• Computers and Concrete
• /
• v.34 no.4
• /
• pp.409-425
• /
• 2024

This paper utilizes LS-DYNA software to numerically investigate impact response and damage evaluation of fiber-reinforced polymer (FRP) bars-reinforced ultra-high-performance concrete (UHPC) composite beams (FRP-UHPC beams). Three-dimensional finite element (FE) models are established and calibrated by using literature-based static and impact tests, demonstrating high accuracy in simulating FRP-UHPC beams under impact loading. Parametric analyses explore the effects of impact mass, impactor height, FRP bar type and diameter, and clear span length on dynamic response and damage modes. Two failure modes emerge: tensile failure with bottom longitudinal reinforcement fracture and compression failure with local concrete compression near the impact region. Impact mass or height variation under the same impact energy significantly affects the first peak impact force, but minimally influences peak midspan displacement with a difference of no more than 5% and damage patterns. Increasing static flexural load-carrying capacity enhances FRP-UHPC beam impact resistance, reducing displacement deformation by up to 30%. Despite similar static load-carrying capacities, different FRP bars result in varied impact resistance. The paper proposes a damage assessment index based on impact energy, static load-carrying capacity, and clear span length, correlating well with beam end rotation. Their linearly-fitting coefficient was 1.285, 1.512, and 1.709 for the cases with CFRP, GFRP, and BFRP bars, respectively. This index establishes a foundation for an impact-resistant design method, including a simplified formula for peak midspan displacement assessment.

• Journal of Aerospace System Engineering
• /
• v.18 no.5
• /
• pp.73-80
• /
• 2024

A deep neural network (DNN) was employed to predict the spring-back of a CFRP composite spar induced by the curing process. A total of 816 spring-back data points, derived from varying stacking angles, layer counts, and flange radii, were generated through finite element method (FEM)-based curing analysis to train the DNN model. The trained model demonstrated an R-squared value of 0.99 and a mean squared error of 0.00093, indicating excellent performance. For untrained flange radii, the spring-back predicted by the DNN exhibited a mean relative error of 2.18% when compared to FEM results. Additionally, while FEM analysis required approximately 20 minutes, the DNN-based prediction required only about 14 milliseconds. These results highlight the potential of using DNNs for the rapid prediction of process-induced deformation in CFRP composites.

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.177-182
• /
• 2006

In this work, we have prepared organophilic MMT having thermal stability by ion exchange reaction of various aromatic ammonium salts with MMT containing sodium ion. The organic modifiers having alkyl side chains and amine functional group were successfully synthesized by effectively introducing the surfaces of MMT via ion exchange reaction to form organophilic MMTs with a view to improve the reactivity and thermal stability. The WAXD patterns of organophilic MMT showed the more increased gallery spacing by $3.3{\AA}$ than that of the pristine MMT and also the onset of initial decomposition of organophilic MMT was $275^{\circ}C$ as determined by a thermogravimetric analysis. The polyimide (PI) nanocomposite films based on poly(amic acid) and organophilic MMT were prepared by a solution blending followed by cyclodehydration reaction. We have investigated the dispersity of organophilic MMTs in PI matrix by using WAXD and the effect of the organophilic MMT content on the mechanical properties of PI nanocomposite films was studied.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.5
• /
• pp.666-673
• /
• 2016

Two experiments were conducted to evaluate the effects of the level of corn dry distillers grains with solubles (CDDGS) supplementation on growing performance, blood metabolites, digestion characteristics and ruminal fermentation patterns in steers grazing dormant forage. In Exp. 1, of growth performance, 120 steers ($204{\pm}5kg$ initial body weight [BW]) were distributed randomly into 3 groups (each of 40 steers), which were provided with the following levels of CDDGS supplement: 0%, 0.25%, or 0.50% BW. All groups of steers were grazed for 30 days in each of 3 grazing periods (March, April, and May). Approximately 1,000 ha of the land was divided with electric fencing into 3 equally sized pastures (333 ha in size). Blood samples were collected monthly from 20 steers in each grazing group for analysis of glucose (G), urea-nitrogen (UN) and non-esterified fatty acids. Final BW, average daily gain (ADG) and supplement conversion (CDDGS-C) increased with increasing levels of CDDGS supplementation (p<0.05).The CDDGS supplementation also increased the plasma G and UN concentrations (p<0.05). In Exp. 2, of digestive metabolism, 9 ruminally cannulated steers ($BW=350{\pm}3kg$) were distributed, following a completely randomized design, into groups of three in each pasture. The ruminally cannulated steers were provided the same levels of CDDGS supplementation as in the growing performance study (0%, 0.25%, and 0.50% BW), and they grazed along with the other 40 steers throughout the grazing periods. The dry matter intake, crude protein intake, neutral detergent fiber intake (NDFI), apparent digestibility of dry matter (ADDM), crude protein (ADCP) and neutral detergent fiber (ADNDF) increased with increasing levels of CDDGS supplementation (p<0.05). The ruminal degradation rates of CP (kdCP), NDF (kdNDF) and passage rate (kp) also increased with increasing levels of CDDGS supplementation (p<0.05). Ruminal ammonia nitrogen ($NH_3$-N) and propionate concentrations also increased with increasing levels of CDDGS supplementation (p<0.05). However, acetate concentrations decreased with increasing levels of CDDGS supplementation (p<0.05). Liquid dilution rate increased with increasing levels of CDDGS supplementation but ruminal liquid volume decreased (p<0.05). On the basis of these findings, we can conclude that CDDGS supplementation enhanced the productive performance of cattle grazing native rangeland without negatively affecting forage intake, glucose and urea-nitrogen blood concentrations, ruminal degradation and ruminal fermentation patterns.

