• Computers and Concrete
• /
• v.21 no.2
• /
• pp.127-137
• /
• 2018

In this study, the behavior of the number of anchorage bolts on the glass-fiber reinforced polymer (GFRP) plates adhered to the surfaces of reinforcing concrete (RC) T-beams was investigated analytically. The analytical results were compared to the test results in term of shear strength, and midpoint displacement of the beam. The modelling of the beams was conducted in ABAQUS/CAE finite element software. The Concrete Damaged Plasticity (CDP) model was used for concrete material modeling, and Classical Metal Plasticity (CMP) model was used for reinforcement material modelling. Model-1 was the reference specimen with enough sufficient shear reinforcement, and Model-2 was the reference specimen having low shear reinforcement. Model-3, Model-4 and Model-5 were the specimens with lower shear reinforcement. These models consist of a single variable which was the number of anchorage bolts implemented to the GFRP plates. The anchorage bolts of 2, 3, and 4 were mutually mounted on each GFRP plates through the beam surfaces for Model-3, Model-4, and Model-5, respectively. It was found that Model-1, Model-3, Model-4 and Model-5 provided results approximately equal to the test results. The results show that the shear strength of the beams increased with increasing of anchorage numbers. While close results were obtained for Model-1, Model-3, Model-4 and Model-5, in Model-2, the rate of increase of displacement was higher than the increase of load rate. It was seen, finite element based ABAQUS program is inadequate in the modeling of the reinforced concrete specimens under shear force.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.466-471
• /
• 2008

Structural vibration and noise are hot issues in underwater vehicles such as submarines for their survivability. Therefore, active vibration and noise control of submarine, which can be modeled as hull structure, have been conducted by the use of piezoelectric materials. Traditional piezoelectric materials are too brittle and not suitable to curved geometry such as hull structures. Therefore, advanced anisotropic piezoceramic actuator named as Macro-Fiber Composite (MFC), which can provide great flexibility, large induced strain and directional actuating force is adopted for this research. In this study, dynamic model of the smart hull structure is established and active vibration control performance of the smart hull structure is evaluated using optimally placed MFC. Actuating performance of MFC is evaluated by finite element analysis and dynamic modeling of the smart hull structure is derived by finite element method considering underwater condition. In order to suppress the vibration of hull structure, Linear-Quadratic-Gaussian (LQG) algorithm is adopted. After then active vibration control performance of the proposed smart hull structure is evaluated with computer simulation and experimental investigation in underwater. Structural vibration of the hull structure is decreased effectively by applying proper control voltages to the MFC actuators.

• Structural Engineering and Mechanics
• /
• v.48 no.5
• /
• pp.737-755
• /
• 2013

This paper aims to develop a practical approach to modeling of fiber reinforced polymers (FRP) strengthened masonry panels. The main objective is to provide suitable relations for the material characterization of the masonry constituents so that the finite element applications of elasto-plastic theory achieves a close fit to the experimental load-displacement diagrams of the walls subjected to in-plane shear and compression. Two relations proposed for masonry columns confined with FRP are adjusted for the cohesion and the internal friction angle of both units and mortar. Relating the mechanical parameters to the uniaxial compression strength and the hydrostatic pressure acting over the wall surface, the effects of major and intermediate principal stresses ${\sigma}_1$ and ${\sigma}_2$ on the yielding and the shape of the deviatoric section are then reflected into the analyses. Performing nonlinear finite element analyses (NLFEA) for the three walls tested in two different studies, their stress-strain response and failure modes are eventually evaluated through the comparisons with the experimental behavior.

• Computers and Concrete
• /
• v.26 no.2
• /
• pp.107-114
• /
• 2020

In this study, a two dimensional model of receding contact problem has been analyzed using finite element method (FEM) based software ANSYS and ABAQUS. For this aim finite element modeling of elastic layer and two homogeneous, isotropic and symmetrical elastic quarter planes pressed by means of a rigid circular punch has been presented. Mass forces and friction are neglected in the solution. Since the problem is examined for the plane state, the thickness along the z-axis direction is taken as a unit. In order to check the accuracy of the present models, the obtained results are compared with the available results of the open literature as well as the results of two software are compared using Root Mean Square Error (RMSE) and good agreements are found. Numerical analyses are performed considering different values of the external load, rigid circular radius, quarter planes span length and material properties. The contact lengths and contact stresses of these values are examined, and their results are presented. Consequently, it is concluded that the considered non-dimensional quantities have noteworthy influence on the contact lengths and contact stress distributions, additionally if FEM analysis is used correctly, it can be an efficient alternative method to the analytical solutions that need time.

