo, Desianto Budi;Nahrowi, Nahrowi
Animal Bioscience
/
제34권3_spc호
/
pp.434-442
/
2021
Objective: This study aims to evaluate the influence of dietary flavonoids on the growth performance, blood and intestinal profiles, and carcass characteristics of broilers by employing a meta-analysis method. Methods: A database was built from published studies which have reported on the addition of various levels of flavonoids from herbs into broiler diets and then monitored growth performance, blood constituents, carcass proportion and small intestinal morphology. A total of 42 articles were integrated into the database. Several forms of flavonoids in herbs were applied in the form of unextracted and crude extracts. The database compiled was statistically analyzed using mixed model methodology. Different studies were considered as random effects, and the doses of flavonoids were treated as fixed effects. The model statistics used were the p-values and the Akaike information criterion. The significance of an effect was stated when its p-value was <0.05. Results: Dietary flavonoids increased (quadratic pattern; p<0.05) the average daily gain of broilers in the finisher phase. There was a reduction (p<0.01) in the feed conversion ratio of the broilers both in the starter (linear pattern) and finisher phases (quadratic pattern). The mortality rate tended to decrease linearly (p<0.1) with the addition of flavonoids, while the carcass parameter was generally not influenced. A reduction (p<0.001) in cholesterol and malondialdehyde concentrations (both linearly) was observed, while super oxide dismutase activity increased linearly (p<0.001). Increasing the dose of flavonoids increased (p<0.01) the villus height (VH) and villus height and crypt depth (VH:CD) ratio (p<0.05) in the duodenum. Similarly, the VH:CD ratio was elevated (p<0.001) in the jejunum following flavonoid supplementation. Conclusion: Increasing levels of flavonoids in broilers diet leads to an improvement in growth performance, blood constituents, carcass composition and small intestinal morphology.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.