• Computers and Concrete
• /
• v.22 no.3
• /
• pp.337-353
• /
• 2018

The present study focuses on examining the structural behaviour of steel-fibre-reinforced concrete (SFRC) beams under high rates of loading largely associated with impact problems. Fibres are added to the concrete mix to enhance ductility and energy absorption, which is important for impact-resistant design. A simple, yet practical non-linear finite-element analysis (NLFEA) model was used in the present study. Experimental static and impact tests were also carried out on beams spanning 1.3 meter with weights dropped from heights of 1.5 m and 2.5 m, respectively. The numerical model realistically describes the fully-brittle tensile behaviour of plain concrete as well as the contribution of steel fibres to the post-cracking response (the latter was allowed for by conveniently adjusting the constitutive relations for plain concrete, mainly in uniaxial tension). Suitable material relations (describing compression, tension and shear) were selected for SFRC and incorporated into ABAQUS software Brittle Cracking concrete model. A more complex model (i.e., the Damaged Plasticity concrete model in ABAQUS) was also considered and it was found that the seemingly simple (but fundamental) Brittle Cracking model yielded reliable results. Published data obtained from drop-weight experimental tests on RC and SFRC beams indicates that there is an increase in the maximum load recorded (compared to the corresponding static one) and a reduction in the portion of the beam span reacting to the impact load. However, there is considerable scatter and the specimens were often tested to complete destruction and thus yielding post-failure characteristics of little design value and making it difficult to pinpoint the actual load-carrying capacity and identify the associated true ultimate limit state (ULS). To address this, dynamic NLFEA was employed and the impact load applied was reduced gradually and applied in pulses to pinpoint the actual failure point. Different case studies were considered covering impact loading responses at both the material and structural levels as well as comparisons between RC and SFRC specimens. Steel fibres were found to increase the load-carrying capacity and deformability by offering better control over the cracking process concrete undergoes and allowing the impact energy to be absorbed more effectively compared to conventional RC members. This is useful for impact-resistant design of SFRC beams.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.2
• /
• pp.240-247
• /
• 2012

Dietary supplementation with conventional linted cottonseed hulls (LCSH) is a common practice in livestock production all over the world. However, supplementation with mechanically delinted cottonseed hulls (DCSH) and cottonseed linter residue (CLR) is uncommon. Cottonseed by-products, including LCSH, DCSH and CLR, were assessed by chemical analysis, an in situ nylon bag technique, an in vitro cumulative gas production technique and in vitro enzyme procedure. The crude protein (CP) content of CLR (302 g/kg dry matter (DM)) was approximately 3 times that of LCSH and 5 times that of DCSH. The crude fat content was approximately 3 times higher in CLR (269 g/kg DM) than in LCSH and 4 times higher than in DCSH. Neutral detergent fibre (311 g/kg DM) and acid detergent fibre (243 g/kg DM) contents of CLR were less than half those of DCSH or LCSH. Metabolisable energy, estimated by in vitro gas production and chemical analyses, ranked as follows: CLR (12.69 kJ/kg DM)>LCSH (7.32 kJ/kg DM)>DCSH (5.82 kJ/kg DM). The in situ degradation trial showed that the highest values of effective degradability of DM and CP were obtained for CLR (p<0.05). The in vitro disappearance of ruminal DM ranked as follows: CLR>LCSH>DCSH (p<0.05). The lowest digestibility was observed for DCSH with a two-step in vitro digestion procedure (p<0.05). The potential gas production in the batch cultures did not differ for any of the three cottonseed by-product feeds. The highest concentration of total volatile fatty acids was observed in CLR after a 72 h incubation (p<0.05). The molar portions of methane were similar between all three treatments, with an average gas production of 22% (molar). The CLR contained a higher level of CP than did LCSH and DCSH, and CLR fermentation produced more propionate. The DCSH and LCSH had more NDF and ADF, which fermented into greater amounts of acetate.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.9
• /
• pp.25-32
• /
• 2006

In this study, the characteristics of filament wound composite/aluminum ring specimens were investigated at cryogenic temperature. The ring specimens were manufactured using carbon fibre and Type B epoxy resin which had been developed for cryogenic use. As a result of measuring thermal strains at -150℃, it was found that compressive thermal stress was induced in composite part on the contrary, tensile thermal stress in aluminum part which was about 32% of yield stress and in turn, caused aluminum to be yielded at lower load level. In addition, Thermal strains which resulted from finite element analysis showed good agreement with those of the experiment. After 6 mechanical loading cycles had been applied to the ring specimen at -150℃, tensile tests were performed at -150℃ using a split disk fixture. As a result, it was shown that composite strength in a liner-composite tank structure which is for the use of cryogenic propellant tank would be decreased by auto-frettage pressure which is applied to it.

