• Proceedings of the Korean Magnestics Society Conference
• /
• 2011.06a
• /
• pp.7-8
• /
• 2011

Basically, the lattice mismatch between film and substrate can make those BiFeO3(BFO) films distorted with strain structure. BFO phase can be stabilized on LaAlO3(LAO) represents the example of a multiferroic with giant axial ratio. Its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion and related to the rotation of the oxygen octahedra. In this study, we show that phases with a tetragonal-like epitaxial BFO films can indeed be ferroelectric and also can be stabilized via epitaxial growth onto LAO. Recent reports on epitaxial BFO films show that the crystal structure changes from nearly rhombohedral ("R-like") to nearly tetragonal("T-like") at strains exceeding approximately -4.5%, with the "T-like" structure being characterized by a highly enhanced c/a ratio. While both the "R-like" and the "T-like" phases are monoclinic, our detailed x-ray diffraction results reveal asymmetry change from MA and MC type, respectively. By applying additional strain or by modifying the unit cell volume of the film by substituting Ba for Bi, the monoclinic distortion in the "T-like" MC phase is reduced, i.e. the system approaches a true tetragonal symmetry. There are two different M-H loops for $Bi_{1-x}Ba_xFeO_{3-{\delta}}$(BBFO) and BFO films on SrTiO3(STO) & LAO substrates. Along with the ferroelectric characterization, these magnetic data indicate that the BFO phase stabilized on LAO represents the first example of a multiferroic with giant axial ratio. However, there is a significant difference between this phase and other predicted ferroelectrics with a giant axial ratio: its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion. Therefore, in going from bulk to highly-strained films, a phase sequence of rhombohedral(R)-to-monoclinic ["R-like" MA-to-monoclinic, "T-like" MC-to-tetragonal (T)] is observed. This sequence is otherwise seen only near morphotropic phase boundaries in lead-based solid-solution perovskites (i.e. near a compositionally induced phase instability), where it can be controlled by electric field, temperature, or composition. Our results show that this evolution can occur in a lead-free, stoichiometric material and can be induced by stress alone. Those major results are summarized as follows ; 1) Ba-doping increases the unit cell volume, 2) BBFO on LAO can be fully strained up to x=0.08 as a strain limit (Fig. 1), 3) P(E) & M(H) properties can be tuned by the variation of composition, strain, and film thickness.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.15-22
• /
• 2023

BNKT Ceramics, one of the representative Pb free based piezoelectric ceramics, constitutes a perovskite(ABO3) structure. At this time, the perovskite structure (ABO3) is in the form where the corners of the octahedrons are connected, and in the unit cell, two ions, A and B, are cations, A ion is located at the body center, B ion is located at each corner, and an anion O is located at the center of each side. Since Bi, Na, and K sources constituting the A site are highly volatile at a sintering temperature of 1100℃ or higher, it is difficult to maintain uniformity of the composition. In order to solve this problem, there should be suppression of volatilization of the A site material or additional compensation of the volatilized. In this study, the basic composition of BNKT Ceramics was set to Bi_0.5(Na_0.78K_0.22)_0.5TiO₃ (= BNKT), and volatile site (Bi, Na, and K sources) were coated in the form of a shell to compensate additionally for the A site ions. In addition, the physical and electrical properties of BNKT and its coated with shell additives(= @BNK) were compared and analyzed, respectively. As a result of analyzing the crystal structure through XRD, both BNKT(Core) and @BNK(Shell) had perovskite phases, and the crystallinity was almost similar. Although the Curie temperature of the two sintered bodies was almost the same (TC = 290 ~ 300 ℃), it was confirmed that the d33 (piezoelectric coefficient) and Pr (residual polarization) values were different. The experimental results indicated that the additional compensation for a shell additive causes the coarsening, resulting in a decrease in sintering density and Pr(remanent polarization). However, coating shell additives to compensate for A site ion is an effective way to suppress volatilization. Based on these experimental results, it would be the biggest advantage to develop an eco-friendly material (Lead-free) that replaced lead (Pb), which is harmful to the human body. This lead-free piezoelectric material can be applied to a biomedical device or products(ex. earphones (hearing aids), heart rate monitors, ultrasonic vibrators, etc.) and skin beauty improvement products (mask packs for whitening and wrinkle improvement).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.384-392
• /
• 1997