• Composites Research
• /
• v.26 no.4
• /
• pp.207-212
• /
• 2013

In this study, the thickness optimization for uni-directional (UD) glass fiber reinforced polymer (GFRP) laminates of the spar cap of composite tidal blades was performed under the tip deflection constrains. The spar cap was composed of GFRP composites and carbon fiber reinforced polymer (CFRP) composites. The stress distributions in the blade as well as its material costs for the optimized results were additionally investigated. The optimized thickness was obtained by interacting a sequential quadratic programming (SQP) algorithm and an ABAQUS software to calculate an objective function. It was confirmed that the thickness of UD GFRP increased with a decrease of the restrained tip deflection when a thickness of UD CFRP laminates was constrained to 9 mm. The weight of the optimized spar-cap increased up to 96.2% while the maximum longitudinal tensile stress decreased up to 24.6%. The thickness of UD GFRP laminates increased with a decrease of the thickness of UD CFRP laminates when the tip deflection was constrained to 126.83 mm. The weight increased up to 40.1%, but the material cost decreased up to 16.97%. Finally, the relationships among the weight, internal tensile stress, and material costs were presented based on the optimized thicknesses of the spar cap.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.6
• /
• pp.949-956
• /
• 2020

Objective: This study was conducted to confirm the effects of new inoculants producing-antifungal or esterase substances on rye silage and its rumen fermentation indices by comparing wild with mutated types. Methods: Rye harvested at dough stage was ensiled into 3 L mini bucket silo (1 kg) for 90 d in triplicate following: distilled water at 20 μL/g (CON); Lactobacillus brevis 100D8 (AT) and its inactivation of antifungal genes (AT-m) at 1.2×10⁵ cfu/g, respectively; and Leuconostoc holzapfelii 5H4 (FD) and its inactivation of esterase genes (FD-est) at 1.0×10⁵ cfu/g, respectively. After silo opened, silage was sub-sampled for the analysis of ensiling quality and its rumen fermentation indices. Results: Among the wild type inoculants (CON vs AT vs FD), FD inoculant had higher (p<0.05) in vitro digestibilities of dry matter and neutral detergent fiber, the total degradable fraction, and total volatile fatty acid in rumen, while AT inoculant had higher (p<0.05) lactate, acetate, and lactic acid bacteria in silage. Silage pH and the potentially degradable fraction in rumen increased (p<0.05) by inactivation of antifungal activity (AT vs AT-m), but lactate, acetate, and lactic acid bacteria of silage decreased (p<0.05). In silage, acetate increased (p<0.05) by inactivation of esterase activity (FD vs FD-est) with decreases (p<0.05) of pH, ammonia-N, lactate, and yeast. Moreover, inactivation of esterase activity clearly decreased (p<0.05) in vitro digestibilities of dry matter and neutral detergent fiber, the total degradable fraction, and total volatile fatty acid in the rumen. Conclusion: This study concluded that FD inoculant confirmed esterase activity on rye silage harvested at dough stage, while AT inoculant could not be confirmed with antifungal activity due to the absence of mold in all silages.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.10
• /
• pp.979-988
• /
• 2012

The 3D structure of GDL for fuel cells was measured using high-resolution X-ray tomography in order to study material transport in the GDL. A computational algorithm has been developed to remove noise in the 3D image and construct 3D elements representing carbon fibers of GDL, which were used for both structural and fluid analyses. Changes in the pore structure of GDL under various compression levels were calculated, and the corresponding volume meshes were generated to evaluate the anisotropic permeability of gas within GDL as a function of compression. Furthermore, the transfer of liquid water and reactant gases was simulated by using the volume of fluid (VOF) and pore-network model (PNM) techniques. In addition, the simulation results of liquid water transport in GDL were validated by analogous experiments to visualize the diffusion of fluid in porous media. Through this research, a procedure for simulating the material transport in deformed GDL has been developed; this will help in optimizing the clamping force of fuel cell stacks as well as in determining the design parameters of GDL, such as thickness and porosity.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.34 no.4
• /
• pp.234-239
• /
• 2014

