• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.725-728
• /
• 2004

In this study, the effect of mode II by variation of multilevel loading direction was experimentally investigated in the fatigue crack propagation behavior. To generate mixed-mode I+II loading state, the compact tension shear(CTS) specimen and loading device were used in this tests. The experimental method divided into three steps and three cases that were step I(0$^{\circ}$), step II(30$^{\circ}$, 60$^{\circ}$, 90$^{\circ}$),step III(0$^{\circ}$) and case I(0$^{\circ}$ ⇒ 30$^{\circ}$ ⇒ 0$^{\circ}$), case II(0$^{\circ}$ ⇒ 60$^{\circ}$ ⇒ 0$^{\circ}$), case III(0$^{\circ}$ ⇒ 90$^{\circ}$ ⇒ 0$^{\circ}$). The result of test, the step II affected to the step III in the all case. Specially, The fatigue crack propagation rate was faster and the fatigue life was smaller than of mixed mode I+II(30$^{\circ}$,60$^{\circ}$) due to the effect of mode II in the step III of the case III

• Structural Engineering and Mechanics
• /
• 제23권4호
• /
• pp.353-367
• /
• 2006

Two full-scale, precast, pretensioned box girders were subjected to shear-dominated loading, one under monotonic loads to failure and the other subjected to one-half million cycles of fatigue loads followed by monotonic ultimate loads. The number of cycles was selected to allow for comparison with previous research. The fatigue loads were applied in combination with occasional overloads. In the present study, fatigue loading reduced the shear capacity by only six percent compared to the capacity under monotonic loading. However, previous research on flexure-dominated girders subjected to the same number of repeated loads showed that fatigue loading changed the mode of failure from flexure to shear/flexure and the girder capacity dropped by 14 percent. The comparison of the measured data with calculated shear capacity from five different theoretical methods showed that the ACI code method, the compression field theory, and the modified compression field theory led to reasonable estimates of the shear strength. The truss model led to an overly conservative estimate of the capacity.

• Journal of Welding and Joining
• /
• 제20권2호
• /
• pp.59-64
• /
• 2002

When the vehicle travels in an actual road, resistance spot weldments of the vehicle structure are exposed to complex loading state. Since the fatigue strength in resistance spot weldment of vehicle body can be determined by effect of residual stresses and loading state of driving, estimating actual loading state and considering residual stress effect are needed. In this study, Fatigue stress-fatigue life relation concerned residual stress effect was obtained by thermo elastic plastic finite element analysis. And applied loading in resistance spot weldments of vehicle body was calculated by dynamic analysis. Presumption of fatigue life was performed using proposed method

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.79-84
• /
• 2000

Crack closure and growth behavior of physically short fatigue cracks under random loading are Investigated by performing narrow- and wide-band random loading tests for various stress ratios. Artificially prepared two-dimensional, short through-thickness cracks are used. The closure behavior of short cracks under random loading is discussed, comparing with that of short cracks under constant-amplitude loading and also that of long cracks under random loading. Irrespective of random loading spectrum or block length, the crack opening load of short cracks is much lower under random loading than under constant-amplitude loading corresponding to the largest load cycle in a random load history, contrary to the behavior of long cracks that the crack opening load under random loading is nearly the same as or slightly higher than constant-amplitude results. This result indicates that the largest load cycle in a random load history has an effect to enhance crack opening of short cracks.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.274-278
• /
• 2007

The purpose of this study is to analyze the important loads related with crack-growth in aircraft. Al Alloys mainly used in aircraft are Al2024 and Al7075 in Duralumin. In random fatigue loading, it has been understood crack-growth characteristic using fractured surface photograph by SEM. In order to obtained CTOD, we measured a crack size in wing frame part. As a result of fatigue experiment that accumulating plenty of fatigue loadings, we find more cracks than that produces in the same fatigue loading. The important loads relating to crack-growth was found in the largest strain cycle. Applying strain block in fatigue experiment, it is actually loading in connection of aircraft. In conclusion, These results can be used for preventing an accident owing fatigue-fracture in aircraft.

• 한국안전학회지
• /
• 제9권2호
• /
• pp.18-25
• /
• 1994

In this thesis, the fatigue tests were performed on a series of reinforced concrete to Investigate the variation of strength and the safety of reinforced concrete structures under fatigue load. The specimens were of the same rectangular cross-section, of effective height 24cm and width 30cm and their span was 330cm. The three point loading system is used in the fatigue tests. In these tests, the fracture mode of reinforced concrete structures under fatigue load, relationship between the repeated loading cycles and the mid-span displacement of the specimens were observed. According to the test results, the following fatigue behavior of reinforced concrete specimens were observed. By increasing of the number of repeated loading cycles, the mid-span displacement became greater, however the Incremental amounts of the displacement were reduced. It could be also known that the inelastic strain energy of the doubly reinforced rectangular beams was larger than that of the singly reinforced rectangular beams as increasing the number of repeated loading cycles. Compliance of reinforced concrete structures tended to be reduced as increasing the repeated loading cycles, and the compliance of the doubly reinforced rectangular beams was generally smaller than that of the singly reinforced rectangular beams. Based on the above investigation, it could be concluded that the doubly reinforced rectangular beams under fatigue load were more efficient to resist the brittle fracture than the singly reinforced rectangular beams.

