• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.317-320
• /
• 1997

The paper reports on a study of the influence of the size of the particles of alumina trihydrate(ATH) filler on the surface aging characteristics of ehylene propylene diene terpolymer(EPDM). A fixed 100pph concentration of the filler of ATH was used (or all particle sizes from 0.7 to 20$\mu\textrm{m}$, It is show that hysteresis of contact angle and leakage current increase with increasing particle size, whereas tracking resistance decrease with increasing particle size.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.3 s.116
• /
• pp.7-12
• /
• 2006

The pore structure of paper was modified by the application of the blending of pulp, refining, and filler particle size and ash content. It was conformed that the reflectivity of paper can be modified by the combination of the above parameters. It was also found that the change of reflectivity of paper was greatly dependent on the pore structure, such as average pore size, pore size distribution and porosity. The average pore size was decreased with addition of HwBKP, but the smallest average pore size was obtained from the addition of 80% HwBKP Refining of pulp decreased both average pore size and the reflectivity of paper. The pore size distribution of filled paper can be varied by the combination of filler particle size and ash content

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.42-45
• /
• 1996

A residue from the newsprint waste was investigated as a filler in adhesive for bonding southern pine plywood. The residue was prepared by drying the wet residue to 8% moisture content and grinding the dry material using a laboratory Wiley mitt with a 75-${\mu}m$(200-mesh) screen. The residue was compared to a commercial filler commonly used in structural plywood adhesives. A total of 48 three-ply panels. 12.7mm nominal thickness and 0.3 by 0.3 m in size, were fabricated at two press times(4 and 5 min) and three assembly times(20, 40 and 60 min). Evaluations of the residue were carried out by performance tension shear tests after two 4-hour boil accelerated aging tests on plywood. The test results included tension shear strength and estimated wood failure values. All plywood made with the residue filler were comparable to the control-bonded plywood. These results indicate that residue from the newsprint waste streams would be suitable as filler for plywood adhesives.

• Archives of Metallurgy and Materials
• /
• v.65 no.4
• /
• pp.1323-1327
• /
• 2020

In this paper, we have studied the evolution of morphology and brazing behavior of Ag-28Cu alloy filler processed by high energy ball milling. The milling of the powder mixture was carried out for 40 h. The structural and morphological analyses were performed by the X-ray diffraction and scanning electron microscopy. The melting temperature of the braze filler was determined by differential thermal analysis. The filler wetting properties were assessed from the spread area ratio measurements on various Ti substrates. The results indicate that the ball milling can effectively depress the filler melting point and enhance the brazeability. The milled powder mixture showed Ag(Cu) solid solution with a crystallite size of 174-68 nm after 40 h. It was shown that the high energy ball milling can be a potential method to develop low temperature brazing fillers for advanced microjoining applications.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.479-484
• /
• 2006

The pore structures of paper were modified by the application of the blending of pulp, refining, and filler particle size and ash content. It was conformed that the reflectivity of paper can be modified by the combination of above parameters. It was also found that the modifications of reflectivity of paper were very close relation with pore structure, such as average pore size, pore size distribution and porosity. The average pore size was decreased with addition of HwBKP, but showed smaller particle size than those made from 100% HwBKP. Refining of pulp decreased both average pore size and the reflectivity of paper. The pore size distribution of filled paper can be varied by the combination of filler particle size and ash content.

• Carbon letters
• /
• v.11 no.4
• /
• pp.293-297
• /
• 2010

To investigate new potential application of a clay material for C/C composites, illite added C/C composites were prepared with various illite contents. The improvement of filler effect by illite size reduction was also investigated using wet ballmilling by evaluating illite/phenolic resin infiltration using bulk density and porosity measurements, chemical structural changes of the composites using XRD, and thermal oxidation stability in air of the composites using TGA. The size reduction of illite resulted in narrower particle size distribution and improved illite infiltration into carbon preform. And the resultant C/C composites prepared with illite had even more improved thermal oxidation stability in air, showing more increased IDTs up to $100^{\circ}C$, compared to those of the C/C composites with pristine illite, due to the SiC formation through carbothermal reduction between illite and carbon materials. The illite induced delay in oxidation of the illite-C/C composites was also observed and the delayed oxidation behavior was attributed to the layered structure of illite, which improved illite/phenol resin infiltration. Therefore, the potential use of illite as filler to improve oxidation stability of C/C composite can be promising. And the size reduction of illite can improve its effect on the desired properties of illite-C/C composites even more.

• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.93-103
• /
• 2005

In this study, surface treatment of the elastomeric matrix was investigated to develop a substituting material for steel dynamic damper of automobile. The key technology is to get ultra high density elastomeric compound in order to substitute steel dynamic damper. The optimum matrix material(chloroprene rubber) and filler(metal powder) were selected for this. The several properties of elastomeric compound were examined. According to the results, the $t_{s2}$ of filled elastomeric compound was decreased with increasing the filler loading whereas the $t_{90}$ was increased. Also, tensile strength and rebound resilience were decreased with filler loading. To solve the problem of high filler loading, the photo grafting technique was employed on elastomeric matrix. The degree of grafting was determined by FTIR-ATR. Also, the filler surface was modified by chemical etching and the surface morphology was examine by SEM. After chemical treatment of filler, the particle size analyzer was used to examined the particle size, size distribution, and morphology of the modified filler.

• Nuclear Engineering and Technology
• /
• v.53 no.12
• /
• pp.4142-4149
• /
• 2021

In the radiation protection application, the metal-polymer composites have been developed for their radiation shielding properties. In this research, the elastomer composites doped by 10 ㎛ and 100nm size of lead, bismuth and tungsten particles as filler with 30 and 60 wt percentages were prepared. To survey the shielding properties of the polymer composites using gamma-ray emitted from 152Eu and 137Cs sources, the gamma flux was measured by using NaI(Tl) detector, then the linear attenuation coefficient was calculated. Also, the Monte Carlo simulation (MCs) method was used. The results showed a direct relationship between the linear attenuation coefficients of the absorbent and filler ratio. Also, the decrease in the particle size of the shielding material in each weight percentage improved the radiation shielding features. When the dimension of the particles was in the order of nano-size, more attenuation was achieved. At low energies used for medical diagnostic X-ray applications due to the predominance of the photoelectric effect, bismuth and lead were suitable selection as filler.

• Journal of Adhesion and Interface
• /
• v.15 no.4
• /
• pp.169-173
• /
• 2014

The effect of filler sizes on the thermal diffusivity of Nylon 66/SiC composites was investigated. By loading 60 vol% of SiC fillers on Nylon 66, the thermal diffusivity of the composites increased more than 10 times than that of unfilled Nylon 66 and the thermal diffusivity of composites with filler sizes of $24{\mu}m$ and $76{\mu}m$ increased to $2.2{\times}10^{-2}cm^2/sec$ and $1.75{\times}10^{-2}cm^2/sec$, respectively. It is speculated that the smaller filler size ($24{\mu}m$) of SiC is more favorable for the formation of thermal conductive path that the larger size ($76{\mu}m$) of filler composites. The thermal diffusivity of Nylon 46/SiC 400 (60 vol%) composites was $1.61{\times}10^{-2}cm^2/sec$ that was lower than that of Nylon 66/SiC (60 vol%) composites.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.4
• /
• pp.33-38
• /
• 2010

The effects of fillers on the wet end dewatering and paper properties were investigated in order to confirm the possibility that the fillers can be used as a means for saving energy in papermaking process. The performance of GCC, PCC and talcs were evaluated. The dewatering in wire and wet press was improved by the increase of filler addition, but it was observed that the dewatering behavior was depended by the filler characteristics. PCC was superior to other fillers in the bulk, opacity, air permeability and stiffness while the lowest tensile and burst index were obtained. We found that the response on the wet end dewatering and paper properties were affected greatly by the filler characteristics including particle shape and size.