• Tunnel and Underground Space
• /
• v.14 no.2
• /
• pp.154-166
• /
• 2004

A numerical stability analysis was conducted on the large oil storage caverns excavated in a rock mass under high initial horizonal stress. The behaviors of the surrounding rock mass, rockbolts, and shotcrete were analyzedr and stability of the support members were assessed. For a proper support system design, the effect of the modelling technique, cavern shape and rockbolt length on the stability of the cavern was investigated. Results show that installation timing of supports and the change in cavern shape due to stepwise excavation affect the stress induced in support members. Also found was desperate need for a numerical technique which can properly reflect the behavior of the steel fiber reinforced shotcrete.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1332-1336
• /
• 2005

It could make the LIghtweight Piezoelectric Composite Actuator (LIPCA) damageable by the cyclic large deformation. If the progressive microvoid coalescence of LIPCA interlaminar took place, the decrease of the stiffness and the weakness of stress transmission and fiber bridging effect would make the fatigue characteristics worse suddenly. Therefore, it is required to study the variation of fatigue behavior and interlaminar condition in LIPCA under resonant frequencies. These studies such as the changeable fatigue phase and interlaminar behavior of LIPCA affected by the resonant frequencies should be carried out due to the strong anisotropy of CFRP layer. Hence, these studies are as follows. 1) The residual stresses distribution of interlaminar in LIPCA using the Classical Lamination Theory (CLT). 2) Comparative analysis of interlaminar behavior for the intact LIPCA versus LIPCA containing an artificial delamination during resonant frequency.

• Transactions of Materials Processing
• /
• v.20 no.2
• /
• pp.118-123
• /
• 2011

Manufacturing of the bipolar plate of a direct methanol fuel cell (DMFC) by direct laser melting technology (DLM) was attempted. The DLM technology is highly influenced by process parameters such as laser power, scan rate and layering height. Therefore, an analysis of the DLM technology was performed under various conditions. The bipolar plates were fabricated using the DLM process with 316L stainless steel (STS 316L) plates and powder. Powder melting trials at various energy density were performed in order to select a feasible melting range for a given laser power. The melting line height increases and eventually saturates when the energy density increases, but decreases when the laser power increases at a given energy density. For the estimation of the potential performance of the bipolar plate, the surface roughness and contact resistance of the DLM layer were also analyzed. The changes of line height and thickness are useful information to report when manufacturing bipolar plate of fuel cell through the DLM process.

• Journal of Chest Surgery
• /
• v.15 no.2
• /
• pp.259-265
• /
• 1982

We have designed a new type of bubble oxygenator (KOREA-KIM VENOTHERM OXYGENATOR) made of PVC sheet and deforming mesh incorporated in the heat exchanger, and evaluated in experimental animal for the analysis of it`s efficiency. The Oxygenator has low priming volume with high flow rate up to 6 L/rain, and efficiency of heat exchanger was excellent as 1-$1.5^{\circ}C.$ using total cardiopulmonary bypass method under moderate to deep hypothermia. Average priming volume of 1317 ml with 30% hemodilution method was perfused with an average of 1.1-3.0 L/min.$M^2$of arterial blood and pure oxygen at a rate of 2-3.4 L/min for 49.6 minutes continuously in average. During total cardiopulmonary bypass, average $PaO_2$ was $159.8{\pm}60$mmHg, $PaCO_2$ $41.0{\pm}3$mmHg respectively under $SaO_2$ over 96% with systolic arterial pressure of 70 mmHg and CVP of 5-10 cm$H_2O$. Plasma free Hemoglobin was $7.0{\pm}4$ mg/dl with 25% drop of hemoglobin and hematocrit at the end of cardiopulmonary bypass. This KKV Oxygenator was observed to have excellent capabillty of oxygen and carbon dioxide gas transfer with small amount of blood trauma, and the efficiency of heat exchanger was satisfactory during cooling and rewarming of the bubbled blood. Disadvantages have included the somewhat poor deforming effect due to loose PVC fiber mesh, the extracompact character of Teflon filters, and the rough inner surface of the heat exchanger copper pipes.

• Composites Research
• /
• v.15 no.3
• /
• pp.18-29
• /
• 2002

The bending vibration and thermal flutter instability of spacecraft booms modeled as circular thin-walled beams of closed cross-section and subjected to thermal radiation loading is investigated in this paper. The thin-walled beam model incorporates a number of nonclassical effects of transverse shear, primary and secondary warping, rotary inertia and anisotropy of constituent materials. Thermally induced vibration response characteristics of a composite thin walled beam exhibiting the circumferantially uniform system(CUS) configuration are exploited in connection with the structural flapwise bending-lagwise bending coupling resulting from directional properties of fiber reinforced composite materials and from ply stacking sequence. The numerical simulations display deflection time-history as a function of the ply-angle of fibers of the composite materials, damping factor, incident angle of solar heat flux, as well as the boundary of the thermal flutter instability domain. The adaptive control are provided by a system of piezoelectric devices whose sensing and actuating functions are combined and that are bonded or embedded into the host structure.