Potassium lithium niobate(KLN) single crystal for a nonlinear-optic material, which changes the wavelength of lasers, has a ferroelectric tetragonal tungsten bronze structure at room temperature. It has been very hard to get single crystals of good quality due to the cracks during cooling process. In order to investigate the composition change due to the evaporation of solution during the growth, the thermogravimetric analysis was carried out. In atmospheric condition at $1000^{\circ}C$ which is about $10^{\circ}C$ higher than the crystal growing temperature, the weight change was negligible amount of $1.46{\times}10^{-5}$g/($\textrm{cm}^2$hr). By using both the Pt plate as the nucleation site and the slow cooling method with temperature fluctuation, KLN single crystal of good quality of size 1 cm could be obtained. The phase transition temperature was $490^{\circ}C$, which was higher than that reported by other researchers of the other composition. The optical anisotropy due to the absorption of OH-band exists in the range of IR.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.158-165
• /
• 2010

This study reviewed terahertz technologies of time domain spectroscopy, T-ray imaging, and high rate wireless data transfer. The main topics of the terahertz research area were investigation of materials and package modules for terahertz wave generation and detection, and setup of the terahertz system for time domain spectroscopy(TDS), T-ray imaging and sub-THz wireless communication. In addition to Poly-GaAs film as a photoconductive switching antenna material, a table-top scale for the THz-TDS/imaging system and terahertz continuous wave(CW) generation systems for sub-THz data transfer and narrow band T-ray imaging were designed. Dielectric properties of ferroelectric BSTO($Ba_xSr_{1-x}TiO_3$) films and chalcogenide glass systems were characterized with the THz-TDS system at the THz frequency range. Package modules for terahertz wave transmitter/receiver(Tx/Rx) photoconductive antenna were developed.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.795-797
• /
• 1998

A $BaTiO_3$, ferroelectric material, was mixed $SrTiO_3$, $(x)BaTiO_3-(1-x)SrTiO_3$($0.7{\leq}x{\leq}1$) ceramic capacitor with stable electrical properties in high voltage was fabricated. And microstructure, electrical property were investigated with $SrTiO_3$ mol ratio. The shrinkage, open porosity, sintering density were predominated at $9BaTiO_3-0.1SrTiO_3$. Increasing $SrTiO_3$ mol ratio, curie temperature was shifted at low temperature and maximum permittivity was increased. Also, $0.9BaTiO_3-0.1SrTiO_3$ was showed stable dielectric properties at $25{\sim}80[^{\circ}C]$. V-I properties of specimen were observed in the temperature range of $21{\sim}143[^{\circ}C]$, were divided into three regions. The region I below 10[kV/cm] was shown Ohmic conduction, the region II from 10 to 30[kV/cm] was explained by the Poole-Frenkel emission theory and the region III above 30[kV/cm] was analysed by the tunneling effect.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.2
• /
• pp.29-34
• /
• 2003

Ferroelectric YMnO$_3$ thin films were etched with Ar/C1$_2$ and CF$_4$/C1$_2$ Plasma. The maximum etch rate of YMnO$_3$ thin film was 300 $\AA$/min at a Cl$_2$/Ar gas mixing ratio of 8/2, an RF power of 800 W, a do bias of-200 V, a chamber pressure of 15 mTorr, and a substrate temperature of 3$0^{\circ}C$. From the X-ray photoelectron spectroscopy (XPS) analysis, yttrium was not only etched by chemical reactions with Cl atoms, but also assisted by Ar ion bombardments in Ar/C1$_2$ plasma. In CF$_4$/C1$_2$ plasma, yttrium formed nonvolatile YF$_{x}$ compounds and remained on and the etched surface of YMnO$_3$. Manganese etched effectively by forming volatile MnCl$_{x}$ and MnF$_{y}$. From the X-ray diffraction (XRD) analysis, the (0004) diffraction peak intensity of the YMnO$_3$ thin film etched in Ar/Cl$_2$ plasma shows lower than that in CF$_4$/Cl$_2$ plasma. It indicates that the crystallinty of the YMnO$_3$ thin film is more easily damaged by the Af ion bombardment than the changes of stoichiometry due to nonvolatile etch by-products.cts.s.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.94-98
• /
• 2005

