• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.251-252
• /
• 2011

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.252-257
• /
• 2000

An efficient method is developed for mold thermal cycle analysis in repeated forming process, which is well suited to the analysis in TV glass production. plunger, which is a mold to press-form the glass, undergoes temperature fluctuation during a cycle due to the repeated contact and separation from the glass, which attains a cyclic steady state in the end. If analyzed straightforwardly of this problem, it leads to more than 80 cycles to get reasonable solution, and it is yet hard to setup stopping creteria due to extremely slow convergence. An exponential fitting method is proposed to solve the problem, where an exponential function is found to best approximate temperature values of 3 consecutive cycles, and new cycle is restarted with the function value at infinite time. From numerical implementation, it is found that the method reduces the number of cycles dramatically to only $6{\sim}15$ cycles to reach accurate solution within $1^{\circ}$ error. A system for the analysis is contructed, in which the thermal analysis is performed by commercial software ANSYS, and the fitting of the result is done by IMSL library.

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.140-145
• /
• 2015

In the present study, the structural safety of the bolt portion and collet tool structure of the pipe-fitting tool is analyzed by using the finite element technique. Two forces as piston forces with the magnitude of 187.5 Tons are applied to the inner and outer portions of the collet tool, respectively. A structural load of 750 Tons is applied to the bolt portion. In the analysis results, it is found that the structure becomes safe under the current loading conditions. The reliability rating of the pipe is calculated in this study. The material properties of the actual material are evaluated by using mechanical testing. Therefore, the material properties are used to carry out static structural and optimization analysis.

• 전기학회논문지
• /
• 제63권8호
• /
• pp.1098-1103
• /
• 2014

This study deals with the development of an electrofusion welding machine that is capable of joining plastic pipes using a recently developed electrofusion fitting. This fitting has built-in conductive plastics that are used to weld the joint together as a heating element. In order to explain the mechanism of the new machine, 1) the resistance characteristics of the heating element were explained, 2) the method of electric welding that uses the electrofusion fitting was described, and 3) the method of power supply based on controlling the firing angle was explained. A control system for an intelligent electrofusion welding machine was proposed. This system has the ability to recognize the diameter of an electrofusion fitting using a lookup-table based on the difference of resistance curves according to fitting types, and it is able to weld the fittings regardless of the ambient temperature. A new algorithm was developed to control the power of electric welding through the recognition of feature points from the resistance curve of the heating element. In order to evaluate the performance of the developed welding machine, tests involving the welding of 16 mm- and 20 mm-type fittings were carried out. Examining the welding results, we concluded that the proposed welding machine will offer high productivity and reliability in the field of electrofusion welding.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.390-391
• /
• 2009

Recently, composite hollow bushings have been increasingly employed mainly from the various characteristics. Composite bushings are superior to porcelain bushings in several respects, including lighter weight, better anti-pollution and anti-explosion properties, and easer manufacturing. This paper deals with the optimal thermal fitting for improved tightness characteristics of composite bushing. Two types of composite bushings were fabricated. For optimal fitting process, it is necessary using adhesive and designed internal structure of flange and FRP tube. In this study, for improved tightness characteristics of composite bushing has prominence and interface tolerance of flange and FRP tube. From FE-SEM analysis the adhesive layers were different with interface tolerance, sample 1 and 2 which have respective about $120{\mu}m$ and $50{\mu}m$.

• 한국공작기계학회논문집
• /
• 제12권2호
• /
• pp.79-85
• /
• 2003

An algorithm for fitting with Least Square is a traditional and an effective method in processing with experimental data. Due to the lack of definite representation, it is difficult to fit measured data with free curves or surfaces. B-Spline is usefully utilized to express free curves and surfaces with a few parameters. This paper presents the combination of these two techniques to process the point data measured from CMM and other similar instruments. This research shows tests and comparison of the simulation results from two techniques.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.235-238
• /
• 2001

Deformation phase can be obtained by using Least-Square Fitting. In extraction of phase values, Least-Square Fitting is superior to usual method like as 2, 3, 4-Bucket Algorithm. That can extract almost noise-free phase and retain 2$\pi$discontinuities. But more fringe in phase map, 2$\pi$ discontinuities is destroyed when that is filtered and reconstruction of deformation is not reliable. So, we adapted Least-Square Fitting using an isotropic window in dense fringe. using Sine-Cosine filter give us perfect 2$\pi$discontinuities information. We showed the process and result of extraction of phase map and filtering in this paper.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.20-26
• /
• 2002

Deformation phase can be obtained by using Least-Square fitting. In extraction of phase values, Least-Square Fitting is superior to usual method such as 2, 3, 4-Bucket Algorithm. That can extract almost noise-free phase and retain 2 $\pi$ discontinuities. But more fringes in phase map, 2 $\pi$ discontinuities are destroyed when that are filtered and reconstruction of deformation is not reliable. So, we adapted Least-Square fitting using an isotropic window in dense fringe. Using Sine/cosine filter give us perfect 2 $\pi$ discontinuities information. We showed the process and result of extraction of phase map and filtering in this paper.

• 한국CDE학회논문집
• /
• 제4권1호
• /
• pp.32-42
• /
• 1999

Approximate lofting or skinning is one of practical surface modeling techniques well used in CAD and reverse engineering applications. Presented in this paper is a method for approximately lofting a given set of curves wihin a specified tolereance. It is based on refitting input curves simultaneously on a common knot vector and interpolating them to get a resultant NURBS surface. A concept of reducing the number of interior knots of the common knot vector is well adopted to acquire more compact representation for the resultant surface. Energy minimization is newly introduced in curve refitting process to stabilize the solution of the fitting problem and get more fair curve. The proposed approximate lofting provides more smooth surface models and realizes more efficient data reduction expecially when the parameterization and compatibility of input curves are not good enough. The method has been successfully implemented in a new CAD/CAM product VX Vision? of Varimetrix Corporation.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.107-108
• /
• 2020

The severity of the global climate crisis is increasing due to greenhouse gases caused by human activities. As a result, countries and industries are making efforts to reduce carbon dioxide emissions, the biggest cause of global warming. Many studies have been conducted to predict carbon emissions in the construction sector to reduce this, but they have not actually produced a highly usable formula in the field. Therefore, the two variables 'Curve Fitting' were performed based on the data of excavators and trucks measured at the field. As a result, we have obtained a carbon dioxide emission prediction model for construction equipment, and we would like to use it to help establish an eco-friendly process plan.