• Journal of the Korean Magnetics Society
• /
• v.3 no.4
• /
• pp.289-292
• /
• 1993

[Ni/Fe/Cu] and [Fe/Ni/Fe/Cu] multilayers were prepared with three gun rf-magnetron sputtering, and dependence of magnetoresistance on the Ni IFe thickness ratio was investigated. Vaccum annealing was tried to invetigated the effect of annealing. Oscillation of magnetoresistance on the Cu spacer thickness was dbserved in these two kinds of multilayers. When the thickness of Fe inserted into the Ni/Cu interface was about $3\;\AA$. the maximum value of magnetoresistance(13 %) could be observed. In a sample of $1~2\;\AA$ Fe thickness, saturation field decreased significantly, while magnetoresistace decreased slightly in comparison with the sample of $3\;\AA$ Fe. In ${[Cu(23\;\AA)/Fe(1\;\AA)/Ni(18\;\AA)/Fe(1\;\AA)]}_{20}/Fe(80\;\AA)/Si$, 6 % magnetoresistance with 100 Oe saturation field could be obtained. No appreciable change in magnetoresistance and saturation field could be observed by low temperature annealing. Formation of Ni-Fe alloy was not confinred.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.330-336
• /
• 2000

Effects of microstructure and indentation stress on fracture behavior of glass-infiltrated alumina composite for dental restorative application were investigated by the Hertzian and Vickers indentation method. Indentation stress-strain curve of glass-infiltrated alumina has showed the quasi-plastic behavior - deviation from linearity at high stress and the classical Hertzian cone crack, which could be confirmed the subsurface damage micrographs using bonded-interface specimen technique. The indentation stress-strain curves for the starting preforms are strongly dependent on porosity and microstructure of the preforms. On the other hand, the curves for the infiltrated composites are relatively insensitive to these factors. The failure of composite is originated at quasi-plastic deformation region. Damage and fracture behavior due to Hertzian stress field is theoretically examined, so that the indentation stress field plays a great role in material degradation. After Hertzian indentation annealing processing changes fracture behavior of alumina composite, so that stress field in material is healed through annealing.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1343_1344
• /
• 2009

In this work, transparent conducting Al-doped zinc oxide (AZO) films were prepared on Corning glass substrate by RF magnetron sputtering using an Al-doped ZnO target (Al: 2 wt.%) at room temperature and all films were deposited with athickness of 150 nm. We investigated the effects of the post-annealing temperature and the annealing ambient on structural, electrical and optical properties of AZO films. The films were annealed at temperatures ranging from 300 to $500^{\circ}C$ in steps of $100^{\circ}C$ using rapid thermal annealing equipment in oxygen. The thickness of the film was observed by field emission scanning electron microscopy (FE-SEM) and grain size was calculated from the XRD spectra using the Scherrer equation and their electrical properties were investigated using a hole measurement and the reflectance of AZO films was investigated by UV-VIS spectrometry.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.1-4
• /
• 2008

The electrical characteristics of polycrystalline silicon (poly-Si) thin film transistor (TFT) crystallized by excimer laser annealing (ELA) method were evaluated, The polycrystalline silicon thin-film transistor (poly-Si TFT) has higher electric field-effect-mobility and larger drivability than the amorphous silicon TFT. However, to poly-Si TFT's using conventional processes, the temperature must be very high. For this reason, an amorphous silicon film on a buried oxide was crystallized by annealing with a KrF excimer laser (248 nm)to fabricate a poly-Si film at low temperature. Then, High permittivity $HfO_2$ of 20 nm as the gate-insulator was deposited by atomic layer deposition (ALD) to low temperature process. In addition, the solid phase crystallization (SPC) was compared to the ELA method as a crystallization technique of amorphous-silicon film. As a result, the crystallinity and surface roughness of poly-Si crystallized by ELA method was superior to the SPC method. Also, we obtained excellent device characteristics from the Poly-Si TFT fabricated by the ELA crystallization method.

• Journal of the Korean Ceramic Society
• /
• v.29 no.1
• /
• pp.29-34
• /
• 1992

Phase transition, dielectric properties, and leakage current characteristics of Ta2O5 thin film fabricated by sol-gel process with tantalum penta-n-butoxide were studied as a function of annealing temperature in O2 atmoshpere. Although Ta2O5 thin film annealed at temperatures below 700$^{\circ}C$ for 1 hr was amorphous, it was crystallized to ${\beta}$-Ta2O5 of orthorhombic phase by annealing at temperatures higher than 750$^{\circ}C$. With increasing annealing temperature from 500$^{\circ}C$ to 900$^{\circ}C$, dielectric constant of sol-gel processed Ta2O5 thin film was changed from 17.6 to 15.3 due to the increase of SiO2 thickness at Ta2O5/Si interface. For Ta2O5 thin film annealed at 500$^{\circ}C$ to 800$^{\circ}C$ for 1 hr in O2 atmosphere, leakage current was remarkably reduced and breakdown strength was increased with higher annealing temperature. For Ta2O5 film annealed at 800$^{\circ}C$, breakdown did not occur even at electric field strength of 30${\times}$105V/cm and leakage current was maintained lower than 10-8A/$\textrm{cm}^2$.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1330-1336
• /
• 1994

