• Geomechanics and Engineering
• /
• v.31 no.6
• /
• pp.557-571
• /
• 2022

Landslides are often triggered by weak interlayers initiated in tailings dam foundations, and hazards gradually occur. This is serious for landslides in high tailings dams due to their high potential energy. Tailing samples with a fine-grained interlayer at a set dip angle were prepared. Consolidated undrained (CU) triaxial shear tests were carried out by using a high-pressure triaxial apparatus. The results were compared with the results under a low confining pressure. Four reasons were summarized for high tailings dams more prone to instability than low dams. The shear strength of the samples with dipping interlayers decreases with increasing dip angle. An obvious straight drop in the stress path after the peak occurs in samples with dipping interlayers at an angle of 60°. The effect of the interlayer on the mechanical behaviour of tailings is very sensitive, especially for the sample with a dipping interlayer at an angle of 60°. Shear slipping along the interlayer should be given more attention in tailings dams. Compared with the results under low confining pressure, the stress decreases continuously for the samples with dipping interlayers at large angles under high confining pressure. The positive pore pressure, which reduces the effective stress, occurred in tailings samples under high confining pressure. The residual strength of tailings under high confining pressure is smaller than that under low confining pressure. These factors increase the dam break risk and the disaster impact for high tailings dams.

• Journal of the Mineralogical Society of Korea
• /
• v.5 no.2
• /
• pp.102-108
• /
• 1992

The natural (Ca, Mg)-buserite has been identified from the manganese oxideores of the Janggun mine, Korea, which have been formed by supergene weathering of sedimentary-metamorphic rhodochrosite. It occurs together with rancieite forming one very fine-grained buserite-rancieite flake. This (Ca, Mg)-buserite-rancieite occurs as microcystalline flaky crystals. It precipitated around the fine-grained takanelite aggregate. Electron microprobe analyses give the formula ($Ca_{.08}Mg_{.07}Mn_{.05}^{2+})Mn_{.89}^{4+}O_2{\cdot}1.46H_2O$ for (Ca, Mg)-buserite. The dehydration experiments by relative humidity control and heating as well as rehydration experiment by relative humidity control show that (Ca, Mg)-buserite dehydrates completely at 90$^{\circ}C$ and rehydrates up to 27% of the original state. The dehydration at 26% RH (corresponding to heating to about 40$^{\circ}C$) is characterized by thedecrease in the decrease in the intensity of 9.86${\AA}$ peak with slight shifting to 9.60${\AA}$. It is due to the loss of weakly bound water molecules in the interlayer. The dehydration from 40$^{\circ}C$ to 90$^{\circ}C$ is characterized by the gradual shifting of 001 peak from 9.6${\AA}$ to 7.42${\AA}$. It is due to the loss of weakly bound water molecules in the interlayer.

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.176-176
• /
• 2000

Recently developed Austenite stainless steel,309L was to overlay on 3Cr-1Mo-V-Ti-B steels, using Electroslag welding process, which wide electrodes were adopted. Transition region in welding interlayer relating to disbonding crack was investigated. Also. the effect of welding condition on the width of transition region and coarsening grains of the austenite were studied.1) With increasing welding speed the width of martensite at transient region was increased, but the amount of delta ferrite in weld metal was reduced, being fine grained.2) The form of martensite at the transition region was occured by reversible transition region, leading to increasing Ms point.3) With increasing welding speed, the grain of austenite formed at the welding interface was finer. With increasing welding current under the same welding speed, the grain size of the austenite was finer. At high current, original grain size of the austenite is coarse, but the austenite has fine grains because the austenite was transformed to martensite during cooling.4) In the case of high welding speed, the width of martensite at the welding interface was increased, but the grain size of austenite at the welding interface was finer. This indicates that the inhibition of disbonding crack may be achieved through dispersening fine carbides in the grain boudary.(Received August 3, 1999)

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.49-56
• /
• 2000

Recently developed Austenite stainless steel, 309L was used to overlay on 3Cr-1Mo-V-Ti-B steels, using Electroslag welding process, which wide electrodes were adopted. Transition region in welding interlayer relating to disbonding crack was investigated. Also, the effect of welding condition on the width of transition region and coarsening grains of the austenite were studied. 1) With increasing welding speed the width of martensite at transient region was increased, but the amount of delta ferrite in weld metal was reduced, being fine grained. 2) The form of martensite at the transition region was occurred by reversible transformation during cooling since the interdiffusion of Cr and Ni from weld metal and Fe and C from base metals at the transition region, causes to lowering the concentration of Cr and Ni at the transition region, leading to increasing Ms point. 3) With increasing welding speed, the grain of austenite formed at the welding interface was finer. With increasing welding current under the same welding speed, the grain size of the austenite was finer. At high current, original grain size of the austenite is coarse, but the austenite has fine grains because the austenite was transformed to martensite during cooling. 4) In the case of high welding speed, the width of martensite at the welding interface was increased, but the grain size of austenite at the welding interface was finer. This indicates that the inhibition of disbonding crack may be achieved through dispersening fine carbides in the gain boundary.