• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.122-132
• /
• 2001

Thermoplastic film infusion process was investigated by using a rubber tool, which intrinsically contains a thermally-expandable characteristic and effectively compensates for the pressure loss caused by thermoplastic polymer infusion. Increasing temperature up to the melting temperature of matrix, the polymer melt subsequently infused into the dry fabric, but the pressure was successfully sustained by the rubber tool. Even with the decreased resin volume, the rubber tool produced sufficiently high elastic force for continuous resin infusion. Combining D'Arcy's law with the compressibility of rubber tool and elastic fiber bed, a film infusion model was developed to predict the resin infusion rate and pressure change as a function of time. In addition, the film infusion process without the rubber tool was viewed and analyzed by a compression process of the elastic fiber bed and viscous resin melt. The compressibility of fiber bed was experimentally measured and the multiple-step resin infusion was well described by the developed model equations.

• Composites Research
• /
• v.32 no.1
• /
• pp.45-49
• /
• 2019

Fiber reinforced composites fabricated by the resin film infusion (RFI) process, which is one of the outof-autoclave process, have the advantage of significantly reducing the processing cost in large structures while having excellent mechanical properties and uniform impregnation of the resin. In this study, we applied RFI carbon fiber composites to unmanned aerial vehicle structures to improve structural safety and achieve weight reduction. The tensile test results showed that the strength was 46% higher than that of generic T300 grade plain weave carbon fiber composites. As a result of the layup design and finite element analysis of the composite wing structure using the above material properties, the wing tip deflection is decreased by 31%, the structural safety factor is increased by 28% and the weight of the entire structure can be reduced by more than 10% compared to the reference model using glass fiber composite material.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.17 no.1
• /
• pp.123-135
• /
• 1987

The author observed the effects of retrograde infusion of water soluble contrast media (Tele- brix 30) on the rabbit submandibular glands and compared the effects of different degrees of filling. 26 rabbits were divided into 2 groups of 12 each as experimentals and I group of 2 as normal controls. One experimental group was filled with 0.2㎖ and the other with 0.4㎖. Right submandibular gland of each rabbit was infused with contrast media and left one with physiologic saline as a experimental control, at a constant rate of 0.12㎖/min. using an infusion pump via the main excretory duct. Immediately after the infusion of contrast media, oblique lateral radiographs of the glands were made with occlusal film in order to confirm the glandular filling. The rabbits were sacrificed after varying periods (1, 8, 24 hours and 3, 6, 10 days) and the tissues were prepared for light and electron microscopic examination. The results were as follows: 1. In glands filled with 0.2㎖ contrast media, the initial changes were a few vacuole formation in the acini and slight dilation of the intralobular duct. The moderately severe changes such as vacuole formation in the acini, the abnormal substructure within the secretory granule, dilation of acinar and intercalated duct lumen, scalloping of striated duct lumen and inflammatory cell infiltrate were observed at 3 days. The general appearance was successively recovered, so the tissue had a normal appearance at 10 days. 2. In glands filled with 0.4㎖ contrast media, the most prominent alterations such as severe acinar atrophy, decreased number of secretory granules, proliferation of connective tissue stroma and pronounced inflammatory cell infiltrates appeared at 6 days. Although the general appearance returned to be almost normal at 10 days, acinar cells showed some atrophy and decreased secretory granules. 3. In glands subjected to 0.4㎖ infusion, the alterations were more severe and the recovery was slower than those seen in the glands to 0.2㎖ infusion.

• Composites Research
• /
• v.31 no.1
• /
• pp.23-29
• /
• 2018

The RFI process can be applied to very thick structures without limiting the resin viscosity. When the proper thickness of the resin film cannot be set, the resin film creates either the non-impregnated section or the excessive resin contents and this leads to the deterioration of mechanical properties. Therefore, this study proposed a method for setting the resin film thickness in the RFI process. The fiber compaction behavior test was proposed by setting the proper resin film thickness and the properties of composites were evaluated through short beam shear strength test, compression test and porosity measurement to verify the proposed method. The evaluation of physical properties of composites was conducted and an appropriate level of resin film thickness was found based on the results of fiber compaction behavior test.

• Proceedings of the KOSOMBE Conference
• /
• v.1995 no.11
• /
• pp.18-21
• /
• 1995

When we inject drugstuffs to a patient for a long time, it is important to control proper injection amount and flow rate. Since inproper injection amount and a flow rate would cause bad a recovery a patient, the relience of sensors which detect injection amount is an important factor for whole injection systems' performance. In this research, we've compared the suitability of three sensors for injection pump monitoring system. The three types of sensors, piezo film sensor, photo transistor made up with three transmitting photodiodes and receving photodiode, and photo array, were selected for comparing. Using suggested data processing technique and photo amy sensors, we could minimize the effect of interference, disturbance, illumanation change, and sensitivity change caused by sensor's position. According to the experiments, the photo amy showed the higher reliance than any other the three types of sensors. The developed systems could be the foundation of beginning home production of infusion pump system and available for the base model of whole monitoring and control systems.