Ta2O5 films were deposited on the p-Si(100) substrates by ECR-PECVD and annealed in O2 atmosphere. The thicknesses of Ta2O5/SiO2 layers were measured by an ellipsometer and a cross-sectional TEM. Annealing in O2 atmosphere enhanced the stoichiometry of the Ta2O5 film and reduced the impurity carbon content. Ta2O5 films were crystallized at the annealing temperatures above 75$0^{\circ}C$. The best leakage current characteristics and the maximum dielectric constant of Ta2O5/SiO2 film capacitor were observed in the specimen annealed at $700^{\circ}C$ and 75$0^{\circ}C$, respectively. The flat band voltage of the Al/Ta2O5/SiO2/p-Si MOS capacitor was varied in the range of -0.6~-1.6 V with the annealing temperature. The conduction mechanism in the Ta2O5 film, the variation of the effective oxide charge density with the annealing temperature, and the effective electric field distribution in the Ta2O5/SiO2 double layer were also discussed.

• Journal of the Korean Ceramic Society
• /
• v.37 no.2
• /
• pp.168-173
• /
• 2000

YMnO3 thin films were prepared on Pt/Ti/SiO2/Si substrate by chemical solution deposition method. The films were crystallized by heat-treatment at 85$0^{\circ}C$ for 1 hour. Effects of an annealing atmosphere(O2, Ar, vacuum) on the crystallization behavior and electridcal properties were investigated. YMnO3 thin films annealed under Ar atmosphere showed a superior crystallinity and a very strong c-aix preferred-orientation which was a polar axis. Leakage current density of the films decreased with lowering oxygen partial pressure of the annealing atmosphere. C-V and P-E ferroelectric hysteresis were observed only in the thin film heat-treated under Ar atmosphere.In order to prepare YMnO3 thin films having both low leakage current and ferroelectricity, the annealing atmsphere should be kept under a proper oxygen partial pressure which was about 1 Pa in this work. Leakage current density at 1 volt, dielectric constant($\varepsilon$r), remanent polarization(Pr), and coercive field(Ec) were 1.7$\times$10-8 A/$\textrm{cm}^2$, 25, 1.08$\mu$C/$\textrm{cm}^2$, and 100 kV/cm, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.12
• /
• pp.965-971
• /
• 2001

$\beta$-Ga$_2$O$_3$ nanobelts and nanoparticles were synthesized from mechanically ground GaN powders with thermal annealing in a nitrogen atmosphere and an oxygen atmosphere, respectively. The study of field emission scanning electron microscopy (FESEM) on the microstructures of nanomaterials revealed that the nanobelts synthesized in the nitrogen atmosphere are with the range of 20~1000nm width and 10 ~100nm thickness, and that nanomaterials are nanoparticles with 20~50nm radius obtained by thermal annealing in an oxygen atmosphere. The crystal structure of the $\beta$-Ga$_2$O$_3$ nanobelts and nanoparticles was in this study investigated by X-ray diffractometer (XRD) and high-resolution transmission electron microscope (HRTEM). The formation processes of the nanobelts and nanoparticles will be discussed in this paper.

• Journal of Digital Contents Society
• /
• v.19 no.2
• /
• pp.343-349
• /
• 2018

The proposed hybrid algorithm combines the benefits of rapid convergence property of mean filed annealing(MFA) and the effective genetic operations of simulated annealing-like genetic algorithm(SGA). This algorithm is applied to the isotropic material stock cutting problem, especially to glass cutting in distributed computing environments base on MPI called message passing interface. The glass cutting is to place the required rectangular patterns to the given large glass sheets resulting in reducing the wasted scrap area. Our experimental results show that the heuristic method improves the performance over the conventional ones by decreasing the scrap area and maximum execution time. It is also proved that the proposed distributed algorithm maintains the convergence properties of sequential one while it achieves almost linear speedup as the problem size increases.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.731-738
• /
• 2000

KLN(K3Li2Nb5O15) has attracted a great deal of attention for their potential usefulness in piezoelectric, electro-optic, nonlinear optic, and pyroelectirc devices. Especially, the KLN single crystal has been studied in the field of optics and electronics. However it is hard to produce good quality single crystals due to the crack propagation during crystal growing. One of the solutions of this problem is prepartion of thin film. But the intensive study has not been conducted so far. In this study, after the KLN thin film were prepared by R.F. magnetron Sputtering method on SiO2/Si substrate, the post-annealing methods of RTA(rapid thermal annealin) and IPA(insitu post annealing) were employed. The deposition condition of KLN thin film was RF power(100 W), Working pressure(100 mtorr). The commonness of both RAT and IPA was that the higher were deposition and post annealing temperature, the higher was the intensity of XRD but the less surface roughness. The difference of post-annealing methods affected XRD phase and surface condition very much. And in IPA process, the influence of O2 had much effect on the formation of KLN phase.