• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.469-475
• /
• 2014

This paper deals with the characteristics evaluations of PM magnetization using stator coil in a Post-Assembly Line Start Permanent Magnet Motor (LSPMM) using a coupled Finite Element Method (FEM) and Preisach modeling, which is presented to analyze the magnetic characteristics of permanent magnets. The focus of this paper is the characteristics analysis relative to magnetizing direction and quantity of permanent magnets due to the eddy current occurring in the rotor bar during magnetization of Nd-Fe-B.

• East Asian mathematical journal
• /
• v.34 no.5
• /
• pp.661-681
• /
• 2018

In this paper, we discuss a reduced-order modeling for the Benjamin-Bona-Mahony-Burgers (BBMB) equation and its application to a distributed feedback control problem through the centroidal Voronoi tessellation (CVT). Spatial distcritization to the BBMB equation is based on the finite element method (FEM) using B-spline functions. To determine the basis elements for the approximating subspaces, we elucidate the CVT approaches to reduced-order bases with snapshots. For the purpose of comparison, a brief review of the proper orthogonal decomposition (POD) is provided and some numerical experiments implemented including full-order approximation, CVT based model, and POD based model. In the end, we apply CVT reduced-order modeling technique to a feedback control problem for the BBMB equation.

• Journal of Magnetics
• /
• v.15 no.2
• /
• pp.85-90
• /
• 2010

This paper deals with the efficiency evaluations in a synchronous reluctance motor (SynRM) versus a permanent magnet assisted SynRM (PMASynRM), using a coupled transient finite element method (FEM) and Preisach modeling, which is presented to analyze the characteristics under the effects of saturation and hysteresis loss. We herein focus on the efficiency evaluation relative to hysteresis loss and copper loss on the basis of load conditions in a SynRM and PMASynRM. Computer simulation and experimental results for the efficiency, using a dynamometer, show the propriety of the proposed method and the high performance of the PMASynRM.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.172-176
• /
• 2013

Microelectromechanical system switches are becoming more and more popular in the electronics industry; there is a need for careful selection of the materials in the design and fabrication of switches for reliability and performance issues. The membrane used for actuation to change the state of an RF switch is made mostly using gold or aluminum. Various designs of membranes have been proposed. Due to the flexure-type structures, the design complexity increases, which makes stress analysis mandatory to validate the reliability and performance of a switch. In this paper, the effective stress and actuation voltage required for different types of fixed-fixed membranes is analyzed using finite element modeling. Effective measures are presented to reduce the stress and voltage.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.1-15
• /
• 1998

Currently, computational analysis is a popular technology in automobile engineering. Finite element analysis is an excellent method for body analysis. For finite element analysis, accurate modeling is very important to obtain precise information. Stick modeling is a convenient way in that it is easy and simple. When a stick model is utilized, the joints are modified in the tuning process. A tuning method for the joint has been developed. The joints are modeled by designated beam elements. An optimization method called "Goal Programming" is employed to impose the target values. With the tuned joints, the entire optimization has been carried out. Using the "Recursive Quadratic Programming" algorithm, the optimization process determines the configuration of the entire structure and sizes of all the sections. For example, the structure of an electrical vehicle is modeled and analyzed by the method. The stick model works well since the structure is made of aluminium frames. Although the example handles an electrical vehicle, this method can be applied to general vehicle structures.

• Structural Engineering and Mechanics
• /
• v.18 no.5
• /
• pp.691-707
• /
• 2004

This paper presents the micro-mechanical modeling for predicting concrete behavior under compressive loading. The model is able to represent the heterogeneities in the microstructure up to three phases, i.e., aggregate particles, matrix and interfaces. The smeared crack concept based on non-linear fracture mechanics is implemented in order to formulate the constitutive relation for each component. The splitting tensile strength is considered as a fracture criterion for cracking in micro-level. The finite element method is employed to simulate the model based on plane stress condition by using quadratic triangular elements. The validation of the model is verified by comparing with the experimental results. The influence of tensile strength from both aggregate and matrix phases on the concrete compressive strength is demonstrated. In addition, a guideline on selecting appropriate tensile strength for each phase to obtain specified concrete compressive strength is also presented.

• Structural Engineering and Mechanics
• /
• v.57 no.3
• /
• pp.425-439
• /
• 2016

This paper deals with the behavior of fresh concrete that is under vibration using mass-spring model (MSM). To this end, behaviors of two different full scale precast concrete molds were investigated experimentally and theoretically. Experiments were performed under vibration with the use of a computer-based data acquisition system. Transducers were used to measure time-dependent lateral displacements at some points on mold while mold is empty and full of fresh concrete. Analytical modeling of molds used in experiments were prepared by three dimensional finite element method (3D FEM) using software. Modeling of full mold, using MSM, was made to solve the problem of dynamic interaction between fresh concrete and mold. Numerical displacement histories obtained from time history analysis were compared with experimental results. The comparisons show that the measured and computed results are compatible.

• Journal of Power System Engineering
• /
• v.5 no.4
• /
• pp.53-60
• /
• 2001

This paper considers a modeling for the MIMO magnetic bearing system. The rotor is flexible and has a complex shape. To obtain the nominal plant transfer functions, we perform a numerical analysis by using the finite element method(F.E.M.) for the rotor's dynamics, and make a nominal model by reducing the modes from the results. And, we have experimented on the frequency response by a closed-loop identification method, and compared it with the simulation's result on the closed-loop control system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.227-232
• /
• 1995

This paper presents a digital modeling technique for the distributed parameter system. The basic idea of the proposed technique is to discretize a continuous system with respect to the spatial coordinate using the approximate methods such as bilinear method and backward difference method. The response of the discretized system is analyzed by Laplace transform and Z transform. The computational result of the proposed technique in a torsional shaft is compared with the exact solution and the result of the finite element method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.607-613
• /
• 2011

In this study, structural vibration analyses for a 5MW offshore wind wind-turbine model have been performed for different substructure models. The efficient equivalent modeling method based on computational multi-body dynamics are applied to the finite element models of the present offshore wind turbines. Monopile and tri-pod substructure types of the typical offshore wind-turbine are considered herein. Detailed finite element modeling concepts and boundary conditions are described and the comparison results for previous analyses are presented in order to show the verification of the present numerical approach. Campbell diagrams are also present to investigate the rotational resonance characteristics of the offshore wind-turbines with different substructures.