• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.841-848
• /
• 2006

There is a complex variation of stress in PSC anchorage zones and box girder diaphragms because of large concentrated load by prestress. According to the AASHTO LFRD design code, three-dimensional effects due to concentrated jacking loads shall be investigated using three-dimensional analysis procedures or may be approximated by considering separate submodels for two or more planes. In this case, the interaction of the submodels should be considered, and the model loads and results should be consistent. However, box girder diaphragms are 3-dimensional disturbed region which requires a fully three-dimensional model, and two-dimensional models are not satisfactory to model the flow of forces in diaphragms. In this study, the strengths of the prestressed box girder diaphragms are predicted using the 3-dimensional grid strut-tie model approach, which were tested to failure in University of Texas. According to the analysis results, the 3-dimensional strut-tie model approach can be possibly applied to the analysis and design of PSC box girder anchorage zones as a reasonable computer-aided approach with satisfied accuracy.

• Composites Research
• /
• v.36 no.6
• /
• pp.441-447
• /
• 2023

Recently, as demand for high-strength, lightweight materials has increased, there has been great interest in joining with metals. In the case of mechanical bonding, such as bolting and riveting, chemical bonding using adhesives is attracting attention as stress concentration, cracks, and peeling occur. In this paper, surface treatment was performed to improve the adhesive strength, and the change in adhesive strength was analyzed. For the adhesive strength test were conducted with Carbon Fiber Reinforced Plastic(CFRP), CR340(Steel), and Al6061(Aluminum), and laser and plasma surface treatment were used. After plasma surface treatment, the adhesive strength improved by 7.3% and 39.2% in CFRP-CR340 and CFRP-Al6061, respectively. CR340-Al6061 was improved by 56.2% in laser surface treatment. Surface free energy(SFE) was measured by contact angle after plasma treatment, and it is thought that the adhesion strength was improved by minimizing damage through a chemical reaction mechanism. For laser surface treatment, it is thought that creates a rough bonding surface and improves adhesive strength due to the mechanical interlocking effect. Therefore, surface treatment is effect to improve adhesive strength, and based on this paper, the long-term fatigue test will be conducted to prevent fatigue failure, which is a representative cause of actual structural damage.

• Journal of Venture Innovation
• /
• v.7 no.1
• /
• pp.201-223
• /
• 2024

This study undertook an empirical analysis to examine the impact of various factors on entrepreneurial intention among young people, with a particular focus on the role of startup mentoring. Employing a survey distributed nationwide, data from 250 valid respondents were subjected to structural equation modeling to investigate these dynamics. The analysis uncovered that workplace stress, subjective norms, and perceived behavioral control positively influence the entrepreneurial intentions of youth. Meanwhile, technological constraints negatively affected these intentions. The study did not explore the potential effects of future uncertainty and the burden of failure. Significantly, it was found that startup mentoring plays a crucial role in mitigating the negative impacts that may deter young individuals from pursuing entrepreneurship. Mentoring was instrumental in reducing negative influences, thereby fostering a more conducive environment for entrepreneurial ambition. By integrating the Push-Pull-Mooring (PPM) and Theory of Planned Behavior (TPB) models, this research not only validates these frameworks within the context of youth entrepreneurship but also underscores the essential function of startup mentoring in enhancing entrepreneurial intentions. The insights from this study highlight the importance of mentoring programs in nurturing the entrepreneurial spirit among the youth, suggesting that targeted mentoring support can play a pivotal role in overcoming barriers to entrepreneurship.

• Journal of the Korean Arthroscopy Society
• /
• v.9 no.2
• /
• pp.167-173
• /
• 2005

Purpose: The purpose of this study is to evaluate the clinical results of posterior cruciate ligament (PCL) and posterolateral structure (PLS) reconstruction using bilateral hamstring tendon autografts. Materials and Methods: From October 2002 to March 2004, ten patients were received PCL and PLS reconstruction simultaneously using bilateral hamstring autografts. PCL was reconstructed using ipsilateral hamstring tendon and fixed with cross pins and Intrafix (Mitek, Norwood, MA). PLS was reconstructed using contralateral hamstring tendon. The mean follow up was 17 months. Clinical assessments consisted of Lysholm knee scores, International Knee Documentation Committee (IKDC) evaluation form and posterior stress radiographs. External rotation of tibia was evaluated at $30^{\circ}\;and\;90^{\circ}$ knee flexion using Noyes and Barber-Westin's classification. Contralateral harvest site morbity was evaluated using IKDC evaluation form and flexion power of the knee. Results: Mean posterior displacement of tibia using stress radiographs was improved from 13.3 mm to 3.7 mm. In tibial external rotation evaluation, 7 patients were functional, 2 patients were partially functional and one failure. The average Lysholm knee score improved from 54 preoperatively to 86 postoperatively. At the final IKDC evaluation, 8 patients were graded as nearly normal, 2 were graded as abnormal. In contralateral harvest site morbidity evaluation, 2 patients complained of numbness around the wound but negligible. Conclusion: PCL and PLS reconstruction using bilateral hamstring autografts was considered as a good treatment method with minimal contralateral harvest site morbidity.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.1
• /
• pp.29-38
• /
• 2009