$RuO_2$ is widely studied as a lower electrode material for high dielectric capacitors in DRAM (Dynamic Random Access Memories) and FRAM (Ferroelectric Random Access Memories). In this study, the effects of hydrogen, oxygen, and argon Electron Cyclotron Resonance (ECR) plasma pretreatments on deposited by Metal Organic Chemical Vapor Deposition (MOCVD) $RuO_2$ nucleation was investigated using X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Atomic Force Microscopy (AFM) analyses. Argon ECR plasma pretreatment was found to offer the highest $RuO_2$ nucleation density among these three pretreatments. The mechanism through which $RuO_2$ nucleation is enhanced by ECR plasma pretreatment may be that the argon or the hydrogen ECR plasma removes nitrogen and oxygen atoms at the TiN film surface so that the underlying TiN film surface is changed to Ti-rich TiN.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.1
• /
• pp.14-17
• /
• 2002

The effects of substrate temperatures and annealing temperatures on the microstructures and ferroelectric properties of PbZ $r_{0.52}$ $Ti_{0.48}$ $O_3$(PZT) thin fims prepared by pulsed laser deposition (PLD) were investigated. For this purpose, the PZT films were deposited at various substrate temperatures (400~$600^{\circ}C$) with post annealing process in oxygen atmosphere. The single perovskite phase was formed at the deposition temperature of 500 to 55$0^{\circ}C$ without post annealing and the PZT films deposited below 50$0^{\circ}C$ formed the single phase with post annealing at $650^{\circ}C$. The grain size of the films increased and the grain boundary of the films was clearly defined as the substrate temperature increased from 400 to 55$0^{\circ}C$. The remnant polarization (Pr) and the coercive field (Ec) of the films deposited at 55$0^{\circ}C$ and annealed at $650^{\circ}C$ were 34.3 $\mu$C/c $m^2$and 60.2 kV/cm, respectively.y.y.

• Electrical & Electronic Materials
• /
• v.10 no.2
• /
• pp.134-140
• /
• 1997

PbTiO$_{3}$-PbZrO$_{3}$-Pb(Ni$_{1}$3/Nb $_{2}$3/O$_{3}$)(PZT-PNN) thin films were prepared from corresponding metal organics partially stabilized with diethanolamine by the sol-gel spin coating method. Each mol rates of PT:PZ:PNN solutions were #1(50:40:10), #2(50:30:20), #3(45:35:20) and #4(40:40:20), respectively. The spin-coated PZT-PNN films were sintered at the temperature from 500.deg. C to 600.deg. C for crystallization. The P-E hysteresis curve was drawn by Sawyer-Tower circuit with PZT-PNN film. The coercive field and the remanent polarization of #4(40:40:20 mol%) PZT-PNN film were 28.8 kV/cm and 18.3 .mu.C/cm$^{2}$, respectively. Their dielectric constants were shown between 128 and 1120, and became maximum value in MPB(40:40:20 mol%). The leakage currents of PZT-PNN films were about 9.4x 10$^{-8}$ A/cm$^{2}$, and the breakdown voltages were about 0.14 and 1.1 MV/cm. The Curie point of #3(45:35:20 mol%, sintered at 600.deg. C) film was 330.deg. C.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.4
• /
• pp.369-374
• /
• 2015

In this paper, an EM sensing based prestressing force estimation method is proposed, in which it can estimate tensile force of PS tendon for PSC girder. The PSC girder has more improved performance than the general concrete girder by introducing the prestressing to the concrete. Thus the PSC girder bridge is widely constructed due to its high performance and low cost. However, the prestressing force has not been managed nevertheless it is major factor for the maintenance of the PSC girder bridge. The prestressing force was just measured during construction using jacking device and after that, it can not be managed. For this reason, this paper proposes a tensile force estimation method of PS tendon based on EM sensor. The permeability of ferroelectric material is changed according to the induced stress to the material, in which it can be measured using EM sensor. To measure the permeability of PS tendon, the EM sensor was fabricated and verified by performing the MTS test. The test was performed using 7-wire steel tendon under the 0, 40, 80, 120, 160, 200 KN of tensile force. The permeability of PS tendon was gradually decreased according to the increasement of tensile force. The regression method was used to find the relation between permeability and stress. As a result, the permeability has linear relation with the tensile force of PS tendon and the pre-stressing force can be estimated by the derived estimation equation.