• 비파괴검사학회지
• /
• 제13권1호
• /
• pp.7-14
• /
• 1993

In order to analyze the stress distribution and stress concentration factors in composite materials, especially, in the short fiber of the reinforced composite materials by photoelastic method, it is necessary to develop the photoelastic model material having short fibers with arbitrary size and orientation. In this paper, the orthotropic photoelastic model material having short fibers for the transparent type photoelastic device was developed by the embedded corrosion fiber method. It was found that the model material was satisfactory to the properties of photoelastic model material, and also that the embedded corrosion fiber method can be employed for developing a model material with arbitrary size and direction to analyze the stress distribution and crack problems of composite materials.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2003년도 추계 학술논문발표회 논문집
• /
• pp.113-117
• /
• 2003

The reliability of machined fiber reinforced composites (FRC) in high strength applications and the safety in using these components are often critically dependent upon the quality of surface produced by machining since the surface layer may drastically affect the strength and chemical resistance of the material [1,2,3,4]. Current study will discuss the characterization of fiber pull-out in orthogonal cutting of a fiber-matrix composite materials. A sparsely distributed idealized model composite material, namely a glass reinforced polyester (GFRP) was used as workpiece. Analysis method employs a force sensor and the signals from the sensor are processed using AR time series model. The experimental correlation between the fiber pull-out and the AR coefficients is examined first and effects of fiber orientation, cutting parameters and tool geometry on the fiber pull-out are also discussed.

• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.377-384
• /
• 2007

'Green' composites were fabricated from poly lactic acid (PLA) and bamboo fibers by using a conventional hot pressing method. The insulating properties of the PLA-bamboo fiber 'green' composites were evaluated by determination of the thermal conductivity, which was measured using a hot-wire method. The thermal conductivity values were compared with theoretical estimations. It was demonstrated that thermal conductivity of PLA-bamboo fiber 'green' composites is smaller than that of conventional composites, such as glass fiber reinforced plastics (GFRPs) and carbon fiber reinforced plastics (CFRPs). The thermal conductivity of PLA-bamboo fiber 'green' composites was significantly influenced by their density, and was in fair agreement with theoretical predictions based on Russell's model. The PLA-bamboo fiber composites have low thermal conductivity comparable with that of woods.

• Asian-Australasian Journal of Animal Sciences
• /
• 제33권4호
• /
• pp.615-622
• /
• 2020

Objective: The objectives were to investigate correlations between energy digestibility (digestible energy [DE]:gross energy [GE]) and various fiber types including crude fiber (CF), total dietary fiber (TDF), soluble dietary fiber (SDF), insoluble dietary fiber (IDF), neutral detergent fiber (NDF), and acid detergent fiber (ADF), and to develop prediction equations for estimating DE in feed ingredients and diets for growing pigs. Methods: A total of 289 data with DE values and chemical composition of feeds from 39 studies were used to develop prediction equations for DE. The equations were validated using values provided by the National Research Council. Results: The DE values in feed ingredients ranged from 2,011 to 4,590 kcal/kg dry matter (DM) and those in diets ranged from 2,801 to 4,203 kcal/kg DM. In feed ingredients, DE:GE was negatively correlated (p<0.001) with NDF (r = -0.84), IDF (r = -0.83), TDF (r = -0.82), ADF (r = -0.78), and CF (r = -0.72). A best-fitting model for DE (kcal/kg) in feed ingredients was: 1,356 + (0.704 × GE, kcal/kg) - (60.3 × ash, %) - (27.7 × NDF, %) with R² = 0.80 and p<0.001. In diets, DE:GE was negatively correlated (p<0.01) with NDF (r = -0.72), IDF (r = -0.61), TDF (r = -0.52), CF (r = -0.45), and ADF (r = -0.34). A best-fitting model for DE (kcal/kg) in diets was: 1,551 + (0.606 × GE, kcal/kg) - (22.1 × ash, %) - (25.6 × NDF, %) with R² = 0.62 and p<0.001. All variables are expressed as DM basis. The equation developed for DE in feed ingredients had greater accuracy than a published equation for DE. Conclusion: All fiber types are reasonably good independent variables for predicting DE of swine feeds. The best-fitting model for predicting DE of feeds employed neutral detergent fiber as an independent variable.

• Computers and Concrete
• /
• 제22권2호
• /
• pp.209-220
• /
• 2018

In order to evaluate the effect of hybrid fibers on the flexural performance of tunnel segment at room temperature, twelve reinforced self-consolidating concrete (SCC) symmetric inclination beams containing steel fiber, macro polypropylene fiber, micro polypropylene fiber, and their hybridizations were studied under combined loading of flexure and axial compression. The results indicate that the addition of mono steel fiber and hybrid fibers can enhance the ultimate bearing capacity and cracking behavior of tested beams. These improvements can be further enhanced along with increasing the content of steel fiber and macro PP fiber, but reduced with the increase of the reinforcement ratio of beams. The hybrid effect of steel fiber and macro PP fiber was the most obvious. However, the addition of micro PP fibers led to a degradation to the flexural performance of reinforced beams at room temperature. Meanwhile, the hybrid use of steel fiber and micro polypropylene fiber didn't present an obvious improvement to SCC beams. Compared to micro polypropylene fiber, the macro polypropylene fiber plays a more prominent role on affecting the structural behavior of SCC beams. A calculation method for ultimate bearing capacity of flexural SCC symmetric inclination beams at room temperature by taking appropriate effect of hybrid fibers into consideration was proposed. The prediction results using the proposed model are compared with the experimental data in this study and other literature. The results indicate that the proposed model can estimate the ultimate bearing capacity of SCC symmetric inclination beams containing hybrid fibers subjected to combined action of flexure and axial compression at room temperature.

