• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.2
• /
• pp.53-60
• /
• 2010

Kudzu vine (Pueraria lobata) is a perennial plant and spreads all around in South Korea. Recently the use of leaves, stems and roots of kudzu vine has been investigated in many fields. However, the research on kudzu fibers has not been performed in korean pulp and paper industry. As the stems and roots of kudzu were estimated to contain cellulosic fibers, the possibility of producing a raw material from kudzu fibers in pulp and paper mills was investigated in this study. The stems and roots of kudzu were collected in woods, and then the chemical composition and ash contents was measured. To acquire kudzu pulp, kraft pulping and bleaching of kudzu roots were carried out sequently. After making kudzu pulp, freeness and fiber length were measured, and handsheets was also prepared with kudzu pulp and the properties of handsheets were determined. Consequently, kudzu fibers have lower holocellulose contents than wood fibers and other non-wood fibers. Average fiber length is shorter than that of Sw-BKP, but shows the same level as that of Hw-BKP. The handsheet made from kudzu pulp shows the bulkier structure than those made from Hw-BKP and Sw-BKP.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.245-252
• /
• 2020

This study was performed to analyze the mechanical properties of tropical hybrid cross-laminated timber (CLT) with bamboo laminated board as the core layer in order to evaluate the possibility of its use as a CLT material. Bamboo board was used as the core layer and the tropical species Acacia mangium willd., from Indonesia, was used as the lamination in the outer layer. The modulus of elasticity (MOE), modulus of rupture (MOR), and shear strength of the hybrid CLT were measured according to APA PRG 320-2018 Standard for Performance-Rated Cross-Laminated Timber. The results show that the bending MOE of the hybrid CLT was found to be 2.76 times higher than SPF (Spruce Pine Fir) CLT. The reason why the high MOE value was shown in bamboo board and hybrid CLT applied bamboo board is because of high elasticity of bamboo fiber. However, the shear strength of the hybrid CLT was 0.8 times lower than shear strength of SPF CLT.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.5
• /
• pp.555-562
• /
• 2014

Characteristics of carbonized fiberboard such as chemical materials absorption, electromagnetic shielding, and electrical and mechanical performance were determined in previous studies. The carbonized board therefore confirmed that having excellent abilities of these characteristics. In this study, the effect of density on physical properties and sound absorption properties of carbonized fiberboards at $800^{\circ}C$ were investigated for the potential use of carbonized fiberboards as a replacement of conventional sound absorbing material. The thickness of fiberboards after carbonization was reduced 49.9%, 40.7%, and 43.3% in low density fiberboard (LDF), medium density fiberboard (MDF), and high density fiberboard (HDF), respectively. Based on SEM images, porosity of carbonized fiberboard increased by carbonization due to removing adhesives. Moreover, carbonization did not destroy structure of wood fiber based on SEM results. Carbonization process influenced contraction of fiberboard. The sound absorption coefficient of carbonized low density fiberboard (c-LDF) was higher than those of carbonized medium density fiberboard (c-MDF) and carbonized high density fiberboard (c-HDF). This result was similar with original fiberboards, which indicated sound absorbing ability was not significantly changed by carbonization compared to that of original fiberboards. Therefore, the sound absorbing coefficient may depend on source, texture, and density of fiberboard rather than carbonization.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.85-90
• /
• 2015

To use the African tulip tree (Spathodea campanulata) as raw material for chemical pulping, soda and soda-AQ pulping was investigated. In chemical compositional analysis, lignin contents of African tulip (33.1%) was higher than other hardwood such as Yellow poplar (17.5%), Acacia (27.1%), or Eucalyptus (24.2%). Soda or soda-AQ pulping with African tulip tree resulted in yield at 43.4-44.8% with 29.5-34.5 Kappa number, pulping condition with 20-22% active alkali. Kappa number of African tulip tree pulp was quite higher than other tropical hardwood (Eucalyptus or Accacia) with less yield due to higher lignin content in wood. Fiber length and width of pulp from African tulip tree was similar to Accacia pulp and shorter than eucalyptus pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.3
• /
• pp.81-87
• /
• 2014