Statement of problem: A casting connection technique is widely used for repair, correction and addition to base metal framework. However, a casting connection technique may increase the risk of failure in clinical situations when high stresses exist. Purpose: The purpose of this study was to investigate the mechanical retentive groove design comparatively to increase the joint strength by using the three-dimensional finite element analysis model of a 3-unit fixed partial denture. Material and methods: Ten finite element models were constructed. (Model A: One retentive groove, Model B: Two retentive grooves, Model C: Three retentive grooves, Model D: Four retentive grooves, Model E: One horizontal groove and two vertical grooves, Model F: Two horizontal grooves and one vertical groove, Model G: One groove with the enlarged dimension, Model H: Two grooves with the enlarged dimension, Model I: One groove with the increased height, Model J: One groove with the increased width of base). The vertical force was applied to the mesial and the distal fossa to the casting connection of mandibular first molar. Results: The main factors, affecting joint strength of casting connection were both the retention between the primary cast and the secondary cast and the thickness of the primary cast remaining after preparing retentive groove. The increase of retentive force, according to the numbers and the dimension of retentive groove had an effect on distributing stress. However, in some cases, the increase of retentive force resulted in the increase of stress by reducing thickness of the primary cast in the connection area. Conclusion: The design of retentive groove that limits number of retentive groove for metal thickness and increases the depth of retentive groove for retention is highly recommended.

• Journal of Biomedical Engineering Research
• /
• v.24 no.5
• /
• pp.401-410
• /
• 2003

This study investigates the biomechanical efficacies of various cement augmentation techniques with or without pressurization for varying degrees of osteoporotic femur. For this study, a biomechanical analysis using a finite element method (FEM) was undertaken to evaluate surgical procedures, Simulated models include the non-cemented(i.e., hip screw only, Type I), the cement-augmented(Type II), and the cemented augmented with pressurization(Type III) models. To simulate the fracture plane and other interfacial regions, 3-D contact elements were used with appropriate friction coefficients. Material properties of the cancellous bone were varied to accommodate varying degrees of osteoporosis(Singh indices, II∼V). For each model. the following items were analyzed to investigate the effect surgical procedures in relation to osteoporosis of varying degrees : (a) von Mises stress distribution within the femoral head in terms of volumetric percentages. (b) Peak von Mises stress(PVMS) within the femoral head and the surgical constructs. (c) Maximum von Mises strain(MVMS) within the femoral head, (d) micromotions at the fracture plane and at the interfacial region between surgical construct and surrounding bone. Type III showed the lowest PVMS and MVMS at the cancellous bone near the bone-construct interface regardless of bone densities. an indication of its least likelihood of construct loosening due to failure of the host bone. Particularly, its efficacy was more prominent when the bone density level was low. Micromotions at the interfacial surgical construct was lowest in Type III. followed by Type I and Type II. They were about 15-20% of other types. which suggested that pressurization was most effective in limiting the interfacial motion. Our results demonstrated the cement augmentation with hip screw could be more effective when used with pressurization technique for the treatment of intertrochanteric fractures. For patients with low bone density. its effectiveness can be more pronounced in limiting construct loosening and promoting bone union.

• Journal of agricultural medicine and community health
• /
• v.39 no.3
• /
• pp.161-175
• /
• 2014

Objectives: This study investigates the prevalence of suicide ideation and its the related factors by gender among Korean adults. Methods: National cross-sectional data from the database of the first and second year of $5^{th}$ Korean National Health and Nutritional Examination Survey (KNHANES V-1, V-2) were used for this study. 13,165 adults (${\geq}20$ years) were included in this analysis. Results: The prevalence of suicide ideation was 9.8% for men, 18.9% for women. Renal failure, depression, melancholy, stress, perceived health status, and smoking were significant risk factors among both men and women for suicide ideation. Divorced, separated or widowed of marital status and severe physical activity were related factors of suicide ideation for men. Low educational attainment, and alcohol dependency were associated factors of suicide ideation for women. Conclusions: There was gender difference of prevalence and risk factors of suicide ideation. These gender differences should be considered for planning and implementing suicide prevention program.