• Composites Research
• /
• 제31권5호
• /
• pp.251-259
• /
• 2018

본 논문에서는 섬유강화복합재의 멀티스케일 해석을 위해 필요한 대규모/소규모 통계적 체적요소 모델을 개발하였다. 미시영역모델의 크기효과를 최소화하기 위해서 섬유를 최대한 포함한 거대모델을 구성하였다. 이를 위해 국부 영역의 요소 절단법을 이용하여 전체 유한요소 크기에 상관없이 신속한 격자 섬유/기지의 모델링이 가능한 요소생성기를 구성하였다. 이를 통해 대규모 통계 체적 모델을 도출하여 체적모델의 크기에 따른 국부하중 공유의 차이를 고찰하고, 섬유방향의 연속체손상역학모델을 BSVEs 모델 해석으로부터 도출 하였다. BSVEs 모델을 보편적인 RVE모델과 비교 검증하였다.

• 한국축산식품학회지
• /
• 제32권5호
• /
• pp.618-626
• /
• 2012

Citrus (Citrus unshiu S. Marcoy) industry by-products were used as a source of dietary fiber, and the effects of dietary fiber extracted from citrus peel on the proximate composition, pH, color, protein solubility, cooking loss, emulsion stability, and apparent viscosity of a chicken emulsion in model systems were examined. Chicken emulsions were prepared by adding citrus peel fiber at four different concentrations (1, 2, 3, and 4%). The apparent viscosity, redness, and yellowness of the chicken emulsion with citrus peel fiber were higher than those of the control (p<0.05). The lightness values of the chicken emulsions were lower in treatments containing citrus peel fiber (p<0.05). Furthermore, moisture content, cooking loss, and emulsion stability of the chicken emulsion with 1-2% citrus peel fiber were higher than those of other treatments (p<0.05). Fat content was lower in the treatments with added citrus peel fiber than that in the control (p<0.05). Chicken emulsions with added citrus peel fiber had improved quality characteristics, and the best results were obtained for the chicken emulsion with 2% added citrus peel fiber.

• 한국전산구조공학회논문집
• /
• 제22권6호
• /
• pp.587-596
• /
• 2009

섬유 가교 곡선은 섬유보강 시멘트 복합체의 인장 거동을 예측하고 분석하는데 중요한 요인이다. 이 연구의 목적은 ECC에서 섬유 배향각의 분포와 섬유 개수를 정량적으로 고려할 수 있는 섬유 가교 모델을 제시하는 것이다. 이를 위하여 먼저 섬유 배향각과 섬유 개수를 정량적으로 고려할 수 있는 섬유 가교 모델을 유도하였다. 섬유 배향각과 섬유 개수는 이미지 프로세싱 기법을 사용하여 계측하였다. 이미지 분석을 통하여 계측한 섬유 배향각에 대한 확률밀도함수와 섬유 개수는 섬유 배향각을 2차원이나 3차원에 무작위로 분포된 것으로 가정하는 것과 큰 차이를 보였다. 이는 타설방법이나 유동흐름에 따라 섬유 분포 특성이 영향을 받기 때문으로, 모델의 검증을 위해 정확한 섬유분포 특성을 파악할 필요가 있다. 따라서 이미지 프로세싱 방법으로 계측한 섬유 분포 특성을 근간으로 보강섬유의 배향각과 단면 내 섬유 개수를 고려하여 얻은 섬유 가교 곡선으로 1축 인장 거동을 모사하였다. 모사한 1축 인장 거동은 실험 결과와 유사하게 다중 균열과 변형률 경화 거동을 보이는 등 1축 인장 거동을 정확히 나타낼 수 있는 것으로 검증되었다.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 The Korea-Japan Joint Symposium
• /
• pp.114-114
• /
• 2003

Fiber bundles output from a draft operation have linear density irregularity. This study is dealing with modeling the dynamics of fiber bundle during roll drafting based on continuity, momentum balance, and a constitutive assumption. The simulation results from this model are compared with experimental results and analyzed by applying the concept of the Describing Function(DF). It can be confirmed that the simulation results agree well with experiments in a steady state, if the model parameters are good adjusted.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.295-300
• /
• 2003

In discontinuous composite mechanics, shear lag theory is one of the most popular model because of its simplicity and accuracy. However, it does not provide sufficiently accurate strengthening predictions in elastic regime when the fiber aspect ratio is small. This is due to its neglect of stress transfer across the fiber ends and the stress concentrations that exist in the matrix regions near the fiber ends. To overcome this shortcoming, a more simplified shear lag model introducing the stress concentration factor which is a major function of modulus ratio is proposed. It is found that the proposed model gives a good agreement with finite element results and has the capability to correctly predict the values of intefacial shear stresses and local stress variations in the small fiber aspect ratio regime.