• Fashion & Textile Research Journal
• /
• v.17 no.2
• /
• pp.295-304
• /
• 2015

This paper investigated wear comfort property of heat storage knitted fabrics for high emotional garment. For this purpose, ZrC imbedded PET knitted fabric was prepared and various physical properties such as thermal, wicking and drying characteristics were measured. In addition, far-infrared emission characteristics of ZrC imbedded PET was analysed and tactile hand property and dye affinity of ZrC imbedded knitted fabric were also studied in comparison with regular and other commercial heat storage PET knitted fabrics. It was observed that Zr imbedded amount in the yarn was 19.29% by ingredient analysis and far-infrared emission energy was $3.65{\times}10^2W/m^2$, emissivity was 0.906 at the range of wavelength $6{\sim}20{\mu}m$. It was found that maximum heat flow (Qmax) of ZrC imbedded PET knitted fabric was lower than that of regular PET one and warmth keepability rate was higher than that of regular PET one, which means ZrC imbedded PET have heat storage property. Drying property of ZrC imbedded knitted fabric was better than that of regular PET one due to heat by far-infrared emitted from ZrC in the core of filament. It revealed that wicking property of the ZrC imbedded fabric was not influenced by far-infrared emission, but affected by fibre physical properties. Tactile hand property of ZrC imbedded knitted fabric was not influenced by imbedding ZrC in the filament but affected preferably by structure of knitted fabric. Dye affinity of ZrC imbedded PET knitted fabric was less influenced by dyeing temperature and time than regular PET knitted one.

• Journal of Fashion Business
• /
• v.14 no.2
• /
• pp.138-150
• /
• 2010

In the dyeing of cotton and silk fibres using Caesalpinia sappan, the effects of pH changes of the Caesalpinia sappan dye liquor on the color were examined. In order to adjust the pH of the Caesalpinia sappan dye liquor, Schisandra chinensis extract and carboxylic acid were used for acidic condition, lye and the NaOH aqueous solution were used for alkaline condition. By introducing the dyeing method of pH adjustment, firstly, the effect on the reddish color inherent to the Caesalpinia sappan was examined. At the same time, the manifestation of the yellow color, which affect the manifestation of the red color greatly, was examined in detail quantitatively. By dyeing the cotton and silk fabrics, the inherent relationships established between the pH hanges and the fibre characteristics were sought to be examined.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.11
• /
• pp.1610-1616
• /
• 2006

Influence of different levels of corn steep liquor (CSL) on chemical composition of urea treated wheat straw (UTWS), ruminal characteristics, digestion kinetics, nitrogen (N) utilization, and nutrient digestibility by ruminally-cannulated buffalo bulls was studied in a $4{\times}4$ Latin Square Design. The CSL was used to ensile 5% UTWS at the rate of 0, 3, 6, and 9% on a dry matter (DM) basis. Total N and neutral detergent fibre (NDF) were increased with increasing level of CSL. Increased NDF content was attributable to increased neutral detergent insoluble nitrogen. Four diets were formulated to contain 20% concentrate and 80% UTWS ensiled with 0, (control), 3 (CSL3), 6 (CSL6), and 9% CSL (CSL9). All diets were mixed daily and fed at 1.5% of body weight twice daily. Ruminal NH3 concentration decreased with level of CSL used to ensile UTWS at 3 and 6 h post prandial, however, at 9 h post parandial it was similar across all diets and at 12 h post prandial was higher with diets containing UTWS ensiled with CSL. Concentrations of total ruminal volatile fatty acid and acetate were increased with the CSL level used to ensile UTWS. Increased rate of disappearance and reduction in lag time of DM and NDF was recorded with diets containing UTWS ensiled with CSL. Dry matter and NDF digestibilities were higher with CSL diets than on the control diet. Buffalo bulls retained more N with diets containing UTWS ensiled with CSL. The present results indicated that UTWS could be ensiled with CSL to improve its nutritive value and N utilization by ruminants.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.7
• /
• pp.988-993
• /
• 2012

Four experimental diets were formulated to contain 700 g/kg cereal with decreasing levels of wheat:barley inclusion. Diet 1 contained 700 g/kg wheat, diet 2 contained 600 g/kg wheat and 100 g/kg barley, diet 3 contained 500 g/kg wheat and 200 g/kg barley and diet 4 contained 400 g/kg wheat and 300 g/kg barley. The diets were offered to pigs on three trials to investigate effects on the performance of individually (n = 72) and group housed (n = 480) pigs and on nutrient digestibility in pigs housed in metabolizm crates (n = 24). Performance was assessed from 10 wks of age until slaughter and carcass characteristics were measured. For the group performance study, one pig from each pen (in total 24) at 10, 15 wks and at finish were slaughtered to ascertain scores for stomach ulceration, stomach weights and intestinal length. Level of wheat inclusion did not significantly (p>0.05) affect liveweight gain (LWG) or feed conversion ratio (FCR). Feed intake was lowest (p<0.05) for individually housed pigs offered diets containing 700 g/kg wheat during the 10-15 wk period, which indicated that individually housed pigs attempted to eat to a constant energy intake. There was little evidence of stomach ulceration across treatments and increasing wheat inclusion had no detrimental effect. Higher levels of wheat inclusion tended to increase backfat depth at the $P_2$ position which could lead to increasing grading penalties in a commercial situation although more research is required in this area. Increasing level of wheat inclusion increased digestible energy (DE) content but the lack of effect on FCR and killing out percentage indicated that utilization of energy from barley and wheat was similar. Digestibility coefficients increased linearly with increasing wheat content, which can be attributed to the lower level of fibre and higher level of starch in wheat compared with barley.