Conditions of paper manufacturing process should be changed depending on the end use and paper properties. Most of the case, mixed pulps with long softwood fibers and short hardwood fibers are used to achieve proper qualities of product with reasonable production cost. For specialty paper manufacture the wood pulp and cotton linter pulp are usually mixed together. The objectives of this study is to analyze physical, mechanical and fracture mechanical properties of paper depending on SwBKP, HwBKP and cotton linter pulp(CLP) mixing. When the mixing ratio of SwBKP was increased, strength properties, such as tensile, tear, and folding endurance, were also increased. When the mixing ratio of SwBKP and HwBKP was increased, stress concentration index was decreased and fracture toughness was increased.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.4
• /
• pp.65-78
• /
• 1990

For the purpose of Improving the sounding boards for the conventional GAYAKUM, I was making approximately 202 specimens of radial board, 371 specimens of tangential board by cutting along the grain and the part of stem and 31 specimens of the disjointed traditional GAYAKUM made in Paulownia coreana. And it was conducted to measure specific gravity, dynamic Young's modulus, internal friction, resonant frequency, velosity of sound and width of annual ring by the method of the frexural vibration in a free-free bar in the audio frequency range. And it confirmed the juvenile wood by measuring wood fiber length of specimens. It was also conducted to investigate dynamic properties and moisture absorption by various heat-treatment and to test dynamic Young's modulus and internal friction for the disjointed conventional GAYAKUM. The results obtained were summarized as follow: 1. The Juvenile wood is located within about 7 annual rings from the pith in Paulownia coreana. 2. As increased with the specific gravity, the dynamic Young's modulus had more and more increased, but the internal friction had slightly decreased. 3. I think that radial board would be good for sounding board wood. because radial board is higher than tangential board in dynamic Young's mudulus and internal friction is lower than tangential board. 4. The value of mean dynamic Young's modulus on the conventional GAYAKUM, radial board and tangential board of 604 samples is $0.4283\pm0.037(\times10^{11}dyne/cm^2)$, $0.4316\pm(\times10^{11}dyne/cm^2)$ and $0.4234\pm0.112(\times10^{11}dyne/cm^2)$ respectively. The value of the radial board showed little higher than that of conventional GAYAKUM, but It had a similar tendency between conventional GAYAKUM and tangential board. 5. The annual ring width by four aspect is more narrow in north and west than that of others. 6. The values of specific gravity and dynamic Young's modulus in the mature wood showed higher than those of juvenile wood. 7. As the grain angle in the butt wood more increased to bark from pith, the dynamic Young's modulus were low. Then it was not good for sounding board. 8. It appeared that the heat-treatment for sounding board wood had a more effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature. 9. As increased with the temperature, the rate of moisture absorption of heat-treatment wood had decreased. In conclusion, I thought that the sounding board wood for GAYAKUM would had the most effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature using the radial board of mature wood.

• Korean Chemical Engineering Research
• /
• v.59 no.4
• /
• pp.548-556
• /
• 2021

This study was conducted to investigate the applicability of lignocellulosic fiber and coconut shell activated carbon (CSA) for the production of a particulate matter (PM)-reducing air-filter as raw materials to solve the environmental problems of non-woven fabrics. CSA had a good potential to use as a raw material of air-filter for reducing volatile organic compounds as well as noxious metals, and reduction capability of the CSA was 5 times higher than that of wood fiber. Natural adhesives formulated with proteinaceous wastes mostly were applied successfully to fabricate air-filters with the shape of fiberboard. The air-filter fabricated with the minimum target density of 200 kg/m³ and the maximum CSA-content of 40 wt% in fiberboard had a good manageable strength. However, the fiberboard filters was required to make vent-holes for improving an air-permeability of the filters. Size of the CSA particles was adjusted to greater than 2 mesh with the consideration of strength and formability of the fiberboard. Three-layers fiberboard that only wood fiber and the mixture of wood fiber and CSA were formed in the surface and middle layers, respectively, was determined to the optimal condition for the production of air-filters. In addition, traditional Korean paper handmade from mulberry trees (TKP) showed a good PM-reducing property as an air-filter. It is concluded that air-filtering set composed of fiberboard with vent-holes and TKP instead of conventional air-filters made with non-woven fabrics can be used as a filter for reducing the concentrations of PM, VOC and noxious metals existed in indoor and outdoor spaces.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2007.11a
• /
• pp.93-102
• /
• 2007

