• Animal cells and systems
• /
• v.13 no.2
• /
• pp.153-160
• /
• 2009

The fine structural characteristics of the silk spinning apparatus in the titanoecid spiders Nurscia albofasciata have been examined by the field emission scanning electron microscopy (FESEM). This titanoecid spiders have a pair of medially divided cribella just in front of the anterior spinnerets, and the surface of the cribellum is covered by hundred of tiny spigots which produce numerous cribellate silk fibrils. The cribellar silks are produced from the spigots of the sieve-like prate. and considered as a quite different sort of catching silk with dry-adhesive properties. The other types of the silk spigots were identified as follows: ampullate, pyriform and aciniform glands. Two pairs of major ampullate glands send secretory ductules to the anterior spinnerets, and another 1-2 pairs of minor ampullate glands supply the middle spinnerets. In addition, the pyriform glands send ductules to the anterior spinnerets, and two kinds of the aciniform spigots feed silk into the middle (A type) and the posterior spinnerets (both of A & B types), respectively.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.233-234
• /
• 2009

In this paper, we report the characteristics of the continuous wave laser output of the $lima{\varsigma}on$-shaped InGaAsP microcavity laser pumped by current injection. In order to find the directions of emission far-field patterns are measureed by rotating an optical fiber around the microcavity. We observe high directionality of the $lima{\varsigma}on$-shaped microcavity laser. For the analysis of lasing properties we also investigate its polarization and spectrum using the Glan-Thompson polarizer and spectrum analyzer.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.2
• /
• pp.69-74
• /
• 2010

AlN thin films were deposited by using a two-facing-targets type sputtering system (TFTS), and their deposition characteristics, microstructure and texture were investigated. Total gas pressure was kept constant at 0.4 Pa and the partial pressures of nitrogen, $PN_2$ (($N_2$ pressure)/($Ar+N_2$ pressure)) varied from 0 to 0.4 Pa. The texture of the film cross-sections and surface morphology were observed by field emission scanning electron microscope (FE-SEM). The crystallographic orientation of the films were analyzed by X-ray diffraction (XRD). Deposition of AlN film depends on $N_2$ partial pressure. The best preferred oriented AlN thin films can be deposited at a nitrogen partial pressure of $PN_2$ = 0.52. As-deposited AlN films show preferred orientation and columnar structure, and the grAlN size of AlN films increases with increasing sputtering current.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.462-466
• /
• 2012

In this paper, heat-releasing composite sheets made of AlN, graphite, Al powder and acryl binder as thermoset were prepared using tape casting method. The crystal structure, morphology, thermal conductivity of heat-releasing composite sheet were measured by using X-ray diffractometer, field emission-scanning electron microscopy and laser flash instrument. It was found thermal conductivity of sheet was decided by solid content, composition including AlN, graphite, Al in heat-releasing composite sheets. As a result, 4.56 W/mK of thermal conductivity could be obtained by using LFA 447.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.431-434
• /
• 2012

In this paper, heat-releasing sheets made of AlN powder and acryl binder as thermoset were prepared using tape casting method. The crystal structure and morphology, the thermal properties as nonvolatile solid content and thermal conductivity, and the surface resistance of heat-releasing sheet were measured by using X-ray diffractometer, field emission-scanning electron microscopy, thermo gravimetric analyzer and laser flash instrument, and surface resistance meter. It was proved that thermal conductivity is greatly affected by the content of binder in heat-releasing sheet. Superior thermal conductivity above 3.5 W/mK and suface resistance were obtained at heat-releasing sheet with above 90% of AlN powder.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.123-126
• /
• 2011

Titanium dioxide ($TiO_2$) thin films were deposited by the sol-gel method with a surfactant-assisted mechanism. Its application for dye-sensitized solar cells (DSSCs) was investigated. Brunauer-Emmett-Teller, X-ray diffraction and field emission scanning electron microscopy techniques were used to characterize the surface characteristics of thin films. Photovoltaic-current density measurements were performed to determine the photoelectrochemical properties of the thin films and the performance of DSSCs. Energy conversion efficiency of about 6.1% was achieved for cells with conductive glass under illumination with AM 1.5 (100 $mWcm^{-2}$) simulated sunlight. Investigation showed higher photo-energy conversion efficiency for mesoporous $TiO_2$ nanocrystalline films used in DSSCs relative to commercially available Degussa P25 films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.485.1-485.1
• /
• 2014

In this research, we report the synthesis of three-dimensional (3D) hierarchical porous graphene aerogels (hpGAs) for application to electrochemical energy storage. For electrochemical systems, the specific capacitance is a key parameter to evaluate the characteristics of electrode materials. By taking full advantage of large surface area, 3D hpGAs would achieve the larger specific capacitance over rGO film and GAs. Microscopic structures and topologies of hpGAs were investigated using field emission scanning electron microscopy and transmission electron microscopy. X-ray photoelectron spectroscopy was used to determine the chemical compositions of rGO film, GAs, and hpGAs. Raman spectra were recorded from 100 to 2500 cm-1 at room temperature using a Raman spectroscopy equipped with a ${\times}100$ objective was used. The specific area and pore distribution of GAs and hpGAs were obtained using a Brunauer-Emmett-Teller apparatus.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.48.1-48.1
• /
• 2010

Cu has been used for metallic interconnects in ULSI applications because of its lower resistivity according to the scaling down of semiconductor devices. The resistivity of Cu lines will affect the RC delay and will limit signal propagation in integrated circuits. In this study, we investigated the characteristics of electroplated Cu films according to the variation of concentration of organic additives. The plating electrolyte composed of $CuSO_4{\cdot}5H_2O$, $H_2SO_4$ and HCl, was fixed. The sheet resistance was measured with a four-point probe and the material properties were investigated with XRD (X-ray Diffraction), AFM (Atomic Force Microscope), FE-SEM (Field Emission Scanning Electron Microscope) and XPS (X-ray Photoelectron Spectroscopy). From these experimental results, we found that the organic additives play an important role in formation of Cu film with lower resistivity by EPD.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.1
• /
• pp.15-28
• /
• 1995

Over the last two decades, air quality models have been developed and used in the United States. Many of these models ate distributed as parts of UNAMAP. These models have been used as useful tools for urban air quality management in Korea. However, when we use these models, many problems could be occured because of their different topographical and meteorological conditions. In the present study it is described that the characteristics about developement of the local scale diffusion models for application to Korea. Also for evaluation purpose of the models, input data requirements such as air pollutant concentrations, emission inventory, meteorological data, and field experiment data, were discussed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.11
• /
• pp.551-555
• /
• 2004

In this paper, in order to reduce the high COO (cost of ownership) and COC (cost of consumables), we have collected the silica abrasive powders by filtering method after subsequent CMP (chemical mechanical polishing) process for the purpose of abrasives recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size distribution and FE-SEM (field emission-scanning electron microscope) measurements of abrasive powders. It was annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slurry. As our experimental results, we obtained the comparable rate of removal and good planarity with commercial products. Consequently we can expect the saving of high cost slurry.