• 암석학회지
• /
• 제27권3호
• /
• pp.109-120
• /
• 2018

경상분지 남동부 일대의 백악기 및 제3기 암류에서 발달하는 단층분절에 대한 분포특성을 도출하였다. 선형을 보이는 267조의 단층분절은 광역 지질도 상에서 표시된 곡선의 단층선에서 추출하였다. 첫째, 단층분절에 대한 방향각(${\theta}$)-길이(L)의 도면을 작성하였다. 관계도에서 단층분절의 전반적인 분포형태를 도출하였다. 도면의 분포곡선은 전체 형태에 따라서 4개의 구간으로 구분하였다. 상기 구간의 정점에 해당하는 북북동, 북북서 및 서북서의 방향은 양산, 울산 및 가음 단층계의 방향을 시사한다. 단층분절의 집단은 최대 정점에 해당하는 $N19^{\circ}E$의 방향에 대하여 거의 대칭 분포를 보여 준다. 둘째, 방향각-빈도수(N), 평균 길이(Lm), 총 길이(Lt) 및 밀도(${\rho}$)의 도면을 작성하였다. 관계도에서 상기한 도면의 전 영역을 분포곡선의 분포상에 의하여 19개의 영역으로 구분하였다. 상기한 영역의 정점에 해당하는 방향은 암체에 가해진 대표적인 응력의 방향을 시사한다. 셋째, 18개의 부집단에 대한 길이-누적 빈도수 그래프를 작성하였다. 관계도에서 지수(${\lambda}$)는 시계방향($N10{\sim}20^{\circ}E{\rightarrow}N50{\sim}60^{\circ}E$)과 반시계방향($N10{\sim}20^{\circ}W{\rightarrow}N50{\sim}60^{\circ}W$)으로 갈수록 증가한다. 반면 길이의 분포 폭 및 평균 길이는 감소한다. 서로 다른 진화 특성을 갖는 상기한 부집단에 대한 도면은 진화과정의 한 단면을 나타내고 있다. 넷째, 18개의 그래프에 대한 종합 분포도를 작성하였다. 관계도에서 상기한 그래프를 분포 구역에 따라 5개의 그룹(A~E)으로 분류하였다. 단층분절의 길이는 그룹 E ($N80{\sim}90^{\circ}E{\cdot}N70{\sim}80^{\circ}E{\cdot}N80{\sim}90^{\circ}W{\cdot}N50{\sim}60^{\circ}W{\cdot}N30{\sim}40^{\circ}W{\cdot}N40{\sim}50^{\circ}W$) < D ($N70{\sim}80^{\circ}W{\cdot}N60{\sim}70^{\circ}W{\cdot}N60{\sim}70^{\circ}E{\cdot}N50{\sim}60^{\circ}E{\cdot}N40{\sim}50^{\circ}E{\cdot}N0{\sim}10^{\circ}W$) < C ($N20{\sim}30^{\circ}W{\cdot}N10{\sim}20^{\circ}W$) < B ($N0{\sim}10^{\circ}E{\cdot}N30{\sim}40^{\circ}E$) < A ($N20{\sim}30^{\circ}E{\cdot}N10{\sim}20^{\circ}E$)의 순으로 증가한다. 특히 그래프의 형태는 균등 분포에서 지수 분포로 점차 변화한다. 마지막으로, 단층분절의 길이에 대한 여섯 개 변수의 값을 5개 그룹으로 구분하였다. 여섯 개 변수 중, 평균 길이 및 가장 긴 단층분절의 길이는 그룹 III ($N10^{\circ}W{\sim}N20^{\circ}E$) > IV ($N20{\sim}60^{\circ}E$) > II ($N10{\sim}60^{\circ}W$) > I ($N60{\sim}90^{\circ}W$) > V ($N60{\sim}90^{\circ}E$)의 순으로 감소한다. 그룹 V에 속하는 단층분절의 빈도수, 최장 길이, 총 길이, 평균 길이 및 밀도가 가장 낮은 값을 보여 준다. 5개 그룹 사이의 상기 배열순은 단층분절의 상대적인 생성시기와의 상관성을 시사한다.

• Journal of Magnetics
• /
• 제21권4호
• /
• pp.561-569
• /
• 2016

Although pretty methods have been proposed to reduce torque ripple, they generally suffer from the decreased torque density. This paper will investigate the spoke-type interior permanent magnet (IPM) machine with shaping methods, including the sinusoidal (SIN), the inverse cosine (ICS), the sinusoidal with third harmonic (SIN+3rd), and the inverse cosine with third harmonic (ICS+3rd). In order to obtain low torque ripple and high torque density, the shaping method applied in rotor and stator at the same time, termed as the dual-shaping method, is proposed. This method is analytically derived and further confirmed by finite element method (FEM). It turns out that the ICS and ICS+3rd shaping methods are more suitable for outer rotors, while the SIN and the SIN+3rd shaping method should be used in inner stators. The original machine, the singular shaped machines and the dual-shaped machines on electromagnetic performances are compared for evaluation. The results verify that the dual-shaping method can improve torque density, whilst reducing torque ripple.