• Food Science of Animal Resources
• /
• v.40 no.3
• /
• pp.388-400
• /
• 2020

This study was conducted to develop chicken meat patties by incorporating pomegranate peel and bagasse powders and their extracts. Patties were developed by incorporating pomegranate peel powder (PPP, 2 g), pomegranate aril bagasse powder (PABP, 4 g), pomegranate peel powder aqueous extract (PPAE, 6 g) and pomegranate aril bagasse powder aqueous extract (PABAE, 9 g) individually per 100 g of minced meat. Both types of powders and extracts treated patties had significantly higher total phenolic content than control and butylated hydroxytoluene (BHT) treated patties. Both types of powder (PPP and PABP) treated patties had significantly higher water holding capacity, ash, crude fibre content, and hardness values, and significantly lower moisture content and lightness values in comparison to control patties. Emulsion stability and cooking yield of PABP treated patties were significantly higher than control. Addition of extracts and BHT did not influence the physico-chemical properties and proximate composition of chicken patties. Both types of powders and extracts provided better protection to chicken meat patties against oxidative rancidity and microbial proliferation in comparison to control and BHT treated patties during refrigerated storage. It is concluded that pomegranate fruit byproducts in the form of peel powder, aril bagasse powder and their extracts can be successfully utilised in development of healthier chicken meat patties and these byproducts can also be effectively used as a replacement of synthetic antioxidants such as BHT.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.12
• /
• pp.1726-1730
• /
• 2000

High fibre (CF, 242 g/kg) sunflower seed meal (SSM) was incorporated in standard grower and layer quail diets at 0, 50, 75 or 100 g/kg replacing part of the soybean meal (SBM) and deoiled rice bran (DORB). Each grower diet was offered to 30 quails housed in battery cages from day one to 5 weeks of age. At the end of the growing period, Twelve female quails from each of the four respective dietary groups were transferred to the individual laying cages and their laying performance from 7 to 20 weeks of age were evaluated on diets containing SSM at similar levels as that during the growing period. The results of growth bioassay revealed that the live weight gain, feed intake, nutrient retention and carcass characteristics of quails in different dietary groups did not vary significantly (p>0.05), although the quails fed SSM based diets utilized the feed less (p<0.05) efficiently than those fed the control diet. During the laying period, the egg production and egg quality traits remained unaffected due to dietary treatments but feed required per unit egg production increased (p<0.05) as the level of SSM in diet was increased to 100 g/kg. Although, the cost of feed per kg decreased due to the incorporation of SSM in diet but the same was not reflected in feed cost per unit gain, meat or egg production as such parameters were comparable on all the diets. It could thus be concluded that the SSM can be incorporated in quail diets upto 100 g/kg for part of SBM, an item usually expensive and also in short supply in developing countries including India.

• Smart Structures and Systems
• /
• v.21 no.3
• /
• pp.257-262
• /
• 2018

Vibrational problems in the domestic Small Horizontal Axis Wind Turbines (SHAWT) are due to flap wise vibrations caused by varying wind velocities acting perpendicular to its blade surface. It has been reported that monitoring the structural health of the turbine blades requires special attention as they are key elements of a wind power generation, and account for 15-20% of the total turbine cost. If this vibration problem is taken care, the SHAWT can be made as commercial success. In this work, Shape Memory Alloy (SMA) wires made of Nitinol (Ni-Ti) alloys are embedded into the Glass Fibre Reinforced Polymer (GFRP) wind turbine blade in order to reduce the flapwise vibrations. Experimental study of Nitinol (Ni-Ti) wire characteristics has been done and relationship between different parameters like current, displacement, time and temperature has been established. When the wind turbine blades are subjected to varying wind velocity, flapwise vibration occurs which has to be controlled continuously, otherwise the blade will be damaged due to the resonance. Therefore, in order to control these flapwise vibrations actively, a non-linear current controller unit was developed and fabricated, which provides actuation force required for active vibration control in smart blade. Experimental analysis was performed on conventional GFRP and smart blade, depicted a 20% increase in natural frequency and 20% reduction in amplitude of vibration. With addition of active vibration control unit, the smart blade showed 61% reduction in amplitude of vibration.