• 대한토목학회논문집
• /
• 제8권2호
• /
• pp.167-175
• /
• 1988

본 연구의 목적은 변동하중을 받는 구조부재의 피로거동을 해석하는 것이다. 이 연구의 해석과정은 다음과 같다. (1) 도로교의 실동응력파측정 및 통계적해석 (2) 등가의 일정진폭하중과, 통계적해석에 의해 모형화된 변동하중하(下)의 피로시험 (3) 등가응력개념의 RMC 모델에 의한 변동하중하(下)의 피로해석 등가응력개념에 의한 변동하중하(下)의 피로해석은 대부분의 구조용강재의 균열성장속도회귀지수가 $m{\fallingdotseq}3$이므로 이론적으로 RMC 모델이 합당하다. 변동하중하(下)의 피로시험해석결과 RMC 모델이 기존의 RMC 모델보다 변동하중에 의한 피로거동치(da/dN-${\Delta}K$, $N_f$)에 더 가까웠다. 또 변동하중하(下)에서 응력범위의 변화로 인한 interaction효과나 응력범위적용순서(sequence)효과 등은 피로수명에 거의 영향을 미치지 않으며, 응력범위변화속도가 클수록 피로균열성장속도가 빨라짐을 알 수 있었다.

• 대한기계학회논문집A
• /
• 제32권10호
• /
• pp.856-865
• /
• 2008

Damage mechanisms in bending piezoelectric actuators under electric fatigue loading are addressed in this work with the aid of an acoustic emission (AE) technique. Electric cyclic fatigue tests have been performed up to $10^7$ cycles on the fabricated bending piezoelectric actuators. An applied electric loading range is from -6 kV/cm to +6 kV/cm, which is below the coercive field strength of the PZT ceramic. To confirm the fatigue damage onset and its pathway, the source location and distributions of the AE behavior in terms of count rate and amplitude are analyzed over the fatigue range. It is concluded that electric cyclic loading leads to fatigue damages such as transgranular damages and intergranular cracking in the surface of the PZT ceramic layer, and intergranular cracking even develops into the PZ inner layer, thereby degrading the displacement performance. However, this fatigue damage and cracking do not cause the final failure of the bending piezoelectric actuator loaded up to $10^7$ cycles. Investigations of the AE behavior and the linear AE source location reveal that the onset time of the fatigue damage varies considerably depending on the existence of a glass-epoxy protecting layer.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권1호
• /
• pp.50-57
• /
• 2017

Purpose : This paper is a comparative analysis results of the fatigue test for dental implants and accelerated life test by using a static type loading device commonly used in Korea and a dynamic type loading device (universal-joint) recommended by FDA. Methods : Fatigue tests of dental implant is based on ISO 14801 and classified into static load test and dynamic load test. The tests were carried out on three test specimens by four load stress steps under each loading device. For analysis on failure mode such as crack, fracture and permanent deformation of test specimens, we used X-ray three-dimensional computed tomography on test specimens before and after the fatigue tests. The design of the accelerated life test was based on the analysis results of the fatigue life data obtained from the dynamic load test and the statistical analysis software (Minitab ver.15) was used to analyze the appropriate life distribution. Results : As a result of the fatigue tests and the accelerated life tests at same acceleration condition under each test method, the fatigue life under the dynamic type loading device (universal-joint) was shorter than when static type loading device was applied. Conclusion : This paper can be used as a reference when the universal-joint type loading device for implants fatigue test is applied as ISO 14801.

• 대한토목학회논문집
• /
• 제28권6D호
• /
• pp.819-829
• /
• 2008

콘크리트 포장에 반복적으로 재하되는 차량의 하중에 의하여 슬래브의 동적강도는 꾸준히 감소하며 장기적으로 피로균열이 발생한다. 온도와 수분의 분포에 의하여 슬래브 내에는 항상 응력이 도입되어 있으므로 이를 고려한 후 차량하중의 영향을 추가해야만 보다 정확하게 콘크리트 포장의 피로수명을 예측할 수 있다. 따라서, 본 연구에서는 기존에 개발된 대표적 피로모형들의 각종 인자들을 평가하고 모형으로부터 데이터를 추출하여 환경하중을 고려하는 새로운 피로모형을 개발하였다. 국내 각 지역의 기상 및 교통조건을 사용하여 국내에서 일반적으로 시공되는 콘크리트 포장에 대한 피로해석을 수행하여 개발된 피로모형의 적용성을 평가하였다. 슬래브 하부에서 발생한 상향의 균열보다는 슬래브 상부의 인장응력에 의한 하향의 균열이 피로파손의 주요한 원인으로 판단되었다. 본 연구결과를 바탕으로 한 후속 연구를 통하여 차량의 속도가 고려된 피로해석도 수행될 수 있을 것으로 기대된다.