• 자원환경지질
• /
• 제22권2호
• /
• pp.91-102
• /
• 1989

The gravity measurement has been conducted at 61 stations with an interval of about 500 to 1,000 m along two survey lines of about 47 Km between $Chungju-Jech{\check{o}}n$ and $Salmi-D{\check{o}}cksanmy{\check{o}}n$ in order to study on the subsurface geologic structure and structural relation between $Okch{\check{o}}n$ Group and Great Limestone Group of $Chos{\check{o}}n$ Supergroup. The Bouger gravity anomalies were obtained from the reduction of the field observations, and the distribution patterns of the basement and subsurface geologic structure were interpreted by means of the Fourier-Series and Talwani method for two-dimensional body. The depth of Conrad discontinuity varies from 12.7 Km to 15.7 Km, and vertical displacements along the Osanri and Bonghwajae faults are 1.0 Km and 1.5 Km, respectively between Chungju and $Jech{\check{o}}n$. The depth of Conrad discontinuity varies from 13.8 Km to 15.4 Km, and vertical displacement along the Bonghwajae fault is 0.5 Km between Salmi and $D{\check{o}}cksanmyon$. The basement is widely exposed at several places between Chungju and $Jech{\check{o}}n$. In the unexposed area between Osanri and $W{\check{o}}lgulri$, its depth is from 1.5 Km to 2.1 Km. It is displaced downward along the Osanri and Bonghwajae faults by 0.8 Km and 0.6 Km, respectively, and is displaced upward along the Dangdusan fault by 1.6 Km. On the other hand, the depth of the basement varies abruptly by the Sindangri, Jungwon, Kounri, and Bonghwajae faults between Salmi and $D{\check{o}}cksanmy{\check{o}}n$, and it is from 2.8 Km to 3.2 Km around $Salmimy{\check{o}}n$, from 1.6 Km to 2.5 Km between the Sindangri and Bonghwajae faults, 3.0 Km near Koburangjae, and 2.5 Km at $Doj{\check{o}}nri$. The high Bouguer gravity anomalies are due to the accumulation of $Okch{\check{o}}n$ Group and $Jangs{\check{o}}nri$ Metamorphic Complex whose density is higher than the basement exposed between Sondong and Osanri, and imply the existance of Bonghwajae Metabasite or hornblende gabbro of high density distributed along the Bonghwajae fault in the vicinity of Koburangjae. The low Bouguer gravity anomalies resulted form the fracture zone associated with fault or rock of low density imply the existance of the Osanri, Bonghwajae, Dangdusan faults and $Daed{\check{o}}cksan$ thrust between Chungju and $Jech{\check{o}}n$, the uplift of the basement by the Sindangri, Jungwon, Kounri, and Bonghwajae faults, and extensive distribution of Cretaceous biotite granites between Salmi and $Docksanmy{\check{o}}n$. The thickness of $Okch{\check{o}}n$ metasediments varies from 1.5 Km to 3.2 Km, and that of Great Limestone Group of $Chos{\check{o}}n$ Supergroup from 200 m to 700 m. It is interpreted that $Okch{\check{o}}n$ Group is in contact with Great Limestone Group of $Chos{\check{o}}n$ Supergroup by the fault zones of the Bonghwajae and $Daed{\check{o}}cksan$ faults, and the Bongwhajae fault is a thrust of high angle, by which the east of the basement is displaced downward 0.5 Km between Chungju and lechon, and 1.0 Km between Salmi and $D{\check{o}}cksanmy{\check{o}}n$.

• 전기학회논문지
• /
• 제57권3호
• /
• pp.398-402
• /
• 2008

Recently, the development of superconducting fault current limiters (SFCLs) has been required as power demands increase in the power system. A distribution-level prototype resistive SFCL using coated conductor (CC) has been developed by Hyundai Heavy Industries Co., Ltd. and Yonsei University for the first time in the world. The ratings of the SFCL are 13.2kV/630A at normal operating condition. A novel non-inductive winding method is used in fabricating coils so there is almost zero impedance during normal operation. The distribution SFCL is cooled by sub-cooled liquid nitrogen $(LN_2)$ of 65K and 3 bar to enhance cryo-dielectric performance, critical current density, and thermal conductivity. In order to make reliable operation of an SFCL in real power systems, we monitored and controled its operation conditions by using supervisory control and data acquisition (SCADA) method. Thus, a monitoring system for the SFCL employing information technology (IT) is proposed and developed to be on the lookout for the operation conditions such as inside temperature, inside pressure, $LN_2$ level, voltage and current. Since operation temperature should be kept constant, bang-bang control for temperature feedback with a heater attached to the cold head of cryo-cooler is applied to the system. Short-circuit tests with prospective fault current of 10kA and AC dielectric withstand voltage tests up to 143kV for 1 minute were successfully performed at Korea Electrotechnology Research Institute. This paper deals with the development of a distribution level SFCL and its monitoring system for reliable operation.

