• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.1
• /
• pp.84-92
• /
• 1989

The purpose of this paper is to demonstrate the effect of a FH spread spectrum communication interference in TV channels and frequency compatibility in 30-88 MHz frequency band. To calculate this interferece, the strength of electric field of TV signals is derived as a function of distance between TV transmitter and receiver. An interference model is established based upon thefield strength by using the relation between the transmitted power of FH spread spectrum communications and the distance between the TV image signals, which makes TV screen a cceptble, Simultaneous transmission of FH sprea spectrum signals and TV signals is shown to be feasible, as far as the interference level is lower than the TV image signal level by 23.5dBm. As a result of frequency analysis and experiment, the FH spread spectrum communication can be used together with TV channels.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.2
• /
• pp.121-136
• /
• 1989

In this paper, an attempt has been made to analyze the theoretically and verify experimentally the effect of curvature on the radiation characteristics of microstrip array antennas mounted conformally on the concave surface and the convex surface of the cylindrical body. The analysis of single element microstrip antenna is made by using the analysis method of Transmission Line Model. The theory of array antennas is established by application of the method of transformed coordinates, in which the translation and the ratation about each single element arrayed two-demensionally on the nonplanar surface are under consideration, and it is investigated by computation of the synthetic electric field strength in the far zone. In addition, various radiation characteristics, such as return loss, resonant frequency, radiation pattern, half-power, beamwidth, gain, are measrued and compared with the theroetical values according to the variation of curvature, by designing and building 4-element array microstrip antenna operating at 10 GHz, and microstrip feed lines. As predicted in theroy, it is verified that radiation pattern of antennas mounted on the concave and the convex surfaces alike broadens as the radius of curvature decreases. And for the curved surfaces, aggrement between computed values of the total synthetic radiation power pattern by the method of transformed coordinates and measured valuse is good. Besides, it is found that resonant frequency, input impedance and gain are hardly affected by the radius of curvature.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3A
• /
• pp.303-310
• /
• 2004

In this paper, L-shaped slot antenna for 5.15㎓-5.35㎓ is designed, fabricated. and measured. The prototype consist of four L-shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are four L-slot length. width, position, air-gap height. and feed Point position. From these parameters optimized, a four L-shaped slot antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the fabrication four L-shaped slot antenna is 5.25㎓, bandwidth for approximately 5％(VSWR＜1.5) and the gain is 8-9㏈i. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in H-Plane and I-Plane are 69$^{\circ}$and 62$^{\circ}$, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1269-1275
• /
• 2003

In this paper, nonradiative dielectric(NRD) rotman lens with a gap-coupled unidirectional dielectric radiator(UDR) has been designed. Gap-coupled UDR is structurally suitable for NRD rotman lens. We have optimized NRD rotman lens for minimizing side-lobe, and calculated design parameters of UDR such as length of resonator and distance of gap using an equivalent circuit model of an evanescent NRD guide. Experimental prototype of UDR is fabricated and measured at the center frequency of 38 GHz. The simulated S-parameter and far-field radiation beam pattern of UDR show good agreements with measured data. Finally, total beam pattern of NRD rotman lens of multi-beam feed has been obtained using a measured pattern of UDR and array factor of NRD rotman lens. The obtained beam pattern shows remarkably suppressed side-lobe.

• Structural Engineering and Mechanics
• /
• v.66 no.2
• /
• pp.217-227
• /
• 2018

In the last decades, valuable results have been reported regarding conventional passive, active, semi-active, and hybrid structural control systems on two-dimensional and a few three-dimensional shear buildings. In this research, using a three-dimensional finite element model of high-rise concrete structures, designed by performance based plastic design method, it was attempted to construct a relatively close to reality model of concrete structures equipped with Tuned Mass Damper (TMD) by considering the effect of soil-structure interaction (SSI), torsion effect, hysteresis behavior and cracking effect of concrete. In contrast to previous studies which have focused mainly on linearly designed structures, in this study, using performance-based plastic design (PBPD) design approach, nonlinear behavior of the structures was considered from the beginning of the design stage. Inelastic time history analysis on a detailed model of twenty-story concrete structure was performed under a far-field ground motion record set. The seismic responses of the structure by considering SSI effect are studied by eight main objective functions that are related to the performance of the structure, containing: lateral displacement, acceleration, inter-story drift, plastic energy dissipation, shear force, number of plastic hinges, local plastic energy and rotation of plastic hinges. The tuning problem of TMD based on tuned mass spectra is set by considering five of the eight previously described functions. Results reveal that the structural damage distribution range is retracted and inter-story drift distribution in height of the structure is more uniform. It is strongly suggested to consider the effect of SSI in structural design and analysis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.515-523
• /
• 2012

In this paper, the resonance characteristics and radiation characteristics of a spherical patch on a dielectric sphere are analyzed. Resonance characteristics can be obtained from the resonant frequency and the quality factor. Radiation characteristics can be also analyzed from the E-field in the far region. In order to calculate these parameters, spectral domain analysis method is applied. Algebraic equation can be obtained in spectral domain through Vector Legendre transform pair and Galerkin's method. So, efficient calculation is possible numerically. It is investigated that radius, curvature of a spherical patch, and dielectric constant of a dielectric sphere have an effect on characteristics of a spherical patch.