• Korean Journal of Soil Science and Fertilizer
• /
• v.40 no.3
• /
• pp.201-207
• /
• 2007

To reduce both the floatation of the seedling of rice and the failure in standing in the paddy field when the barley straw was applied to paddy field before planting the rice, we tested the effect of rice rooting with plowing methods and irrigation rates for 2 years from 2003 to 2004. This study was carried out in paddy field with Fluvio-Marine deposit in Jeonbug series and the operating accuracy and the change of soil physico-chemical properties depending on plowing methods and irrigation rates following the barley straw applying were examined. There was a less floatation of barley straw in the dry-rotaryI+water-rotaryI(DRI+WRI) plot than in the plowing+water-rotary(PL+WRI) plot. The ratio of miss-planted and floating seedling also decreased by 1.7%, 2.6% in the DRI+WRIplot compared with PL+WRI plot. The soil physical property was improved with the decreasing soil hardness, bulk density and increasing soil porosity after the application of barley straw, especially enhanced greatly in the increase of porosity, gaseous phase and with the decrease of soil hardness, bulk density of subsurface soil in DRI+WRI plot. And the change of soil chemical property were increased the content of total carbon$^{\circ}{\S}$nitrogen$^{\circ}{\S}$organic matter and available phosphate while decreased the content of exchangeable cations and available silicate after the application of barley straw. Also the content of organic matter, available phosphate and cation exchangeable capacity were increased, whereas caron/nitrogen ratio was decreased in DRI+WRI plot compared with PL+WRI plot. The number of panicles, spikelets per square meter were increased and 1,000 grains weight of hulled rice was gained more in DRI+WRI plot at irrigation rate of $500ton\;ha^{-1}$, in DRI+WRII plot at irrigation rate of $700ton\;ha^{-1}$. So the rice yields were increased by 7%, in DRI+WRI and 5% in DRI+WRII plot, respectively compared with PL+WRI plot. The result of this study indicated that the most appropriate plowing method with barley straw application on rice cultivation at double cropping in normal paddy field plain land was DRI+WRI.

• The korean journal of orthodontics
• /
• v.25 no.1 s.48
• /
• pp.55-72
• /
• 1995

The purpose of this study is to evaluate the effects of mechanical and thermal fatigue on the shear bond strength(SBS) in orthodontic brackets bonded to human premolars with chemically cured adhesive(Mono-$Lok^2$, Rocky Mountain Orthodontics). Two types of metal brackets (Ormesh, Microloc) and three types of ceramic brackets (Fascination, Starfire, Transcend 2000) were used in this study. The $10^6$ loadcycles of $|7.4{\times}10{^2}sin2{\pi}ft|g{\cdot}cm$ and the 1,000 thermocycles of 15 second dwell time each in $5^{\circ}C\;and\;55^{\circ}C$ baths were acturated as mechanical and thermal fatigue stress, and SBS were measured after each fatigue test. The fracture sites were examined by stereoscope and scanning electron microscope. The results obtained were summarized as follows, 1. In static shear bond test, Fascination brackets showed the maximum SBS($20.78\pm3.45$ MPa) and Microloc brackets showed the minimum SBS($14.88\pm3.10$ MPa). Fascination and Starfire brackets showed significantly greater SBS than Microloc brackets(P<0.05). 2. In mechanical fatigue test, Fascination brackets showed the maximum SBS ($20.19\pm3.45$ MPa) and Starfire brackets showed the minimum SBS($9.10\pm8.33$ MPa). The SBS or Transcend 2000 brackets(P<0.01) and Starfire brackets(P<0.05) significantly decreased after $10^6$ loadcycles. 3. In thermocycling test, Ormesh brackets showed the maximum SBS ($19.36\pm2.76$ MPa) and Starfire brackets showed the minimum SBS($11.94\pm6.86$ MPa). The SBS of Transcend 2000(P<0.01), Microloc and Starfire brackets(P<0.05) significantly decreased after $10^3$ thermocycles. 4. Failure sites of thermocycling groups were similar to those of static groups but after mechanical fatigue test, Ormesh and Transcend 2000 brackets failed at the bracket/resin interface and Microloc brackets failed within adhesive. Facination brackets failed at the enamel/resin interface irrespective of experimental condition.

• Tuberculosis and Respiratory Diseases
• /
• v.57 no.5
• /
• pp.411-418
• /
• 2004

Background : Cigarette smoking is the single biggest avoidable cause of death and disability in most countries. Effective prevention of cigarette Smoking and help for those wishing to quit can therefore yield enormous health benefits for populations and individuals. Although most of smokers try to stop smoking for themselves, the success rate of quitting smoking is very low. Promoting and supporting smoking cessation should be an important health policy priority for healthcare professionals in all clinical settings. In this study, we tried to evaluate the effect of the educational program for smoking cessation of our hospital, the smoking pattern, and characteristics of adult smokers enrolled in the program. Methods : We enrolled 640 smokers, who has visited the '5 day stop smoking school' for smoking cessation from Jan 1998 to 2001. we evaluated the characteristics of the smokers based on the self report questionnaire at the beginning of the program and we also checked 100 smokers, enrolled in Inpatient Smoking Cessation Educational program, their smoking behavior and the cessation rate with postal questionnaire after finishing this program from Nov 2002 to Jan 2003. Results : The health was most common motivation for smoking cessation. The stress was the most important motivation of smoking. The overall smoking cessation rate of the smokers enrolled in inpatient smoking cessation school was 60%. The age of starting smoking and the kind of occupation have a significant difference between the success group and failure group of smoking cessation. Conclusion : The inpatient smoking cessation program was effective smoking cessation intervention in the adult smokers who enrolled in '5 day stop smoking school'.