Biocomposite was organized with biodegradable polymer and natural fiber that has potential to be used as replacement for glass fiber reinforced polymer composite with the benefits of low cost, low density, acceptable specific strength, biodegradability, etc. Until now, non-wood fibers have been used as reinforcements of biocomposite which are all plant-based fibers. The present study focused on investigating the fabrication and characterization of biocomposite reinforced with red algae fiber. The bleached red algae fiber(BRAF) showed very similar crystallinity to the cellulose. It has high stability against thermal degradation (maximum thermal decomposition temperature of 359.3$^{\circ}C$) and thermal expansion. Biocomposites reinforced with BRAF have been fabricated by a compression molding method and their mechanical and thermal properties have been studied. The storage modulus and the thermomechanical stability of PBS matrix are markedly improved with reinforcing the BRAF. These results support that the red algae fiber can be used as an excellent reinforcement of biocomposites as "green-composite" or "eco-composite".

• Journal of the Korea Furniture Society
• /
• v.14 no.1
• /
• pp.1-9
• /
• 2003

This research was carried out for packing materials and building materials to examine thylene gas adsorption and effect of keeping fruit fresh of wet formed charcoal-fiber mposite made from defibrated fiber of Pinus densiflora Sieb. et Zucc. and white charcoal from uercus variabilis Bl.(wood fiber: charcoal=8:2, 6:4, 4:6, 2:8), with/without phenol formaldehyde resin(PF, Non volatile content:$52\%$, resin content $1,3,5\%$). The results are summarized as follows: 1. The higher the charcoal content, the more the ethylene gas adsorption. At the same mixing ratio of fiber to charcoal, $\#100-200$ of charcoal particle size gave the better reslts than $\#60-100$. 2. Adding PF into the charcoal fiber composite decreased the capacity of ethylene gas adsorption but there was no significant difference until $5\%$ adding amount of PF. 3. For keeping fruit fresh for a long time, Charcoal fiber composite was $66\%$ longer than control. The higher the white charcoal content, the longer fresh time.

• Textile Coloration and Finishing
• /
• v.32 no.1
• /
• pp.44-50
• /
• 2020

In this study, pre-treatment was performed on kapok, a hydrophobic fiber, to compare dyeability by hydrophilization. The pretreatment conditions of kapok fiber were used with different amounts of sodium oleate(NaO), a fatty acid-based anionic surfactant, and xanthan gum(XG) as a natural thickener. At this time, NaO and XG were separately or mixed treated with 0.01%, 0.1%, 1% aqueous solution at 80℃ for 30 min. Hydrophilicity through dyeing was confirmed using Sappan wood extract. Therefore, SEM observation was performed to investigate the surface change of kapok fiber according to the conditions. The surface color difference was also analyzed. Pretreated kapok fibers were made from nonwoven fabrics and the contact angles were measured to determine their hydrophilization. The surface of the fiber after pretreatment was found to be cracked when NaO and NaO were mixed with XG. The surface color was the highest in a^⁎ and K/S values after the simultaneous treatment of NaO and XG, followed by NaO pretreatment and XG pretreatment. The contact angle of kapok fiber made of nonwoven fabric was slightly lower at 300g/㎡ than the fabric weight of 150g/㎡. Such hydrophilized nonwoven kapok fiber are expected to be used in various fields.