This experiment was conducted to evaluate the effect of seeding rates on the forage quality and productivity of direct-seeded whole crop rice at the experimental field of the Grassland and Forages Division, National Institute of Animal Science, RDA from 2007 to 2008. Whole crop rice variety, "Nokyang", developed by the National Institute of Crop Science, was directly seeded with four different seeding rates (30, 60, 90 and 120 kg/ha). There were no significant differences (p<0.05) found in emergence date, heading date, greenish and disease resistance based on the seeding rates. Plant height increased at higher seeding rates but the tiller number per plant decreased (p<0.05). The dry matter (DM) content showed no significant difference based on seeding rates (p<0.05) while the yield of fresh and dry matter increased with incremented seeding rates (p<0.05). Acid detergent fiber (ADF) content increased with higher seeding rates, but the neutral detergent fiber (NDF) content did not show a similar tendency. The total digestible nutrient (TDN) content was lowest with 120 kg/ha seeding rate. The grain ratio decreased at higher seeding rates. In economic analysis, the plot seeded at a rate of 60 kg/ha showed the highest income increment. Although high seeding rates increased the DM yield, a seeding rate of 60 kg/ha is recommended as the proper seeding rate for direct-seeded whole crop rice.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.5
• /
• pp.436-441
• /
• 2009

A fiber optic sensor is prospective to be applied to structural health monitoring. Especially, a fiber Bragg grating(FBG) sensor is one of the most popular sensors for the structural health monitoring. The FBG sensor has several demodulation systems for tracking the shift of the Bragg wavelength. The dynamic bandwidth is dependent on the demodulation system. In this paper, the sensing mechanism is that the slope of the optical spectrum of FBG could be used as its sensitivity when the tunable laser shot the monochromatic laser wavelength at the highest slope point. In this technique, the high sensitivity is guaranteed even though the sensing range is limited. In an example of the application, the composite plate embedding a FBG sensor was manufactured by using an autoclave method and the above sensing mechanism was applied to the composite plate. Firstly, the natural frequencies of the plate were successfully measured by the FBG sensor during the impact hammer test. Secondly, a high-power speaker was used to force the plate to be vibrated at the specific frequency that was one of the natural frequencies. During the shaking, the FBG sensor measures the dynamic characteristics and ESPI was also used to measure the mode shape. From the two dynamic tests, the availability of the FBG sensor system and the ESPI was proven as a technique for measuring the dynamic characteristics of composite structure.

• Journal of Chest Surgery
• /
• v.38 no.8 s.253
• /
• pp.570-575
• /
• 2005

Background: Video-assisted thoracic sympathicotomy plays an important role as an effective method for the treatment of axillary hyperhidrosis. People with axillary hyperhidrosis were not satisfied by the occurrence of the high rate of disabling compensatory hyperhidrosis and axillary resweating. Therefore, by comparing and assessing the clincal results according to the level and extent of sympathicotomy in axillary hyperhidrosis, we aim to determine which method will result in maximal benefits. Material and Method: Among 70 patients suffering from axillary hyperhidrosis having undergone thoracoscopic sympathicotomy from January 2001 through December 2003, 57 patients who responded to either telephone interview or questionnaire were included in the current study. The patients were divided into two groups, Group 1 (n=25): patients having undergone R3, 4, 5 sympathicotomy which consist of blocking the interganglionic neural fiber on the third, fourth, and fifth rib, Group 11 (n=32): patients having undergone R3,4 sympathicotomy which consist of blocking the interganglionic neural fiber on the third and fourth rib. The study parameters were satisfaction rate and degree of compensatory sweating. Result: There was no difference on age and sex, family history, combined hyperhidrosis, and mean follow up month between the two groups. Patients expressing satisfaction were $88.0\%$ in group and $56.3\%$ in groups 11 with statistically significant difference (p=0.02). Moderate to severe compensatory sweating were $52.0\%$ (embrassing 6 patients, disabling 7 patients) in group 1 and $62.5\%$ (embrassing 5 patients, disabling 15 patients) in groups 11 with no significance in the statistical analysis. Conclusion: R3, 4, 5 sympathicotomy was an effective means of treating axillary hyperhidrosis because of higher long term satisfaction rate.