• Nuclear Engineering and Technology
• /
• v.42 no.5
• /
• pp.568-575
• /
• 2010

Flow Accelerated Corrosion is an active degradation mechanism of CANDU feeder. The tight bend downstream to Gray loc weld connection, close to reactor face, suffers significant wall thinning by FAC. Extensive in-service inspection of feeder wall thinning is very difficult because of the intense radiation field, complex geometry, and space restrictions. Development of a knowledge-based inspection program is important in order to guarantee that adequate wall thickness is maintained throughout the whole life of feeder. Research results and plant experiences are reviewed, and the plant inspection databases from Wolsong Units One to Four are analyzed in order to support developing such a knowledge-based inspection program. The initial thickness before wall thinning is highly non-uniform because of bending during manufacturing stage, and the thinning rate is non-uniform because of the mass transfer coefficient distributed non-uniformly depending on local hydraulics. It is obvious that the knowledge-based feeder inspection program should focus on both fastest thinning locations and thinnest locations. The feeder wall thinning rate is found to be correlated proportionately with QV of each channel. A statistical model is proposed to assess the remaining life of each feeder using the QV correlation and the measured thicknesses. W-1 feeder suffered significant thinning so that the shortest remaining life barely exceeded one year at the end of operation before replacement. W-2 feeder showed far slower thinning than W-1 feeder despite the faster coolant flow. It is believed that slower thinning in W-2 is because of higher chromium content in the carbon steel feeder material. The average Cr content of W-2 feeder is 0.051%, while that value is 0.02% for W-1 feeder. It is to be noted that FAC is reduced substantially even though the Cr content of W-2 feeder is still very low.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.73-79
• /
• 2008

We propose a novel metal-waveguide structure for sustaining long-range surface-plasmon-polaritons (LRSPP). The LRSPP waveguides are composed basically of two asymmetric metal layers: a very thin, finite-width metal strip on top of a metal slab with a dielectric gap in between them. Mode cut-off of LRSPPs excited on the double-metal waveguides is characterized by consistently investigating their dispersion relations and mode profiles. We also confirm experimentally the existence of low-loss, well-confined LRSPP modes by measuring far-field outputs emerging from an edge of the asymmetric double-metal waveguides. In the experiment, we have fabricated several types of SPP waveguide devices including straight lines, S-bend, and Y-branch consisting of gold strips (20 nm-thick, $5{\mu}m$-wide). Overall propagation loss of the proposed double-metal waveguides is quite comparable to that of single metal-strip waveguides, in addition the mode sizes can be tuned by increasing the core-insulator gap between the metal layers to get a higher coupling efficiency with a single-mode fiber in telecom wavelength. The proposed LRSPP waveguides may open up realization of SPP-waveguide sensors or nonlinear SPP-devices by replacing the core-insulator with a bio-fluid or a nonlinear medium.

• The Research Journal of the Costume Culture
• /
• v.18 no.1
• /
• pp.93-108
• /
• 2010

R$\ddot{o}$hrer index, Vervaeck index and Body Mass Index(BMI) are frequently used in order to judge obese subjects in clothing & textiles field. However, there are no certain criteria of judging the degree of obesity. Each researcher utilized these obesity indices according to their own criteria so far. Therefore, the purpose of the study is to suggest a reliable obesity index and new criteria for judging the degree of obesity. The results are as follows; Utilizing frequency analysis, main percentiles, minimums, maximums and ranges were presented by 5 age groups from twenties to sixties. Obesity rates dramatically increased, the subject got older. Especially, obesity rate of the subjects in their fifties and sixties were much higher than other age groups. 1.6 & higher can be used in the R$\ddot{o}$hrer index, 98 & higher can be used in the Vervaeck index, and 25 & higher can be used in the BMI as the Optimal criteria of the obesity. Total of 24 body measurements and 3 obesity indices were used for analyzing the correlation analysis. All heights measurements showed negative correlation with the 3 obesity indices. It is determined heights measurements have high correlation with R$\ddot{o}$hrer index compare to other indices. Crotch height, interscye back, neck shoulder point to breast point, bust circumference, waist circumference, upper arm circumference and armscye circumference have high positive correlation with all obesity indices. According to the ANOVAs by each percentile group of the R$\ddot{o}$hrer and Vervaeck indices, there are big significances in all measurements and obesity indices except arm length. In general, heights decreased significantly by getting bigger, while circumferences and lengths, widths and indices increased rapidly by getting bigger. The results of the analysis by each percentile group in the BMI, it showed the significant differences in the all measurements except cervical height and arm length. There were similar tendency of differences according to the degree of the obesity in BMI percentile groups. It was confirmed that the BMI is the most reliable index for judging the obesity owing to the high correlations and significant differences with other measurements.

• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.420-427
• /
• 1993

Dielectric thin film mirrors are embedded in multimode and single-mode fibers by a fusion splicing technique. The fibers with $45{\circ}$ angled embedded mirrors serve as ultra-compact directional couplers with low excess optical loss of 0.2 dB for multimode and 0.5 dB for single mode at 1.3 ${\mu}m$ and excellent mechanical properties. The reflectance is wavelength dependent and strongly polarization depencient. Far-field scans of the reflected output power measured with a white-light source show a pattern which is almost circularly symmetric with aspect ratio of 1.09 at 5% of the peak power. The splitting ratio in a multimode coupler measured with a diode laser source is much less dependent on input coupling conditions than in conventional fused biconical-taper couplers, indicating that these couplers are less susceptible to modal noise occuring in optical fiber communication systems. Spectral properties of multilayer internal mirrors normal to the fiber axis have been investigated experimentally, and a matrix analysis has been used to explain the results.