• 한국산학기술학회논문지
• /
• 제22권3호
• /
• pp.13-19
• /
• 2021

n형 SiC 반도체에서 적층 결함이 열전 물성에 미치는 영향에 대해 연구하였다. ��-SiC 분말 성형체를 질소 분위기에서 1600~2100 ℃, 20~120분간 열처리해서 30~42 %의 기공률을 갖는 다공질 SiC 반도체를 제작하였다. X선 회절 분석으로 적층 결함량, 격자 스트레인 및 격자 상수를 산출하였고, 미세 구조 분석을 위해서 기공률 및 비표면적 측정과 함께, 주사 전자현미경 (SEM), 투과 전자현미경 (TEM) 및 고분해능 전자현미경 (HREM) 등을 관찰하였다. Ar 분위기 550~900 ℃에서 도전율과 Seebeck 계수를 측정 및 산출하였다. 열처리 온도가 높을수록, 처리 시간이 길어질수록 캐리어 농도 증가 및 입자와 입자간의 연결성 향상에 의해 도전율이 향상되었다. 도너로 작용하는 질소의 고용으로 Seebeck 계수는 음(-)의 값을 나타내었고, 도전율과 마찬가지로 열처리 온도 및 시간이 상승함에 따라 Seebeck 계수의 절대 값이 증가하였다. 이는 적층 결함의 감소, 즉 입자 및 결정 성장과 함께 적층 결함 밀도의 감소에 의해 포논의 평균 자유 행정이 증가해서 결과적으로 포논-드랙 효과에 의한 Seebeck 계수의 향상으로 나타난 것으로 판단된다.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2007년도 High Temperature Superconductivity Vol.XVII
• /
• pp.68-68
• /
• 2007

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.353-360
• /
• 2016

Series hybrid electric vehicles (SHEVs) having multiple power sources such as an engine- generator (EnGen), a battery, and an ultra-capacitor require a power control unit with high power density and reliable control operation. However, manufacturing using separate individual power converters has the disadvantage of low power density and requires a large number of power and signal cable wires. It is also difficult to implement the optimal power distribution and fault management algorithm because of the communication delay between the units. In order to address these concerns, this approach presents a design methodology and a power control algorithm of an integrated power converter for the SHEVs powered by multiple power sources. In this work, the design methodology of the integrated power control unit (IPCU) is firstly elaborately described, and then efficient and reliable power distribution algorithms are proposed. The design works are verified with product-level and vehicle-level performance experiments on a 10-ton SHEV.

• 전자공학회논문지C
• /
• 제35C권8호
• /
• pp.10-22
• /
• 1998

To handle the density increase of SRAMs, a new parallel testing methodology based on built-in self test (BIST) is developed, which allows to access multiple cells simultaneously. The main idea is that a march algorithm is dperformed concurently in each baisc marching block hwich makes up whole memory cell array. The new parallel access method is very efficient in speed and reuqires a very thny hardware overhead for BIST circuitry. Results show that the fault coverage of the applied march algorithm can be achieved with a lower complexity order. This new paralle testing algorithm tests an .root.n *.root.n SRAM which consists of .root.k * .root.k basic marching blocks in O(5*.root.k*(.root.k+.root.k)) test sequence.

• Progress in Superconductivity
• /
• 제3권2호
• /
• pp.183-187
• /
• 2002

In this paper we analyzed the electromagnetic behavior of high $-T_{c}$ superconductor under the quench state using finite element method. Poisson equation was used in finite element analysis as a governing equation and was solved using algebra equation using Gallerkin method. We first investigate d the electromagnetic behavior of U-type superconductor. Finally we applied our analysis techniques to 5.5 kVA meander-line superconducting fault current limiters (SFCL) which are currently developed by many power-system researcher in the world. Meshes of 14,600 elements were used in analysis of this SFCL. Analysis results show that the distribution of current density was concentrated to inner curvature in meander-line type-superconductors and maximum current density 14.61 $A/\m^2$ and also maximum Joule heat was 6,420 W/㎥. We concluded that this meander line-type SFCL was not pertinet fur uniform electromagnetic field distribution.n.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.88-95
• /
• 2002

Recent development in the field of RE-Ba-Cu-O (REBCO, RE: Y or rare earth elements) bulk high-Tc superconductors (HTS) is reviewed in the present paper. After the fatal weak link problem of sintered REBCO superconductors has been overcome by melt processing, this field has been greatly advanced during last ten years. The critical current density $J_c$ at 77 K has been enhanced by introducing effective flux pinning sites into the $REBa_2Cu_3O_y$ (RE123) superconducting matrix. Large melt-textured REBCO bulk crystals have been fabricated with the TSMG(top-seeded melt growth) technique. Mechanical properties of REBCO bulks have been improved by using the Ag additive or epoxy resin. Real bulk applications such as current lead, fault current limiter, flywheel energy storage system, magnetic field source, magnetic separation system, and etc., surely come true near future.