• Macromolecular Research
• /
• v.10 no.4
• /
• pp.194-203
• /
• 2002

In resin infusion process(RIP), the fiber and the resin are in contact with each other for an impregnation step and often results in flow-induced defects such as poor fiber wetting and void formation. Resin flow characteristics in transverse direction and process modeling for woven fabric were studied, and the process modeling was applied to the manufacturing of hybrid composite materials. This study also considered the compressibility of woven fabrics in a series of compression force, and it was fitted well to an elastic model equation. Void formation was varied with the processing conditions in the stage of manufacturing composites using RIP. It was concluded from this study that proper combination of pressure build-up and dynamic heating condition makes important factor for flow-induced composite processing.

• Composites Research
• /
• v.32 no.6
• /
• pp.395-402
• /
• 2019

The RFI process is an OoA process that fiber mats and resin films are laminated and cured in a vacuum bag. In case that resin film is insufficient to fill empty space in fibers, it makes void defect in composites and this void decrease mechanical properties of the composites. For this reason, non-destructive testing is usually used to evaluate void of manufactured composites. So, in this study, a manufacturing method of standard void specimens, which are able to be used as references in non-destructive testing, was proposed by controlling resin film thickness in the RFI process. Also, a fiber compaction test was proposed as a method to set the resin film thicknesses depending on target voids of manufacturing panels. The target void panels of 0%, 2%, and 4% were made by the proposed methods, and signal attenuation depending on void was measured by non-destructive testing and image analysis. In addition, voids of specimens for tensile, in-plane, short beam and compressive tests were estimated by signal attenuation, and mechanical properties were evaluated depending on the voids.

• Korean Journal of Food Science and Technology
• /
• v.6 no.2
• /
• pp.109-115
• /
• 1974

Milssal is a polished, partially gelatinized pressed wheat grain and it is being consumed in Korea. This study was conducted to establish 2 practical means of providing needed lysine to the Korean population through fortification of Milssal. The results are summarized as follow: Lysine infusion of Milssal was significantly higher than polished wheat grain and affected by such factors as time and concentration of infusion solution. Cooking characteristics including water-uptake ratio and expanded volume were apparently better than polished wheat. After conducting the series of fortification experiments under actual manufacturing conditions. a reasonable process was chosen. In the developed process. lysine HCl solution was sprayed instead of water to the cleaned and debranned wheat grains during the regular wetting process. There was no differences in appearance and taste of Milssal before and after fortification. Fortification of the protein of Milssal with lysine has been found to bring a significant improvement in the growth rate of rats and the protein efficiency ratio. Stability remained relatively high throughout the storage period(90 days at $10{\sim}20^{\circ}C$ or 30 days at $37^{\circ}C$).

• Composites Research
• /
• v.23 no.3
• /
• pp.13-18
• /
• 2010

One of the biggest challenges in the nano-field is how to effectively disperse nano-scale particles, especially CNTs, which are strongly agglomerated by intermolecular van der Waals forces. This study suggests a new method, discharge flocking, in order to disperse nano-scale particles effectively, which combines corona discharge phenomenon and a traditional electrostatic flocking process. In order to evaluate the discharge flocking process, composite specimens were fabricated by the process and RFI(resin film infusion) process, and then the mechanical and electrical properties of the specimens were measured and compared. Moreover, the evaluation of gas discharge effect on the CNTs and epoxy was performed to compare the mechanical and electrical properties of the composite specimens including the plasma treated CNTs. The experimental results showed that the electrical and mechanical properties of the specimens fabricated by the discharge flocking process were similar to those of the RFI process. In addition, plasma treated CNTs were not affected by gas discharge during the discharge flocking process.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.65-73
• /
• 1996

One of the important factor in drug stuffs to a patient is to inject exact amount with stable flow rates. Since improper injection amount and flow rates would cause bad effect to recovery of a patient, the detecting sensors with high sensitivity is required for an injection pump systems' performance improvement. In this study, the three sensors, piezo film sensor, photo transistor and photo array, were compared to find best one for an injection pump monitoring system. Using suggested data processing technique and photo array sensors, we could minimize the effect of interference, disturbance, illumination, and sensitivity change caused by sensor's position. According to the experiments, the photo array showed the higher reliance than any other the three types of sensors.