• Structural Engineering and Mechanics
• /
• v.61 no.6
• /
• pp.693-700
• /
• 2017

Concrete cover cracking due to the corrosion of steel reinforcing bars is one of the main causes of deterioration in Reinforced Concrete (RC) structures. The oxidation level of the bars causes varying levels of expansion. The rebar expansions could lead to through-thickness cracking of the concrete cover, where depending on the cracking characteristics, the service life of the structures would be affected. In this paper, the effect of geometrical and material parameters, i.e., concrete cover thickness, reinforcing bar diameter, and concrete tensile strength, on the required pressure for concrete cover cracking due to corrosion has been investigated through detailed numerical simulations. ABAQUS finite element software is employed as a modeling platform where the concrete cracking is simulated by means of eXtended Finite Element Method (XFEM). The accuracy of the numerical simulations is verified by comparing the numerical results with experimental data obtained from the literature. Using a previously proposed empirical equation and the numerical model, the time from corrosion initiation to the cover cracking is predicted and then compared to the respective experimental data. Finally, a parametric study is undertaken to determine the optimum ratio of the rebar diameter to the reinforcing bars spacing in order to avoid concrete cover delamination.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2001.10a
• /
• pp.215-219
• /
• 2001

The resonators made of piezoelectric crystals such as a quartz crystal are widely used. Their frequency-temperature characteristics are of primary importance for their applications to the frequency control devices. The characteristics estimation is useful for determining their design parameters. In the present paper, several types of resonators are numerically analyzed. The numerical solutions are made using 3-D Finite Element Modeling, and the results are compared with the theoretical values whenever they are available. To demonstrate the validity of the present numerical approach, the application is made to the analysis of the plates with some well-established cutting angles. For the resonator stable with temperature change, the cutting angle is important in which the temperature coefficient of the first order is chosen to be zero. The rotated Y-cut plates in thickness-shear mode are considered. The equivalent circuit representation is often used fur describing the characteristics at the electrical terminals which enables the circuit analysis including the effect of temperature change by using the circuit simulators. The equivalent circuit parameters are obtained by fitting the admittance-frequency curve from the finite element analysis.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1234-1239
• /
• 2003

In the product design process computer-aided engineering and optimization tools are widely utilized in order to reduce the total development time and cost. Since several simulation tools are involved in the process, information losses, omissions, or errors are common and the importance of seamless information exchange among the tools has been increased. In this study ISO STEP standards are adopted to represent the neutral format for CAE/CAO information exchange. The schema of AP209 is used to define the information of finite element analysis and the new schema is proposed to describe the information of structural optimization based on the STEP methodology. The schema is implemented by EXPRESS, information modeling language, and ST-Developer is employed to generate C++ classes and STEP Rose Library by using the schema denoted. To substantiate the proposed approach, the information access interfaces of the finite element modeling software (FEMAP), structural optimization software (GENESIS) and in-house topology optimization program are developed. Examples of the size optimization of a three-bar truss and topology optimization of a MBB beam are shown to validate the information exchange of finite element analysis and structural optimization using STEP standards.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.204-207
• /
• 2005

A reliable and practical finite element modeling technique to predict the lifetime of automotive electronics is important for engineers in reliability. In reliability evaluation on the automotive electronics, most studies rarely used FE model verification process. The material properties and boundary conditions are very important factors in this process to assure the reliability of the automotive electronics. This study aims to develop a better and more accurate FE model in order to predict fatigue life of the automotive electronics using Virtual Qualification lifetime assessment techniques. After conducting the modal analysis by the experiments to grasp a system characteristic, this paper presents material properties and boundary conditions that is obtained by the comparisons of FEA simulation results using DOE technique and the experiment results.

• Structural Engineering and Mechanics
• /
• v.50 no.6
• /
• pp.835-852
• /
• 2014

Despite the availability of other transport methods such as land and air transportations, marine transportation is the most preferred and widely used transportation method in the world because of its economical advantages. In service, ships experience cyclic loading. Hence, it can be said that fatigue fracture, which occurs due to cyclic loading, is one of the most critical failure modes for vessels. Accordingly, this makes fatigue failure prevention an important design requirement in naval architecture. In general, a ship structure contains many structural components. Because of this, structural modeling typically relies on Finite Element Analysis (FEA) techniques. It is possible to increase fatigue performance of the ship structures by using FEA in computer aided engineering environment. Even if literature papers as well as rules of classification societies are available to assess effect of fatigue cracks onto the whole ship structure, analytical studies are relatively scarce because of the difficulties of modeling the whole structure and obtaining reliable fatigue life predictions. As a consequence, the objective of this study is to improve fatigue strength of a mercantile vessel against fatigue loads via analytical method. For this purpose, the fatigue life of the mercantile vessel has been investigated. Two different type of fatigue assessment models, namely Coffin-Manson and Morrow Mean stress approaches, were used and the results were compared. In order to accurately determine the fatigue life of the ship, a nonlinear finite element analysis was conducted considering plastic deformations and residual stresses. The results of this study will provide the designer with some guidelines in designing mercantile vessels.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.876-881
• /
• 2004

Finite element model updating is an inverse problem to identify and correct uncertain modeling parameters that leads to better predictions of the dynamic behavior of a target structure. Unlike other inverse problems, the restrictions on selecting parameters all: very high since the updated model should maintains its physical meaning. That is, only the regions with modeling errors should be parameterized. And the variations of the parameters should be kept small while the updated results give acceptable correlations with experimental data. To avoid an ill-conditioned numerical problem, the number of parameters should be kept as small as possible. Thus it is very difficult to select an adequate set of updating parameters which meet all these requirements. In this paper, the importance of updating parameter selection is illustrated through a case study, and an automated procedure to guide the parameter selection is suggested based on simple observations. The effectiveness of the suggested procedure is tested with two example problems, ones is a simulated case study and the other is a real engineering structure.