• Journal of Korea Foundry Society
• /
• v.17 no.5
• /
• pp.472-479
• /
• 1997

The effect of size and mass fraction of SiC particulate on the fatigue and wear have been investigated for semi-liquid formed SiCp/AZ91HP Mg composites. In the study, different particulate sizes of 7, 20, $50 {\mu}m$ were prepared with various mass fraction for sample preparation. By tension-tension fatigue tests, whose procedures are standardized in ASTM standard 647E-93, the da/dN vs. ${\Delta}K$ curves were obtained. Also, the crack propagation paths were observed by optical microscope. As a result of wear test, specific wear loss is decreased with increasing mass fraction and particulate size. Specific wear loss of 30 mass% $50 {\mu}m$ SiC reinforced Mg composite is compared to SKD11.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.6 s.261
• /
• pp.701-709
• /
• 2007

To clarify the characteristics of surface damage due to fretting in press-fitted shaft, experimental methods were applied to small scale specimen with different bending load condition. Fatigue tests and interrupted fatigue tests of press-fitted specimen were carried out by rotate bending fatigue test. Macroscopic and microscopic characteristics were examined using scanning electron microscope (SEM), optical microscope or profilometer. It is found that small fatigue cracks are nucleated early in life regardless of bending stress, and thus the most portion of fatigue life on press fits can be considered to be crack propagation process. Most of surface cracks are initiated near the contact edge, and multiple cracks are nucleated and interconnected. Furthermore, the fretting wear rates at the contact edge are increased rapidly at the initial stage of total fatigue life. It is thus suggested that the fatigue crack nucleation and propagation process is strongly related to the evolution of surface profile by fretting wear in press fits.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.478-483
• /
• 2011

Cast mold has low wear-resistance comparing with other alloyed molds which result in lower production rate and high cost of products. Recently, various weld methods are being applied to increase the wear-resistance of molds and to extend mold life. Among them, nickel alloy weld process increases the hardness irrelevant to its machinability and creates very uniform structures. In addition, it causes better wear-resistance and reduces shrinkage defects. In this paper, we analyze the mold surface cracks welded by nickel alloy and propose the methods to improve the mold surface and its wear-resistance. It has been found that nickel alloy weld does not affect the inside crack of mold but has an influence on the surface crack seriously. Results show that the start and growth of fatigue cracks have been delayed about 3 times and reduced approximately 75%, respectively, and the mold surface cracks are decreased about 5.7 times.

• Transactions of Materials Processing
• /
• v.6 no.5
• /
• pp.435-445
• /
• 1997

In order to study the manufacturing possibility of connecting rod by direct quenching method, the difference between connecting rod by direct quenching and that by general heat treatment were investigated by observing microstructure, by measuring mechanical properties, by conducting fatigue testing, and by measuring the amount of tool wear in actual cutting. Connecting rod manufactured by direct quenching had better fatigue life than that by general heat treatment, which was due to homogeneous microstructure, and higher strength. The amount of cutting tool wear of connecting rod by direct quenching was higher than that by general heat treatment, which was due to low machinability and high toughness of tempered martensite microstructure. Therefore it will be added the study of heat treatment and cutting condition for manufacturing by direct quenching.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.40-46
• /
• 2001

An integrated analysis for the thermo-elastic deformation, fatigue, wear and brittle damage evolution of the shrink-fitted die with multi stress-ring of dissimilar materials is presented. A simple numerical algorithm for the moving elastic boundaries characterizing the contacts of the insert and multi stress-rings is presented. The initial stress distribution in the die due to shrink-fit is considered and the traction at the die surface contacting with the work piece is obtained by analyzing the elasto-plastic deformation of work piece. Elastic analysis of the separate-type die is performed and then the evolution of brittle damage, wear and fatigue life are predicted. This integrated analysis is applied to the extrusion die with two layers of stress-rings and the results are discussed in detail.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1587-1590
• /
• 2005

A rigid-plastic finite element analysis for the die forging process of a socket ball joint, which is used in the transportation system, was carried out. And also with the results, the elastic stress analysis for the forging die was performed in order to get basic data for the die life prediction. The die fatigue life prediction was simulated using Goodman's and Gerber's equation. The prediction technique for the fatigue life of a forged product, the socket ball joint, using DEFORM-3D is presented and the results are commented upon. Archard's wear model was used for the wear simulation and then the wear simulation and then the wear quantity was quantity was evaluated using volume. In order to prove the wear simulation results to be reliable, wear quantity of the real forging die set in used a forging factory was measured using a 3-dimensional measurement apparatus. The simulation results were relatively in good agreement with the experimental measurements.

