• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.673-681
• /
• 2014

In this paper, a novel low specific on-resistance SOI LDMOS Device with P+P-top layer in the drift region is proposed and investigated using a two dimensional device simulator, MEDICI. The structure is characterized by a heavily-doped $P^+$ region which is connected to the P-top layer in the drift region. The $P^+$ region can modulates the surface electric field profile, increases the drift doping concentration and reduces the sensitivity of the breakdown voltage on the geometry parameters. Compared to the conventional D-RESURF device, a 25.8% decrease in specific on-resistance and a 48.2% increase in figure of merit can be obtained in the novel device. Furthermore, the novel $P^+P$-top device also present cost efficiency due to the fact that the $P^+$ region can be fabricated together with the P-type body contact region without any additional mask.

• 한국식물병리학회:학술대회논문집
• /
• 한국식물병리학회 2003년도 정기총회 및 추계학술발표회
• /
• pp.69.2-70
• /
• 2003

For the selection and breeding of chestnut varieties resistant to the chestnut blight fungus Cryphonectria parasitica, disease resistance and susceptibility of 28 varieties widely planted and growing in Korea were evaluated by artificial inoculation of a pathogenic fungus. For this experiment, a typical virulent strain (KCPC-19) was selected. Artificial inoculation was conducted into all varieties by using two different materials and methods, i.e., bark and wood tissue sections in the laboratory and living trees in the field. In the bark and wood tissue section method, the size of necrotic area and canker development on chestnut varieties were examined and compared 4 days after inoculation. There were wide variations of chestnut varieties in disease resistance and susceptibility against chestnut blight fungus, but 3 varieties, Daebo！, Ishizuchi, and Sandae, were shown to be relatively resistant to the disease with the necrotic area of 0.95-1.03 cm2, while Arima was the most susceptible with the size of 2.0 cm2. In the living tree inoculation examined 5 weeks after inoculation, 3 varieties, Daebo, Ishizuchi, and Riheiguri, showed the higher resistance, but Tono 2 did the highest susceptibility among tested varieties.

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.129-136
• /
• 2010

The corrosion behaviors of 316L stainless steel were investigated in simulated anodic and cathodic environments for proton exchange membrane fuel cell (PEMFC) by using electrochemical measurement techniques. Interfacial contact resistance(ICR) between the stainless steel and gas diffusion layer(GDL) was also measured. The possibility of 316L was evaluated as a substitute material for the graphite bipolar plate of PEMFC. The value of ICR decreased with an increase in compaction stress(20 N/$cm^2$~220 N/$cm^2$) showing the higher values than the required value in PEMFC condition. Although 316L was spontaneously passivated in simulated cathodic environment, its passive state was unstable in simulated anodic environment. Potentiostatic and electrochemical impedance spectroscopy (EIS) measurement results showed that the corrosion resistance in cathodic condition was higher and more stable than that in anodic condition. Field emission scanning electron microscopy (FE-SEM), and inductively coupled plasma(ICP) were used to analyze the surface morphology and the metal ion concentration in electrolytes.

• 한국환경과학회지
• /
• 제7권1호
• /
• pp.36-40
• /
• 1998

This study was carried out to investigate the collection Efficiency of mass in collector step at the different of physical gas characterization. This work has focused on the dependence of the collection efficiency of mass in the collector zone of a two-stage set up field with gas temperature T and the dew point tmeperature. To identify the dependence of the mass collection efficiency on the Bounded plate of the collector zone MP.k by the spectre electric resistance of dust $p_e$. and the relative humidify ${\varphi}$, 20 at- tempts have been made with three different gas temperature ($50{\circ}C, 80{\circ}C, 110{\circ}C$) at different dew point. At the specific electric resistance of dust $p_e$=$10^6{\Omega}m$ which relative humidity corresponds to $\phi$ > 15%, a easy rise of the sounded plate secluded dust mass share was measured atwain. As the result of the higher cohesion imprisonment power due to the adsorbtion of particle, the rinse of the relative humidity developed on the particle surface. Therefore, the collection efficiency of mass was not predominant the high temperature T in the collector zone, neither was the pecific ellectric resistance of dust dependent.

• 전자공학회논문지A
• /
• 제33A권7호
• /
• pp.176-184
• /
• 1996

To overcome the drawbacks of conventional LDMOSFETs, we propose RESURF EDMOSFETs which can be adapted in varous circuit applications, be driven without charge pumping circuity and thowe threshold voltage can be adjusted. The devices have the diffused drift region formed by a high tmperature process before the gate oxidaton. After the polysilicon gate electrode formation, a fraction of the drift region around the gate edge is opened for supplemental self-aligned ion implantation to obtain self-aligned drift region. This leads to a shorter gate length and desirable drift region junction contour under the gate edge for minimum specific-on-resistance. In additon, a and maximize the breakdown voltage. Also, by biasing the metal field plate, we can reduce the specific-on-resistance further. The devices are optimized by using the TSUPREM-4 process simulator and the MEDICI device simulator. The optimized devices have the breakdwon voltage and the specific-on-resistance of 101.5V and 1.14m${\Omega}{\cdot}cm^{2}$, respectively for n-channel RESURF EDMOSFET, and 98V and 2.75m.ohm..cm$^{2}$ respectively for p-channel RESURF EDMOSFET. To check the validity of the simulations, we fabricated n-channel EDMOSFETs and confirmed the measured breakdown voltage of 97V and the specific-on-resistance of 1.28m${\Omega}{\cdot}cm^{2}$. These results are superior to those of any other reported power devices for smart power IC applications.

