• Journal of The Korean Society of Agricultural Engineers
• /
• v.58 no.1
• /
• pp.53-59
• /
• 2016

This study was conducted by the slump test and the consistency test of the fiber mixed soil which is soil reinforced with fiber as a reinforced material to investigate and estimate the difficulty degree of work and the proper water content. So I would like to present the fundamental data that establishes the work standard of the fiber mixed soil. In conclusion, in this study the slump value of the fiber mixed soil increases over-all according to the increase of the water content although it has a little difference of the increase range and it is smaller than one of the soil. It is estimated that the aggregating and throwing work of the fiber mixed soil would be fine when it has the about 25 % water content and the wall and floor plastering work is the about 30 % ~ 35 % and the flowing and pouring work is the about 40 % water content as well as the mold compacting work is the about 20 %. There is no decreasing of the workability when the soil is reinforced by the fiber because the workability characteristics of the fiber mixed soil is similar to the one of the soil. Therefore, It is estimated that using the fiber as a reinforced material of soil would be appropriate for the construction.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.40-41
• /
• 2015

The purpose of this study is to develop advaced furture type of concrete which utilizes transpart plastic types of fiber replacing previously used high price optical fiber and porous type of steel mold to induce its mass production. New type of concrete solved problems of construction and economy can make it easily their application to construction market.

• Composites Research
• /
• v.34 no.6
• /
• pp.426-433
• /
• 2021

The carbon fiber reinforced plastic manufacturing process has a problem in that a dimensional error occurs due to thermal deformation such as residual stress, spring-in, and warpage. The main causes of thermal deformation are various, including the shape of the product, the chemical shrinkage, thermal expansion of the resin, and the mold effect according to the material and surface condition of the mold. In this study, a viscoelastic model was applied to the plate model to predict the thermal deformation. The effects of chemical shrinkage and thermal expansion of the resin, which are the main causes of thermal deformation, were analyzed, and the analysis technique of the 3-D viscoelastic model with and without mold was also studied. Then, the L-shaped mold effect was analyzed using the verified 3D viscoelastic model analysis technique. The results show that different residual deformation occurs depending on the surface condition even when the same mold is used.

• Asian-Australasian Journal of Animal Sciences
• /
• v.7 no.3
• /
• pp.413-419
• /
• 1994

Mold growth decreased nutritive value of wheat straw (WS). Mold increased DM (94 vs 98%) and ADF (51 vs 56%) contents and had no effect on natural detergent fiber (NDF). Crude protein and N values were decreased in moldy wheat straw, Mold increased insoluble N content of wheat straw (WS) from 21 to 27%. Ammoniation increased the CP of nonmoldy straw from 3.8 to 8.3% and moldy straw from (3.3 to 6.2%). Aspergillus and zygomycetes fungal species were most prevalent and total numbers were higher on moldy straw. Ammoniation decreased total numbers of fungal spores on nonmoldy and moldy WS. Ammoniation of moldy WS increased (p < 0.10) feed in take (1.8%) as compared with nonmoldy, ammoniated, nonmoldy and moldy WS. Steers fed moldy WS had lowest (p < 0.10) feed intake (1.3% of BW daily) compared with other diet. There was little difference (p < 0.10) in intake of nonammoniated vs. ammoniated WS. Steers fed moldy straw lost 6 kg BW. Ammoniated, nonmoldy straw elevated Blood Urea Nitrogen (BUN) (10.5 mg/dl). Alkaline Phosphatase (ALK) was greater in steers fed moldy VS nonmoldy straw (148 VS 95 U/liter. p < 0.10).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.7
• /
• pp.681-686
• /
• 2009

Direct laser metal forming technology was applied to restore the damaged mold surface. In order to estimate melting characteristics of the $20{\mu}m$ Fe-Cr-Ni powder, single layer experiments were performed at various levels of heat input. The process window of the $20{\mu}m$ Fe-Cr-Ni powder provided feasible process parameters for the smooth regular surface. The cross hatching scanning strategy on the multiple layer experiment was performed to reduce the thickness non-uniformity of edge portions compared with the one direction scanning. To estimate the coherence between the melted powder and the basematal, the tendency of hardness distribution has been observed. The hardness of the melted and the remelted zone was distributed from 400HV to 600HV. It is over 2 times compared of the hardness of the basemetal. Experimental results show that the mold restoring process using direct laser metal forming can be successfully applied in the mold repair industry.

• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.283-298
• /
• 2007

Environment-friendly composites reinforced with bagasse fiber (BF), a kind of natural fiber as the remains from squeezed sugarcane, were fabricated by injection molding and press molding. As appropriate matrices for injection molding and press molding, polypropylene (PP) and polycaprolactone-cornstarch (PCL-C) were selected, as a typical recyclable resin and biodegradable resin, respectively. The mechanical properties of BF/PP composites were investigated in view of fiber mass fraction and injection molding conditions. And the mechanical properties and the biodegradation of BF/PCL composites were also evaluated. In the case of injection molding, the flexural modulus increased with an increase in fiber mass fraction, and the mechanical properties decreased with an increase in cylinder temperature due to the thermal degradation of BF. The optimum conditions increasing the flexural properties and the impact strength were $90^{\circ}C$ mold temperature, 30 s injection interval, and in the range of 165 to $185^{\circ}C$ cylinder temperature. On the other hand, as to BF/PCL-C fully-green composites, both the flexural properties and the impact strength increased with an increase in fiber mass fraction. It is considered that the BF compressed during preparation could result in the enhancement in mechanical properties. The results of the biodegradability test showed the addition of BF caused the acceleration of weight loss, which increased further with increasing fiber content. This reveals that the addition and the quantities of BF could promote the biodegradation of fully-green composites.

• International Journal of Aerospace System Engineering
• /
• v.1 no.1
• /
• pp.21-28
• /
• 2014

In this study, an investigation on mechanical properties of flax natural fiber composite is performed as a precedent study on the design of eco-friendly structure using flax natural fiber composite. The Vacuum Assisted Resin Transfer Molding-Light (VARTML) manufacturing method is adopted for manufacturing the flax fiber composite panel. The VARTML is a manufacturing process that the resin is injected into the dry layered -up fibers enclosed by a rigid mold tool under vacuum. In this work, the resin flow analysis of VARTM manufacturing method is performed. A series of flax composite panels are manufactured, and several kinds of specimens cut out from the panels are tested to obtain mechanical performance data. Based on this, structural design of chemical storage tank for agricultural vehicle was performed using flax/vinyl ester. After structural design and analysis, the resin flow analysis of VARTM manufacturing method was performed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.184-187
• /
• 2002

Compression molding was specifically developed for replacement of metal components with composites. As the mechanical properties of the products are dependent on the separation and orientation, it is important to research the fiber mat structure and molding conditions. In this study, the effects of the fiber mat structure(NP: 5, 10, 25punches/$\textrm{cm}^2$) and the mold closure speed($\dot{\textrm{h}}$=0.1, 1, 10mm/min) on the viscosity of composites were discussed. The composites is treated as a Non-Newtonian power-law fluid. The parallel-plate plastometer is used and the viscosity is obtained from the relationship between the compression load and the thickness of the specimen.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.840-843
• /
• 2004

UV molding is a process for integrating micro/nano polymeric optical components on optoelectronic modules. In the present study, a microlens array for vertical cavity surface emitting laser(VCSEL) to fiber coupling was designed, integrated and tested. At the design stage, design variables ware optimized to maximize the coupling efficiency, and tolerance analysis was carried out. At the integration stage, the UV transparent mold was fabricated and the microlens array on VCSEL array was integrated by UV molding process. Finally the coupling efficiency of VCSEL to fiber was measured and analyzed.

• Polymer(Korea)
• /
• v.38 no.6
• /
• pp.708-713
• /
• 2014

Most plastics products are being produced by injection molding process. However, mold shrinkage is inevitable in injection molding process and it deteriorates dimensional quality through deflections and warpages. Mold shrinkage depends upon the material property of resin as well as injection molding condition. In this study, material property of resin has been predicted for glass fiber reinforced polycarbonate to control the warpage, and computer simulation of injection molding has been performed using predicted property. It was observed that the deflection of part decreased by the glass fiber reinforced resin. In order to verify the validity of this method and confidence of results, experiments of injection molding were performed. The results of experiments and computer simulations showed good agreement in their tendency of deflections. Consequently, it was concluded that the method of designing the material property of resin conducted in this study can be utilized to control the dimensional accuracy of injection molded products.