• Tribology and Lubricants
• /
• v.29 no.6
• /
• pp.366-371
• /
• 2013

Various heat treatment and surface coating methods have been applied to machine parts. Nowadays, diamond-like carbon (DLC) coatings are widely used because of their excellent tribological characteristics. Despite the numerous studies on DLC-coated engineering surfaces, the exact wear mechanisms related to the coating thickness and elastic modulus have not been fully examined. In this study, a sliding contact problem between a small spherical hard particle and a DLC-coated steel surface is analyzed using a nonlinear finite element code, MARC. The maximum principal stress distributions and deformed surfaces are compared for different coating thicknesses and Young's modulus values. Plastically deformed surface shapes such as a groove and torus indicate that the most dominant wear mechanism for a DLC-coated surface is abrasive wear. Fatigue wear can also play a role in a case where the coating thickness is relatively large and the elastic modulus is high.

• Structural Engineering and Mechanics
• /
• v.64 no.6
• /
• pp.819-826
• /
• 2017

The effects of thermocycling procedure and material shade on the mechanical properties and wear resistance of resin-based dental restorative materials are investigated. The modulus of elasticity, hardness, plasticity index and wear resistance are determined for the conventional composite, the nanohybrid composite and the nanofilled dental composites. Disc-shape samples are prepared from each material to investigate the effects of thermocycling procedure on the mechanical properties and wear resistance of different types of dental restorative materials. In this respect, a group of samples is thermocycled and the other group is stored in ambient conditions. Then nano-indentation and nano-scratch tests are performed on the samples to measure their mechanical properties and wear resistance. Results show that the A1E shade of the dental nanocomposite possesses higher modulus of elasticity and hardness values compared to the two other shades. According to the experimental results, the mean values for the modulus of elasticity and hardness of the A1E shade of the nanocomposite are 13.71 GPa and 1.08 GPa, respectively. The modulus of elasticity and hardness of the conventional dental composite increase around 30 percent in the oral environment due to the moisture and temperature changes. The wear resistance of the dental composites is also significantly affected by moisture and temperature changes in the oral conditions. It is observed that thermocycling has no significant effect on the hardness, plasticity index and wear resistance of the nanohybrid composite and the nanocomposite dental materials.

• Journal of the Korean Society for Railway
• /
• v.20 no.4
• /
• pp.512-520
• /
• 2017

On a typical railway, trains travel using the friction between the wheel and the rail. Contact pressure is generated between the wheel and the rail, and the magnitude of the contact pressure changes depending on the weight, speed, wheel-set hunting, and contact point of the vehicle. In this study, the contact characteristics were analyzed through the finite element analysis for the wheel/rail system on curved track, and fatigue damage and wear rate of wheel/rail according to contact pressure were analyzed through rolling contact fatigue test. Results indicate that, general and heat treated rails showed higher wear rate than wheels, and general and heat treated rail wear rate increased rapidly over a certain number of repetitions. In addition, the general rail wear rate was about 7 ~ 15% higher than that of the heat treated rail, and a regression equation for the rail wear rate with the contact pressure in the contact pressure range of 900 ~ 1,500 MPa was presented.

• Tribology and Lubricants
• /
• v.28 no.1
• /
• pp.1-6
• /
• 2012

In this paper, a three elastic body sliding contact problem is modeled to investigate more precise wear mechanisms related with the sealing surface. A 3-D finite element contact model, a small spherical elastic particle, PTFE seal and steel surface, is solved using a nonlinear finite element code MARC. The deformed seal and steel surface shapes, von-Mises and principal stress distributions are obtained for different seal sliding distances. The entrapped small particle within PTFE seal results in very high stresses on the steel surface which exceeded its yield strength and produce plastic deformation such as groove and torus. The sealing surface could also be worn down by sub-surface fatigue due to intervening small particles together with the well-known abrasive wear. Therefore the proposed contact model adopted in this paper can be applied in design of various sealing systems, and further studies are required.