• Textile Coloration and Finishing
• /
• v.9 no.3
• /
• pp.1-9
• /
• 1997

Plasma techniques permit modification of the surface layers of the substrate while maintaining its bulk properties. The use of plasma treatment on textile fibers and fabrics is very limited, however, the limitations, plasma treatments have been used to modify surface properties of textiles. In this study, multifunctional finish was performed by corona discharge technique for surface functionalization. Electron spectroscopy for chemical analysis(ESCA) was used to determine the ratios of carbon, oxygen, nitrogen, and phosphor at a 20$\AA$ sampling depth. K/S value and limiting oxygen index(LOI) value were used to obtain information on the effect of the finished fabrics. The mechanism of the flame retardancy was analyzed by the thermogravimetry-and the residue number. In ESCA, relative N1s intensity increased in case of mixtrure. The flame retardancy of the polyester and polyester/cotton fabrics treated with JA-6034 and JA-6050 was found to be operative mainly in the condensed phase mechanism. The multifunctional finish was better effect for the post treated finish agent.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1611-1611
• /
• 2001

The main selection parameters used by forage grass (rye and Italian rye grass) breeders are dry-matter yield, seasonal growth, persistency, disease resistance, heading date, and heading. These characteristics can all be identified usually in the segregating F2 population, however characteristics such as soluble carbohydrate level, protein, lipid and digestibility cannot be identified. The emphasis of this work is to introduce a quantitative selection process for characterization of herbage quality e.g. protein, water-soluble carbohydrates, fiber fractions, dry matter digestibility. NIRS calibrations are currently being developed for identifying grass genotypes to assist the selection process, thereby allowing the opportunity to actively breed improved herbage quality. The changes in fibre fractions, associated components and digestibility of a number of grass clones at different growth stages are being assessed changes taking place during a growing season. This will provide a database of the major changes taking place during a growing season. Attempts to classify quality differences between genotypes will be carried out using multivariate analysis of the spectral data. I addition changes associated with maturity of grass will be considered in order to develop robust calibrations.

• Carbon letters
• /
• v.7 no.2
• /
• pp.105-113
• /
• 2006

The electro-chemical removal (ECR) of water pollutants by metal-ACF electrodes from wastewater was investigated over wide range of ECR time. The ECR capacities of metallic ACF electrodes were related to physical properties such as adsorption isotherm, surface area and pore size and to reaction time. Surface morphologies and elemental analysis for the metal supported ACFs after electro-catalytic reaction were investigated by scanning electron microscopy (SEM) and energy disperse X-ray (EDX) to explain the changes in adsorption properties. The IR spectra of metallic ACFs for the investigation of functional groups show that the electro-catalytic treatment is consequently associated with the removal of pollutants with the increasing surface reactivity of the activated carbon fibers. The metal-ACFs were electro-catalytically reacted to waste water to investigate the removal efficiency for the COD, T-N, $NH_4$-N, $NO_3$-N and $NO_2$-N. From these removal results of the piggery waste using metallic ACFs substrate, satisfactory removal performance was achieved. The removal efficiency of the metallic ACFs substrate was mainly determined by the properties of the material for adsorption and trapping of organics, and catalytic effects.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.577-584
• /
• 2007

The effect of steel microfibers (SMF) on alkali-silica reaction (ASR) was investigated using two types of reactive aggregates, crushed opal and a pyrex rod of constant diameter. Cracks are less visible in the SMF mortars compared with the unreinforced mortars. Due to crack growth resistance behavior in SMF mortar specimens, the strength loss is eliminated and the ASR products remained well confined within the ASR site. The expansion and the ASR products were characterized by microprobe analysis and inductively coupled plasma (ICP) spectroscopy. The confinement due to SMF resulted in a higher Na and Si ion concentration of the ASR liquid extracted from the reaction site. The higher concentration reduced the ASR rate and resulted in a lower reactivity of the reactive pyrex rods in SMF mortars.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.4
• /
• pp.37-42
• /
• 2003

The mechanical components with high-pressure hoses are generally produced by the swaging process. The hoses are composed of the rubber materials and the reinforced braids to support tensile forces. In case they are subjected to high mechanical and thermal loads under severe operating conditions, the oil in hoses can leak at the parts of small clamping forces. In this paper, the deformation characteristics of a fiber-reinforced hose are analyzed with respect to the jaw strokes using the finite element method. The manufacturing process is modeled with a contact problem in consideration of a real situation, and the material properties based on the experimental results are used in the analysis. Examinations of the relationship between the swaging strokes and the deformation behaviors of the hose were made on the basis of the stress and strain values of the hose components. The relations between clamping forces and separating forces are also proposed, in order to estimate clamping forces corresponding to separating forces for the given model.