• 한국응용곤충학회지
• /
• 제13권2호
• /
• pp.83-88
• /
• 1974

이화명충(Chilo suppressalis Walker)에 대한 벼 품종별 저항성을 알기 위하여 통일(수원 21교, 진흥, IR747, 수원 229호 등 58개 품종을 공시하여 시험을 하였다. 실내시험에서 유충기간은 품종간 대차없었다. 유충체중은 감수성 품종에서는 34.4mg이었으나 저항성 품종은 18.0mg이었으며 용화율도 저항성 품종에서 높았다. 산난선호성 시험에서는 수원 240호 천추락 등이 낮은 선호성을 보였고 포장조사에서는 Tetep, 망게스 찰 IR747등이 낮은 피해경률을 나타내었다.

• 전기의세계
• /
• 제22권4호
• /
• pp.7-10
• /
• 1973

The characteristics of all the instruments and materials used in atomic industry is changed due to radiation damages by the effects of radiation activities. In this study, when the Carbon Resistor, main element of electrical circuits, is irradiated by Gamma-Ray, variations in its electrical properties have been investigated. The following results are obtained: 1) The resistance value in Carbon Resistor is exponentially increased as the quantity of irradiation by Gamma-Ray is increased, but in case of more than 10$^{6}$ R/hr. of quantity of irradiation it has saturated-state value. 2) The rate of change inrestistance value has been independent on the intensity of Gamma-Ray source when Carbon Resistor is irradiated in the same quantity of irradiation. 3) The resistance value in irradiated Carbon Resistor has not been varied with elapse of time. 4) The more the distance from the Carbon Resistor to the Gamma-Ray source the more greatly the resistance value is decreased and that it has been shown that the more quantity of irradiation by Gamma-Ray, the greater the rate of decrease in resistance value. Through the above results it has been concluded that the measurement values obtained by the high-precision instruments in the radiation field have to be corrected with proper consideration to radiation damages.

• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.17-21
• /
• 2005

We report the oscillation of the Josephson vortex-flow resistance in the rectangular stacks of $Bi_{2}Sr_{2}CaCu_{2}O_{8+x}$(Bi-2212) intrinsic Josephson junctions (IJJs). Apiece of Bi-2212 single crystal containing a few tens of IJJs was sandwiched between two gold electrodes and fabricated into a rectangular shape with the typical lateral size of about $1.5{\times}10\;{\mu}m^2$, using e-beam lithography and focused ion-beam etching techniques. In a tesla-range magnetic field applied in parallel with the junction planes, the oscillation of the Josephson vortex flow resistance was observed at temperatures near 60 K. The oscillation results from the interplay between the triangular Josephson vortex lattice and the potential barrier at the boundary of a single crystal. The oscillatory magnetoresistance for different bias currents, external magnetic fields, and the tilt-angles provides useful information on the dynamics of the coupled Josephson-vortex lattice system.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권3호
• /
• pp.15-20
• /
• 2018

No-insulation (NI) pancake magnets are fabricated using Rare earth-Barium-Copper Oxide (REBCO) coated conductor (CC) tapes, which enabled a very compact magnet in the aspects of high critical current density ($J_c$) and high mechanical strength by removing insulation and allowing thinner stabilizer. They have also advantages such as self-quench protection. Therefore, it does not need quench detection and protection that can be very challenging in a high critical temperature ($T_c$) superconducting magnet technology. Recently, it was reported that the NI REBCO CC magnets have some drawbacks of long charging time and high field ramp loss which will be a concern in the operation of cryocooled magnets. These issues are related to the turn-to-turn contact resistivity and can be released by managing it. This is also closely related to the activity of reducing the contact joint resistance in the case of CC joints for long length CC fabrication. Therefore, in this study, the turn-to-turn contact resistance ($R_c$) at the CC contact part of differently stabilized CC tapes was measured. The behaviors of $R_c$ at CC contact parts according to the applied contact pressure were investigated. The range of $R_c$ measured for CC tapes adopted will provide fundamental data for design and fabrication of the CC NI coils.

• 한국도로학회논문집
• /
• 제20권4호
• /
• pp.27-34
• /
• 2018

PURPOSES : The objective of this study is to evaluate the physical properties of recycled asphalt mixtures reinforced with glass fiber. METHODS : Firstly, mixing design was conducted on recycled asphalt mixture for use of 50% recycled aggregate. Various laboratory tests were performed on four types of recycled asphalt mixtures with different glass fiber content to evaluate the physical properties. The laboratory tests include indirect tensile strength test, dynamic modulus test, Hamburg wheel tracking test and tensile-strength ratio to evaluate cracks, rutting and moisture resistance of mixtures. RESULTS : The indirect tensile strength of fiber reinforced glass increased about 139.4%. As a result of comparing the master curves obtained by the dynamic modulus test, the elasticity was low in the low temperature region and high in the high temperature region when the glass fiber was reinforced. The glass fiber contents of PEGS 0.3%, Micro PPGF 0.1% and Macro PPGF 0.3% showed the highest moisture resistance and rutting resistance. CONCLUSIONS : The test results show that use of glass fiber reinforcement can increase the resistance to cracking, rutting, and moisture damage of asphalt mixtures. It is also necessary to validate the long-term performance of recycled asphalt mixtures with glass fiber using full scale pavement testing and field trial construction.